Search:

Red CL9: https://www.facebook.com/media/set/?set=a.128486430631645.1073741827.113851428761812&type=1


http://smg.photobucket.com/user/sousuke/library/CL7%20Euro%20R/wing?sort=3&page=1

well you can do it like how afgmoh did, but some people rather do a proper job and securely bolt/screw it down. Please don't go buying the cheap ebay shit. Spend a bit more money and get good decent...

Also, you should have a relay harness for the foglights if you're doing a HID conversion, especially if you're gonna go 55W, as the stock wiring was only designed for halogens.

To be honest with...

Take off the bumper if you haven't already, just makes it so much easier. You can mount it on the bumper supports..

Alternatively, if you don't want to take the bumper off, I suppose you can...

Did some research and found this:

http://www.tsxclub.com/forums/655319-post5.html

Can someone clarify that this is the same with our Euro's

Kinda didn't quite know what you meant when I first read it, but kinda just figured out there was something keeping the boot lever held down. So I just pried that piece out. I'll upload a picture for...

They should, but even if they don't it's very unlikely water's going to get in there. Even if you drive through a puddle, just the way the car's designed, it's hard for water to get into the fender...

55W should be fine, if you're scared about it getting cracked, do a foglight HID projector retrofit (think there's a thread where some guy's chucked in lexus ones). But if you're really anal, you can...

It's H11, but you can use H9's with minor modifications with almost 2x the light output.

You should be fine. I've read about people's lenses cracking and whatnot, but I've never had a problem.
Running 55W HID's on my foggies, been through heavy rain, thick fog, even washed it with the...

Thanks Aaron!!

@Aaron, thanks for the info, just seems like a bitch to take off. I just shoved the speaker cables from underneath since I couldn't take it out when I wired the front driver's. If you can just pull...

Isn't the kick panel the bit underneath the steering wheel.... it's where the coin box and VSA switches are...

I'm referring to the door panel (the plastic bit where the boot/petrol cap lever is. not the door trim. I've removed the door trim countless times, so have no problems with that.) As I've said, the...

No, no signs of corrosion. Though I wish it were that simple. I've taken it rubber cover off and it's perfectly fine, no current/voltage reading though..

Would you happen to know how to take the...

@ Moderators, would you be able to move this to a general discussion forum rather than model specific?

narh, it's probably 2 things:
1) the connection to the BCM or
2) the wiring is disconnected somewhere (i.e. in the driver door panel)


If someone can link me to how I can remove the driver...

The black rubber housing you're referring to is the door ajar.

I've tested it, no reading. Bolt's really firmly secured too.

Need help here. My driver's side door ajar sensor isn't working.

I've tried troubleshooting the problem, all the power windows, central locking and speakers are all working, I get a power reading...

I can second what afgmoh said, I'm running pretty much the same setup, with alpine 15" type S sub. You can get the 6.5" splits as well rather than the 6" if you want a bit more mid bass, not sure if...

Would a 18x9.5 with a +20 offset fit??

If not, the would 18x8.5 +35??

23303

found a pic of what it'd look like...

what you guys reckon?

get it or a no go?

d/w I figured out how to do it. Just gotta find a way to connect the factory headlight power cable to the ballast (you can cut the wires and connect them) but I'm gonna get a harness for it.

even considered 75W but yeah, don't wanna go blinding people

Not 35W's not bright enough..