head gasket

[Lukezen27]

never leaked water into the oil????but it was lyk there was a pressure build up from the motor into the cooling system

that's what mine did

My HG went from overheating not boost

New OEM HG and ARP studs at 70+

All seems good with my setup

if yous want more info on were i went wrong the motor belonged to weq( yep thats right its his old motor) when adrian tuned it he said that it was to rich and leaned it out

http://www.ozhonda.com/forum/showthread.php?t=36946

this is what happened last time he built it

Oh dam Weq block was ****ed from what I've head after Weq passed it on

Cheap is not always cheap sorry bro but if the blocks the problem then you will just keep blowing HG

[Limbo]

luke - your supose to gime your guy's contact so i can get mine done later, wanna get the arp bolts also

[Lukezen27]

luke - your supose to gime your guy's contact so i can get mine done later, wanna get the arp bolts also

You know Robert at hannys 02 97255115

[TEGZOTIC]

get a metal headgasket (cometic, cosworth if your on a budget) otherwise a apexi or something if they make it for that engine... but u must get some arp headbolts, they are the reason y headgaskets blow, and temperature ofcourse

[Limbo]

o bugger than your gonna have to come talk to him with me also

[myztery]

its already got head bolts for it done some researching and found out that the head was over shaved so the sleeves ended up sinking in, f***ed up hard so i thought about it.... and i've come to the conclusion that the only way to fix the problem is to replace the block (cos of high compression ) i might loose compression but at least ill save headgaskets... and i might just take it the only one that knows the motor inside out...DD

[Lukezen27]

its already got head bolts for it done some researching and found out that the head was over shaved so the sleeves ended up sinking in, f***ed up hard so i thought about it.... and i've come to the conclusion that the only way to fix the problem is to replace the block (cos of high compression ) i might loose compression but at least ill save headgaskets... and i might just take it the only one that knows the motor inside out...DD

You seemed to have answered your own question..

Blocks ****ed and you will keep blowing HG

Hence the reason no one bothered buying this setup even at a hell cheap price..

o bugger than your gonna have to come talk to him with me also

Yeah I'll come talk to him but I'm not sure it will help...

Robert hates boosted Honders and only works on mine coze he re-built my D16Y1 before I was turboed lol

[myztery]

from a bit of your guys info i was able to cross out things
and find out a little about my own engine cheers boys for the info....

[Weq]

From what i heard down the grape vine, the block needs sleeves. Too many overheats. 122kw on 5.5psi is about on par with what i made on it.

[myztery]

it needs more than sleeves it needs a whole new block you must of got the info from the wrong grape vine (stale)

[ILZ]

hey everyone i have a d16y1 turbo setup

i was hoping i could get some info please first of all what is a better than a oem 3 layer copper coated head gasket... i've been told that a stainless steel gasket should do the job,,,,,if any one can help where i can find this gasket???? and if anyone knows anything about them ( by the way i blew the head on the dyno 121.4kw at 5.5 pound )...not much for a fully worked motor...

much appreciated for knowledge...

a mutli-layer shim gasket will be fine, i run a genuine honda gasket in my car,this engine has seen 35psi boost and and well over 60 low 10 sec passes.
i suspect it blew coz of the tune or the head wasnt fitted correctly