Results 1 to 7 of 7
  1. #1
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover

    O2 sensor wiring

    hey everyone
    can anyone wire up an o2 sensor to my ecu tomorrow?
    i need it done urgently.
    the wires are there but arent wired to the ecu
    i made an attempt last night but was unsuccessful.
    its an ek with p72 ecu, with b18 sir-g engine.
    let me know asap.
    not sure if i posted in the wrong section.

    pm or mobile 0422 082 681.

    cheers

    or any help would be appreciated.

    the o2 sensor has a green wire, yellow wire, and two blacks which have silver through them, so cannot distinguish which one is which, and was unable to find any info on the net.

    thanks

  2. #2
    Member Array
    Join Date
    Mar 2011
    Location
    Brisbane Qld
    Car:
    2 Tonne Ek Tank
    Do you just need to know the o2 sensor colour code?
    http://hiflo.com.au/pdf/O2%20sensor%...ur%20codes.pdf

    Or do you need the ecu pin outs? Let me know what obd series your ecu is and ill put up the pin out for you.

    Edit: Ill just put them up and you can pick which one your ecu matches.
    Obd 1
    http://technet.ff-squad.com/wiring.obd1.htm
    Obd 2a
    http://technet.ff-squad.com/wiring.obd2a.htm
    Obd 2b
    http://technet.ff-squad.com/wiring.obd2b.htm
    Last edited by TbM; 02-09-2011 at 10:01 AM.
    "I have no idols. I admire work, dedication and competence." - Ayrton Senna


  3. #3
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    Oh cheers man
    It's p72 obd2a
    Pinouts and wiring.

    I'll check it out when I get home

    Rep+1

  4. #4
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    Just not sure if they have used d series harness or b

  5. #5
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    Actually they were what we were using last night
    Doesn't have a white wire. It's yellow
    And where the pinouts are.. There's nothing there?
    So confused

  6. #6
    Member Array
    Join Date
    Mar 2011
    Location
    Brisbane Qld
    Car:
    2 Tonne Ek Tank
    Quote Originally Posted by CRXDEL501 View Post
    Actually they were what we were using last night
    Doesn't have a white wire. It's yellow
    And where the pinouts are.. There's nothing there?
    So confused
    I would assume the yellow is white so signal +, Where did you buy the o2 sensor from? They should be able to tell you the colour code if its not a normal ngk or denso one, could also test it with a multi meter or AFR gauge to make sure you have the wires right.

    The ecu pin out are linked in my last post i just put all the obd's i had up so you can pick yours. Heres the obd 2a one again.
    http://technet.ff-squad.com/wiring.obd2a.htm
    I think your looking for pins A6, A11, D7 and im not sure of the last one.
    Heres a link that may help, read some of the replies.
    http://www.ozhonda.com/forum/showthr...s-Code-41-PO2H
    "I have no idols. I admire work, dedication and competence." - Ayrton Senna


  7. #7
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    Thanks heaps mate
    Yeah I would assume it would be the white too
    Um I didn't get the o2 sensor and the seller I don't think is sure.
    I think we did do it wrong last night but needa figure it out
    I hate wiring lol

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.