-
Hey Spoon, so what power is it pulling?
-
Originally Posted by urxqsd
Hey Spoon, so what power is it pulling?
133kw atw @ 8,000rpm & 208Nm torque @ 6,200rpm
Not too shabby for OEM Honda rebuild.
Last edited by Spoon SiRG; 22-12-2013 at 07:24 AM.
I SiR = Sport injection Racing
-
very nice, not sure if should do headwork on my B16a2 or just leave it and collect a heap of parts to build B18 from scratch,
What Intake and TB you running? got some cam and springs and crap coming along with edelbrock intake but not sure if guna put on, if i spend all the extra cash for bolt ons and headwork i figure a new bswap is in order, only issue is my b16 has 16xxx since rebuild so would be a waste to swap it out. thoughts?
Last edited by urxqsd; 27-10-2013 at 09:54 PM.
-
How did the motor look when your tore it down??
My b18c2 seems to be using a lot of oil too..although I did a comp test n got good consistent numbers accross all cylinders. Wondering if my motor is starting to die on me..but like yours still pulls hard.
-
Originally Posted by urxqsd
very nice, not sure if should do headwork on my B16a2 or just leave it and collect a heap of parts to build B18 from scratch,
What Intake and TB you running? got some cam and springs and crap coming along with edelbrock intake but not sure if guna put on, if i spend all the extra cash for bolt ons and headwork i figure a new bswap is in order, only issue is my b16 has 16xxx since rebuild so would be a waste to swap it out. thoughts?
Depends on what you're after, B16A has the ability to produce more power on higher revs, just doesn't make the low end torque a B18C makes. I'm using an OEM 62mm ITR Throttle Body w a Skunk2 IM. Yeah you can swap in some other cams & valvesprings in your freshly rebuilt B16A to make more power.
I SiR = Sport injection Racing
-
Originally Posted by vti_ek9
How did the motor look when your tore it down??
My b18c2 seems to be using a lot of oil too..although I did a comp test n got good consistent numbers accross all cylinders. Wondering if my motor is starting to die on me..but like yours still pulls hard.
Overall the engine internals were good for a 133t km engine, with the exception of the 4th Connecting Rod Bearing which was badly scored. Oil consumption can come from the following areas:
1. Gasket/ Seal Leaks
2. Worn Valve Stem Seals
3. Piston Rings
Last edited by Spoon SiRG; 22-12-2013 at 07:29 AM.
I SiR = Sport injection Racing
-
Originally Posted by Spoon SiRG
133kw atw & 208nm torque.
Not bad. What else did you change in your build that isn't stock?
-
Originally Posted by Spoon SiRG
Depends on what you're after, B16A has the ability to produce more power on higher revs, just doesn't make the low end torque a B18C makes. I'm using an OEM 62mm ITR Throttle Body w a Skunk2 IM. Yeah you can swap in some other cams & valvesprings in your freshly rebuilt B16A to make more power.
Main reason for car is to have fun on the track, just want that little bit extra poke when i need it. looking at final drive aswell at the moment. it allegedly has CTR pistons in it all ready, was rebuild when i bough it, very clean motor.
guess its guna be trial and error for now till i find the balance i like..
-
Originally Posted by rc_
Not bad. What else did you change in your build that isn't stock?
Just the usual bolt-on's: Mugen Intake, Skunk2 IM, Z-Speed Camgears, DC Sports JDM 4-1 Header (2.5 Inch Version), Spoon Street Muffler to shut it up, Tuned via Apexi Power FC ECU
Everything else is OEM Honda.
I SiR = Sport injection Racing
-
Damn that's good numbers for such minimal mods. Who did the rebuild? Motor must be nice n tight..
-
Originally Posted by vti_ek9
Damn that's good numbers for such minimal mods. Who did the rebuild? Motor must be nice n tight..
Had a bit of help from an ex-Honda master technician
Yes it is crucial to check & measure clearances/ tolerances when assembling an engine to ensure it lasts & makes power.
I SiR = Sport injection Racing
-
I have 2 sets of SL valves springs here now Mr
The life of a 4 stroke engine
It sucks it squeezes it bangs it blows
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Bookmarks