Search:

The EP3 knuckle assembly won't fit onto your EJ8 due to it being MacPherson strut and the EJ8 is double wishbone.

I know for sure the EP3 rear calipers will fit on the DC2R trailing arms but you...

Yes, the non-folding mirrors are stock on US and Canadian 96-00 Civics.

http://farm3.static.flickr.com/2234/2352457387_f388e05c9c_o.jpg
...

Yes...

Odometer will be more difficult to change. For the brown clip, grab your cluster harness near the clip and twist and pull.

I know on newer Integra odometers, there's a plastic piece that prevents...

It will definitely accelerate quicker, but your RPMs will be higher at a certain speed.

Which 4.9FD are you interested in getting? ATS? MFactory?

The offset is too low. I believe stock offset is +50. The wheels will be sticking out too much.

15 x 6.5 +40 would be the best choice. I ran 15 x 6.5 +42 with 205/50/15 on my hatch without rubbing, no wheel gap.

It really is simple. There is only 5 screws total.

As mentioned..

1. Two top phillips screws on the dash bezel.
2. Pull the dash bezel from the bottom first, the whole piece will come out.
3....

Yes, the DIY should work.

Use a flathead screwdriver and push the clip part out a little further so it catches the dash.

The top part of the metal clip

http://www.speedcomplex.com/resize/IMG_0485.JPG

Yes, the EG and DC share the same chassis. All suspension parts are interchangeable. However, in order to use DC2R rear struts on an EG, you need the DC2R rear LCAs. JDM EG6 rear LCAs are similar to...

The stud pattern is indeed 4x100. Generally a good offset for the Del Sol, as well as EGs and non-ITR DCs is anywhere between +40 to +45.

Here's a really good writeup on how to mount an EG front...

The DC5 suspension is different, MacPherson over Double Wishbone. Knuckles are completely different shape.

Yes, our USDM EM1 did come with a 26mm front and 13mm rear. In the link I posted above, it shows installation of our EM1 26mm bar which is exactly the same as the EK9 bar/lcas.

This is the EK9...

The top diagram is from the USDM 99-00 Civic Si EM1. The lower diagram is from the USDM 96-00 Civic EX EJ8. Since the EK4 would be closely related to the EM1 as terms as engine and other...

The EK9/EM1 use a different shaped front sway compared to the lower trims.

http://www.slhondaparts.com/images/PCI/13S020/009/9.jpg



The 'normal' shaped sway for the lower trims are shaped...

I had Skunk2 sleeved coilovers and the ride is stiffer, but bearable. What is your suspension and driving plans? The S2 sleeves are good for daily driving.

Here are reviews on the S2 Pro...

This is the 26mm front sway, correct? You will also need the front strut forks from the EK9 or EM1. The EK9/EM1 front LCAs are of different design and you need the strut forks along with it.

The kit does come with a cig lighter extender piece. But that USDM console will not fit 100% in a RHD civic.

The climate control takes two #74 bulbs.

http://www.superbrightleds.com/specs/74_t15.htm

I had DC5 Recaros using DB8 Recaro rails in my EG. There was no modification except for the inner rear brackets I had to use a longer bolt.

Same concept.

Here's how to swap seat pans...

http://honda-tech.com/zerothread?id=347548

Don't know if rust is a problem down there, but check for the normal quarter panel cancer.

Function 7 makes aftermarket ITR LCAs