Page 1 of 2 12 LastLast
Results 1 to 12 of 13
  1. #1
    Member Array
    Join Date
    Nov 2003
    Location
    Hills District
    Car:
    EF Si

    CV boot replacement

    hey guys, wondering if there is a need to use genunie Honda parts for CV boot replacement.

    thanks.

  2. #2
    i just went down to a place called tuner enterprises, casue honda wanted like 200 bucks for two or something

    and i got a pair of non honda ones inner and outer both sides for 90 bucks :P and they 5 year warranty :P

    but no you dont NEED honda ones as long as they fit well and good quality


    i would suggest not getting the split boots becasue theses can fall apart and casue problems :P
    Last edited by lerroy; 03-11-2005 at 09:05 AM.

  3. #3
    TRAVDM Array
    Join Date
    May 2004
    Location
    BNE, Q
    Car:
    Lots of Hondas
    i have no honda ones on my car atm, outer boots only, they were like $11.00 each, holding up well for the moment
    oh wrd!

  4. #4
    Member Array
    Join Date
    Nov 2003
    Location
    Hills District
    Car:
    EF Si
    cool stuff, whats a outer and inner boot?

  5. #5
    Ones for the outer joint, the others for the inner joint.

  6. #6
    Inner boot is the the boot nearest the middle of the car or closest to the drive shaft bearings

    the outer is just before it connects to the wheel

    see below for link to team integra article
    but as i said dont get split one like the guy did in tyhat article there not as strong


    http://www.team-integra.net/sections...?ArticleID=839

  7. #7
    Member Array
    Join Date
    Nov 2003
    Location
    Hills District
    Car:
    EF Si
    mm.. very interesting, well ill be changing the outer CV boot, i read the DIY how do you do it if it's not spilt?

  8. #8
    Member Array
    Join Date
    Mar 2004
    Location
    Melbourne
    Car:
    DC5S but not for long...
    can u guys tell me what are these no name CV boots and where to get em? cheers and thanks

  9. #9
    i got them from a place on northern beaches
    http://www.turnerdriveshafts.com.au/

    but im sure alot of palces can sell u some, hannys etc..

    and yeah to replace you need to pull out the drive shaft to do inner and to do outer you need to remove the brake drum part so you can access behind it ( sorry my terms of parts is limited hehe)
    Last edited by lerroy; 03-11-2005 at 03:14 PM.

  10. #10
    Needs more time... Array
    Join Date
    Aug 2003
    Location
    Sydney
    Blog Entries
    12
    I think what lerroy means is that you need to take the hub nut / axle nut off and pop the drive shaft out to do the outer boot

    Hannys do both outer boots for about $100
    Got a question? Check out the FAQ - http://www.ozhonda.com/go/faq

  11. #11
    yeah thansk wyn :P

    its a dam messy job having to pack the boots again for 100 bucks i would recommend getting hannys to do it...well worth it unless you wanna learn or bored ehhe :P

    good luck

  12. #12
    Member Array
    Join Date
    Jun 2005
    Location
    Sydney
    Car:
    EVO IX
    i got my cv boots replaced at hanny's...
    they done good job

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.