-
[DIY] Installing the Comptech Icebox Air Intake Kit
Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk! If your car explodes it is not the fault of Ozhonda or me.
Aim: Install & fit the Comptech Icebox Intake Kit
Required: Socket Set
- That fit the bolts you want to take off.
- Extension Rod.
Screw drivers +/ -
Comptech Icebox Intake kit
- Icebox Lid
- High Flow Filter
- Inlet Horn
- Inlet Adapter
- Inlet Horn Bracket
- 2x #56 Band Clams
Steps:
1. People with 06 euro *like myself* read “http://www.ozhonda.com/forum/showthr...+mugen+bumper” for steps to undo front bumper in order to reach the bolts for the resonator.
2. For those who dont' take out the bumper, turn the steering wheel to the right, take out the fender liner and take off the 3 bolts holding the resonator like in the link in step 1.
3. Undo the clips for the inner fender, also the bolts around the front left bumper.
4. Assemble the intake pipe together by, sliding a #56 band clamp onto the inlet air horn (for Fender Bracket) and assemble lower inlet air horn with adepter attached using the remaining #56 band clamp at top and insert inlet air horn into the bottom of stock air box.
5. Position fender bracket inline with lower grounding bolt, and attach using stocking bolt in this location. Slide #56 band clamp over fender bracket and tighten in place.
6. Remove the stock lid and filter from stock intake box, by unscrewing the 4 bolts. If you use a extension rod with the stock set, trust me, makes the job much easier with the right tools.
7. Use the can of UniFilter oil to spray evenly on both sides. Let it sink into the foam so leave it for 3 minutes.
8. Install Comptech high flow filter into the stock air box, simply by just placing it on the air box where the old stock filter was, blue side facing down and yellow side up.
9. Remove spring band from stock inlet pipe. I find it super doper difficult to take off, so what I did was. Stick 2 screw drivers in, and under the spring then lift, and force it.
10. Place the icebox lid on top of the stock air box with the high flow filter in it. Attach stock inlet pipe to Comptech lid, make sure it is fully enclosed or else it will make a hissing noise while full throttle.
11. Start the engine, check for any unusual sound from the engine bay if some, then time to troubleshoot, can’t help you with that. If everything’s all good then, warm up the engine then trying out your new intake, also listen for vtec kicking in around 6000rpm, also feel what’s different & improve.
Here ares also 2 sound files of the oem intake and the comptech.that I recorded with my phone.
Before (oem): http://h1.ripway.com/Bustersonic12/Before.wav
After (comptech): http://h1.ripway.com/Bustersonic12/After.wav
Post your comment about the Comptech Air Intake Kit here, good or bad all welcome~!!
My comments are,
- faster acceleration
- smoother acceleration
- smoother rev
- feels less limit or resistant on the accelerator.
Just my own opinion, have not actually dyno yet, so all my opinion have not been confirmed yet if wrong please correct me.
Special Thanks to the people that helped me in removing the front bumper, and resonator, and people that gave me advices on the intake, thank you
PS: if you find this guide helpful, please + me points thanks thanks
IF U WANT PHOTOS OF THIS DIY, PM ME cos this post been up for a while all the links are broken
Last edited by BusterSonic12; 08-08-2007 at 10:13 PM.
'03 Integra DC5 Type R
Wakefield Park: 1:13.047 w/ street tyres
Eastern Creek Int'l Raceway: 1:57.969 w/ street tyres
Power: 155Kw with Mugen N1 ECU
-
Fast and furious? I drive slow and luxurious...
-
that's good to hear
got sound files too :P
Originally Posted by stephen8512
nice write up
'03 Integra DC5 Type R
Wakefield Park: 1:13.047 w/ street tyres
Eastern Creek Int'l Raceway: 1:57.969 w/ street tyres
Power: 155Kw with Mugen N1 ECU
-
Very nice, and pics of everything! Very nice...
--------------------------------------
Stocky CL9 - 1:17.2
-
I still love HONDA!
Array
how does the torque feel in the low range? a number of people I know felt torque isn't great in low range
-
well... i m not too pros into car... but i can sure feel a difference in the acceleration, not sure if it is just my mind playing tricks torque kinda the same, i think... not too sure... done this mod one month ago, now starting to get used to the car, so you just feel nothing.
Originally Posted by euro77
how does the torque feel in the low range? a number of people I know felt torque isn't great in low range
'03 Integra DC5 Type R
Wakefield Park: 1:13.047 w/ street tyres
Eastern Creek Int'l Raceway: 1:57.969 w/ street tyres
Power: 155Kw with Mugen N1 ECU
-
very good write up dude. great photos. would've been good if u could circle the areas involved so I dont have to look for them.
But + rep to you
-
Originally Posted by SiReal
very good write up dude. great photos. would've been good if u could circle the areas involved so I dont have to look for them.
But + rep to you
>.< my first write up, bit noob... sorry... try better next time hehe thx
'03 Integra DC5 Type R
Wakefield Park: 1:13.047 w/ street tyres
Eastern Creek Int'l Raceway: 1:57.969 w/ street tyres
Power: 155Kw with Mugen N1 ECU
-
Also mate, ur photos arent working. might wanna PM/email them to wyn, where he'll upload to OH server so u can have them permanently hosted Then u just have to redirectly the links in ur writeup.
-
nice writeup +PQ
did u still use the stock bottom part of the airbox?
if so, u only changed the snorkel and lid?
Gary
-
that's right, the bottom half of the air box is still stock.
Originally Posted by jdmlvn
nice writeup +PQ
did u still use the stock bottom part of the airbox?
if so, u only changed the snorkel and lid?
Gary
'03 Integra DC5 Type R
Wakefield Park: 1:13.047 w/ street tyres
Eastern Creek Int'l Raceway: 1:57.969 w/ street tyres
Power: 155Kw with Mugen N1 ECU
-
Originally Posted by euro77
how does the torque feel in the low range? a number of people I know felt torque isn't great in low range
Well done Bustersonic!
Euro77 - you definately lose some torque down low. I have a couple of times put back on my stock lid with OEM filter and immediately notice that extra torque down low. Waiting for Hondata to sort that out!
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Bookmarks