Page 1 of 2 12 LastLast
Results 1 to 12 of 19

Thread: boot leak

  1. #1
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover

    boot leak

    just got a boot leak in my crx.... i found water in the two corners near the tail lights and this morning there was moisture all along the top of the boot..

    i have taken the spoiler off and plugged the holes and used silicon to seal them, and also have put a type r badge on and there is a real slight gap, only just noticeable up the top of the badge, not sure if this could be the problem.

    checked all my seals along the boot and they appear to be fine...

    anyone else know what it could be?

    just dont know where to start.

  2. #2
    Member Array
    Join Date
    May 2006
    Location
    Brisbane
    Car:
    380GT,XTrailSTR
    the rear light housings, either change the rubber seals under them or sikaflex the gaps to the chassis
    Quote Originally Posted by Slow96GSR
    If 1 person has had bad luck with a product don’t condemn it until you yourself have tested it. Now if 10 pros have tried it and it sucked then I would trust their opinion.

  3. #3
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    both top and bottom?

    i have noticed there is a bit of a gap up the top of the light between itself and the body

  4. #4
    Member Array
    Join Date
    May 2006
    Location
    Brisbane
    Car:
    380GT,XTrailSTR
    Quote Originally Posted by CRXDEL501 View Post
    both top and bottom?

    i have noticed there is a bit of a gap up the top of the light between itself and the body
    i've only done top and sides and changed the seal underneath since it came with the aftermarket lights. didn't bother with the bottom as i don't se water going upwards anytime soon

    i'll try take pics.
    Quote Originally Posted by Slow96GSR
    If 1 person has had bad luck with a product don’t condemn it until you yourself have tested it. Now if 10 pros have tried it and it sucked then I would trust their opinion.

  5. #5
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    still cant find the leak... there has been moisture on the top of the boot early in the morning.

    i put silicon over my badge coz there was a slight gap, still havent put silicon in the gap about the tail lights.

    if it was the tail lights wouldnt it be wet behind them???

    it hasnt been its just been wet in the corners of the boot near the tail lights...

    if i cant find it, where should i take it to get looked at???

    just panel beater somewhere local to me?

    cheers

  6. #6
    Member Array
    Join Date
    May 2006
    Location
    Brisbane
    Car:
    380GT,XTrailSTR
    take one of the tail-lights out and you'll see the seal i'm talking about.. it's 4 bolts/nuts...


    Quote Originally Posted by CRXDEL501 View Post
    still cant find the leak... there has been moisture on the top of the boot early in the morning.

    i put silicon over my badge coz there was a slight gap, still havent put silicon in the gap about the tail lights.

    if it was the tail lights wouldnt it be wet behind them???

    it hasnt been its just been wet in the corners of the boot near the tail lights...

    if i cant find it, where should i take it to get looked at???

    just panel beater somewhere local to me?

    cheers
    Quote Originally Posted by Slow96GSR
    If 1 person has had bad luck with a product don’t condemn it until you yourself have tested it. Now if 10 pros have tried it and it sucked then I would trust their opinion.

  7. #7
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    so your prety certain its the tail light?

  8. #8
    Member Array
    Join Date
    Sep 2006
    Location
    Perth
    Car:
    Honda CRX
    yeap... do change the rubber seal tat is btw the tailight........then the problem will be solve....

  9. #9
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    where can i get new seals or rubber from?

  10. #10
    Member Array
    Join Date
    May 2006
    Location
    Brisbane
    Car:
    380GT,XTrailSTR
    Quote Originally Posted by CRXDEL501 View Post
    where can i get new seals or rubber from?
    Honda spare parts department in Penrith if your in Syd... order only item though and will cost an arm and leg.

    Cheaper option is take both of them out and get 4mm foam mats from Clark rubber at ~$7ea for a 30cm by 30cm.. or spen ~$100+ for aftermarket tail lights....
    Quote Originally Posted by Slow96GSR
    If 1 person has had bad luck with a product don’t condemn it until you yourself have tested it. Now if 10 pros have tried it and it sucked then I would trust their opinion.

  11. #11
    Member Array
    Join Date
    Feb 2007
    Location
    SydN3Y
    Car:
    your mum
    as mentioned it is most likley your taillight gaskets, it seems to be a common problem. just go to clark rubber enough rubber foam and trace same shape of the oem. the ones you can get at clark rubber are slightly thicker which is better at sealing around the taillight hole, but dont get it too thick to make your taillights stick out.

  12. #12
    Member Array
    Join Date
    Feb 2008
    Location
    Orange county
    Car:
    Pimpin rover
    yeahhh i took it to a panel beater today, and he said because there is moisture sitting up the top of the boot, it has to be coming in thru the spoiler plugs.. i took all my carpet out, and just cant see any running marks, if it was coming thru the tail lights :S.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.