-
Honda Integra Wont Start, just keeps cranking
Hey Everyone!
The problem:
i was driving the other morning to work and the car stalled on me on the freeway. now the car just cranks and doesn't 'turn over to drive'.
I was driving a Honda Integra GSI 1997 model.
i searched all over Google and OzHonda did what I've found and still nothing. was wondering how i could diagnose more to find the problem.
what i have done so far:
-put key in ignition, i hear the fuel pump priming. that (whining sound) that goes for 3 seconds.
-checked the main relay, all the joints seem okay, i've just soldered afew today and still nothing, will solder all when i get more light lol
-checked the fuses under the dash, all fuses seem okay, but will check again to make sure.
Hoping to check:
-Hopefully i will check to see if the engine is getting fuel from the fuel filter and
-check the spark plugs (but not quite sure how to go about it)
and looking into the distributor and ignition switch.
Anything else i could do?
Regards,
OJ
Last edited by Skyline_034; 04-05-2013 at 06:01 PM.
-
You didnt search hard enough.
Common problem is the coil inside the dizzy has gone - simple and easy fix. How many KM on your GSI?
Also please remove the advertising in your signature. It is not allowed.
Last edited by infurNOS; 04-05-2013 at 07:04 PM.
EG
-
![Quote](http://static2.ozhonda.com/forum/images/misc/quote_icon.png) Originally Posted by infurNOS
You didnt search hard enough.
Common problem is the coil inside the dizzy has gone - simple and easy fix. How many KM on your GSI?
Also please remove the advertising in your signature. It is not allowed.
On the GSI has about 240k km's.
Dizzy as in distributor yeh?
-
90% sure it is the coil inside the dizzy.
I have a spare working one, PM me if you want it.
-
![Quote](http://static2.ozhonda.com/forum/images/misc/quote_icon.png) Originally Posted by Skyline_034
On the GSI has about 240k km's.
Dizzy as in distributor yeh?
That is correct, mine went at approx the same KM! Would crank and crank and crank, just no spark. A lot of people replace the entire distributor ($$$$$) but it is not needed, mechanic job for the coil is not very expensive. There is a DIY available if you want to tackle it yourself.
Hope it gets resolved asap for ya
-
![Quote](http://static2.ozhonda.com/forum/images/misc/quote_icon.png) Originally Posted by MassiEk4
90% sure it is the coil inside the dizzy.
I have a spare working one, PM me if you want it.
thanks! ill let you know
![Quote](http://static2.ozhonda.com/forum/images/misc/quote_icon.png) Originally Posted by infurNOS
That is correct, mine went at approx the same KM! Would crank and crank and crank, just no spark. A lot of people replace the entire distributor ($$$$$) but it is not needed, mechanic job for the coil is not very expensive. There is a DIY available if you want to tackle it yourself.
Hope it gets resolved asap for ya
errr.. annoying. thats pretty much what's happening haha, crank crank crank and nothing.
ill test it out tomorrow hopefully.
this the DIY http://www.ozhonda.com/forum/showthr...-Lots-of-Pics!
-
![Quote](http://static2.ozhonda.com/forum/images/misc/quote_icon.png) Originally Posted by Skyline_034
Yeap - that's the one. You will not have any spark when you test tomorrow.
-
Happened to me as well. It was the Coil in the Dizzy like mentioned.
I bought my replacement from Repco for $38, it was a generic brand, Plenty in stock because it was compatible with a lot of other Honda's (CRV, Civics, Integra DC4/2/R etc etc). It was a piece of cake to Install.
無限 The Form is in the Function 無限
teamGROUNDzero
-
thanks everyone for your help!
it was the coil inside the distributor!
while trying to take off the rotor, it for some reason fell off (didn't knock it or anything...strange) so had to get a rotor + coil from repco.
very simple fix ![Teeth](http://static2.ozhonda.com/forum/images/smilies/teeth.gif)
thanks again everyone!
cheers OJ!
-
Green block gangster
Array
your problem was the rotor, if it was loose and you did not break it.
it sheered off, usually due to high temps in the dizzy from the bearing getting hot, possibly failing
-
Glad to see it was resolved. Thread closed.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Bookmarks