Page 4 of 4 FirstFirst 1234
Results 37 to 45 of 45
  1. #37
    Member Array
    Join Date
    Mar 2006
    Location
    Sydney, Hills area
    Car:
    04 Euro 6mt
    nope, its realy easy, onli hard part was the U-clip that he was talkin bout realli hard to get off, at 1st i was too scared to force incase i broke stuff, but by the end i was using a hammer LOL (mine was really really stiff lol and didnt have any plyers)

  2. #38
    Member Array
    Join Date
    Aug 2004
    Location
    Sydney Harbour Bridge
    Car:
    03 CL9 Euro
    ROFL,
    HAMMER only time i used a hammer was when i had to put the mugen u clip back in cause it'd fit half way then jams up.

    But yeh i was scared i'd burr the U clip when prying it out.

    So you mean there is no need to jack up the car or anything? Sounds good...mmmm.
    Piss easy mod.

    BTW only thing is that sometimes i get my finger caught in between the shift knob and handbrake lever when i put into reverse as my shift knob i have is circular in shape.

    ENKAY did you end up removing the stock shift knob clip thing?
    As i have now after i removed i replaced the assembly.
    vTeK 4-Life!
    FOR SALE: CL9

  3. #39
    Ninja turtle Array
    Join Date
    May 2004
    Location
    Sydney
    Car:
    Chloe
    No need to jack the car, everything you need to touch is under the gearknob.
    --------------------------------------
    Stocky CL9 - 1:17.2

  4. #40
    Member Array
    Join Date
    Aug 2004
    Location
    Sydney Harbour Bridge
    Car:
    03 CL9 Euro
    did you guys have any problems with the ashtray light not switching on?

    Might be the connection which i need to re-adjust or something as it was working before the install.
    vTeK 4-Life!
    FOR SALE: CL9

  5. #41
    Member Array
    Join Date
    Feb 2005
    Location
    Brisbane
    Car:
    09Euro, 08CR-V
    Hi:
    congratulation on your new Short shift.

    I just went back to the thread where we had our Comptech short shift installed.
    http://www.ozhonda.com/forum/showthr...ift#post291588
    If you scroll down a bit, there is also a photos there showing our team effort. It's good to relive that memory..

  6. #42
    Member Array
    Join Date
    Jan 2008
    Location
    House
    Car:
    RA109 / BGP001
    i am going to purchase one of these. this week or next.

    is it simply taking off the old part and putting on the new?

    does it come with a knob ?

  7. #43
    Member Array
    Join Date
    Aug 2004
    Location
    Sydney Harbour Bridge
    Car:
    03 CL9 Euro
    i am going to purchase one of these. this week or next.

    is it simply taking off the old part and putting on the new?

    does it come with a knob ?
    yeh pretty much, most of the stuff you reuse only thing that would be left over is the stock U clip + stock assembly itself, no shift knob imagine if they did have one would be hella expensive.

    hope this helps.
    vTeK 4-Life!
    FOR SALE: CL9

  8. #44
    Member Array
    Join Date
    Jan 2008
    Location
    House
    Car:
    RA109 / BGP001
    helps heaps thanks crapdaz

    what about gearbox. does short shifter have any negative impacts on the gearbox?

  9. #45
    Member Array
    Join Date
    Aug 2004
    Location
    Sydney Harbour Bridge
    Car:
    03 CL9 Euro
    what about gearbox. does short shifter have any negative impacts on the gearbox?
    your gearbox assembly is replaced, with the shorter mugen one. Pretty much direct bolt on everything is installed within the cabin.

    Regards,daz
    vTeK 4-Life!
    FOR SALE: CL9

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.