Results 1 to 12 of 18

Threaded View

  1. #1

    DIY: Steering Rack Boot Replacement (EG Civic)

    Disclaimer: The following is provided as a GUIDE ONLY, and neither myself nor Ozhonda take any responsibility for the outcomes of someone else doing the following. You follow these steps at your own risk!


    Hey everyone,
    Thought I would write up a DIY on how to change the steering rack boots for an EG Civic. This is a common issue on old and weary cars where the steering rack boot splits and in my case completely broke in half. Not replacing the damaged boots can result in dirt and grime getting into the rose joint of the tie-rod and even into the steering rack itself. This can cause lots of play in your steering and in worst cases damage to the internals of the steering rack.


    Aim: Change front steering rack boots for 93 Honda Civic. This guide should be similar for most models around this era.

    Required:

    New rack boots
    Bearing Grease
    22mm Spanner
    17mm Spanner
    Side Cutters
    Pliers
    Hammer

    Step: 1
    Jack the front of the car up securely and safely, use Jack stands and remove the front wheels

    Step: 2

    Mark the tie-rod end nuts position and then loosen with 22mm spanner.



    Step: 3

    Remove the split pin from the tie-rod end ball joint. Loosen the castle nut with 17mm spanner. Do not unscrew all the way, just til the end of the ball joint.



    Step: 4

    Grab your hammer and hit the end of the hub carrier to loosen the ball joint. Note: Do not strike any part of the ball joint or tie-rod end.


    Step: 5

    Once ball joint is loose you can remove the castle nut from the ball joint, lift the tie-rod end out and unscrew it from the tie-rod itself. At this point you can also remove the 22mm nut.




    Step: 6

    Once removed, check for play in the tie-rod end ball joint and clean then put aside.



    Step: 7

    Next, remove the damaged steering rack boot. Remove the small air tube first. You will need your pliers to remove the metal clips and metal cable tie of the boot. Abit tricky at first but just use a little extra force. With the metal cable tie securing the inner boot end I just cut it up with the side cutters seeing as it was nearly impossible to remove and the new boots were supplied with plastic cable ties anyway.




    Step: 8

    Bin that dirty ass shreaded boot and then clean up the tie-rod & steering rack with a cloth. Grab your bearing grease and apply a decent amount to the rose joint of the tie-rod. Once you're happy with that grab the new steering rack boots.



    Step: 9

    Apply the cable tie loosely to the inner end of the boot. Fit the boot over the tie-rod. Position the boot and then pull the zip tie tight and cut with side cutters. At this stage re-fit the small air-tube for depressurization.
    You can also cable tie the outer boot end now too.



    Step: 10

    Screw 22mm nut back on to tie-rod to marked position.
    Screw tie-rod end back on.
    Re-position ball joint into hub carrier and give it a hit with a hammer to get it in nice and tight.
    Screw on 17mm castle nut, tighten and re-fit split pin for security.




    Step: 11

    Repeat for other side and fit your wheels back on and you're done. Next hit VTAK haha just kidding.




    Caution: I would recommend you get a wheel alignment just for added safety.


    Last edited by dorikin; 23-11-2008 at 11:07 AM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.