4-2-1 headers, what brand is good at reasonable price??

**mpd076-chuck** · 04-03-2007 05:15 PM

dc2rrrr, I thought you of all people would know that not all headers, cat's and b-pipes match perfectly. If Adrian suggested one and you decided to go it alone, why compain publicly? You didn't have to buy his cat anyway, just get the dimensions you need. It's just annoying when people publicly complain like this, because when I spoke to Adrian about getting a Toda header, the first thing he said was you need to make sure it will fit with your cat. I'm sure he would have done the same with you...

**dc2rrrr** · 05-03-2007 06:45 AM

The cat had nothing to do with it as I had a jdm cat. Who cares im over it.
Only reason I even posted was because he was baggin Dave and then said toda ones fit perfect yet mine didnt. And for $1400 one would expect it to.
I will shut up now SSSSHHHH

**Benson** · 05-03-2007 08:56 AM

haha 1400? damn thats exxy dude... why not get normal jdm 4-1, they make relatively the same power for like 400 bucks and is a more perfect fit... haha

Yeh dave's headers a elite, worth the money and yeild much more gains. Some people need to go figure cost vs power gains before purchasing there headers.

dc2rrr sounds like you need a new set of headers hahaha.

**todas**t** · 05-03-2007 10:37 AM

Originally Posted by Benson

haha 1400? damn thats exxy dude... why not get normal jdm 4-1, they make relatively the same power for like 400 bucks and is a more perfect fit... haha

Yeh dave's headers a elite, worth the money and yeild much more gains. Some people need to go figure cost vs power gains before purchasing there headers.

dc2rrr sounds like you need a new set of headers hahaha.

dc2rrr needs a whole new motor........

**TODA AU** · 05-03-2007 12:13 PM

Originally Posted by dc2rrrr

The cat had nothing to do with it as I had a jdm cat. Who cares im over it.

Yes you did have a JDM cat. That was my point exactly. You had a 98 Spec JDM cat.
Hence, at your request you have 98 Spec headers to suit & this is precisely why the rear bracket does not align.
You knew this at the time & didn’t have a problem with it.
Normally we supply the 96 Spec header, where rear bracket alignment is not an issue.

Regarding you having a problem with us,
If you had a real problem with your car,
You would have been in contact with us to have it rectified. – Not the case.
Further, you could have also contacted the MVIRA & had a mediator appointed to air your problem & have the issue rectified
Again, this is not the case.
That said, I suggest you aught watch what you say.

Originally Posted by Benson

haha 1400? damn thats exxy dude... why not get normal jdm 4-1, they make relatively the same power for like 400 bucks and is a more perfect fit... haha

The JDM 4~1 header is the 98 spec header.
The rear bracket does not line up.

**DynoDave** · 05-03-2007 02:10 PM

Very interesting and disappointing thread this one

OzHonda members you have all really shown your true colours yet again.
Regards Dyno Dave

**JDMtoy** · 05-03-2007 02:30 PM

i can feel the love.

**xtercii** · 05-03-2007 02:33 PM

Hey Dave's back on this forum!!

**Lukezen27** · 05-03-2007 02:42 PM

Originally Posted by DynoDave

Very interesting and disappointing thread this one

OzHonda members you have all really shown your true colours yet again.
Regards Dyno Dave

Then hopefully you read this

Originally Posted by Lukezen27

Now that Dave’s been doing a bit of research on SOHC VTec’s mes thinks there must be a nice D-series header somewhere in the mix lol
And maybe if where lucky some nice info on SOHC VTec mods and tweaks
Or is he over the whole thing? Hope not
LukeZen

Anything on the SOHC VTec front?

Oh and I just PMed you

LukeZen