Gt2876r

**Lukezen27** · 10-03-2009 06:09 PM

Originally Posted by Limbo

thanks that was a good read.
Fingers crossed it works that way when i put it on the car

Hey Hao

My Garrett rear dose have a part number .86 T712

**Limbo** · 10-03-2009 06:26 PM

http://www.turbobygarrett.com/

Judging by what i've seen it looks like an RS front - goto the link above for the measurements.
http://www.turbobygarrett.com/turbob...48_1_5_new.pdf

The rear is an .86 which will make it laggy, from what i'm reading

You have to rem only a few companies actually make turbo parts.

If you can change to that .64 rear i told you about it would be good.

The 60,71 & 76 have the same rear but each one has a larger front compressor, which will give it abit more lag on spool.

Hopefully due to the smaller inlet and exhaust mine will still spool in the 3-4krpm mark

**Lukezen27** · 10-03-2009 06:54 PM

So now I need to find a .64 rear cheap lol

**destrukshn** · 10-03-2009 07:07 PM

pm sent luke.
=)

**Lukezen27** · 10-03-2009 07:24 PM

Originally Posted by destrukshn

pm sent luke.
=)

Sold

**votek** · 10-03-2009 11:57 PM

well the gt2876r is not meant for our engines, its meant for engines where 3 cylinders feed a turbo which feeds 6

and in most cases very laggy

**Limbo** · 11-03-2009 08:19 PM

i'll see how we go, since it a hi comp turbo, we'll see if its laggy

**lookingforboost** · 14-03-2009 11:35 PM

well the GTiR pulsar from the factory runs a T28 with a .86 rear housing and they are non ball bearing builds boost and has full boost by about 3600rpm and the B16 having a more rev happy nature will make this turbo boost up fast anyway as the pulsar could only rev to 7000 rpm so the meat of the turbo will still be in the rev range for the B16

**Limbo** · 15-03-2009 12:59 AM

its a smaller t28, T2560 if i rem rightly, also its a low comp engine, its too hard to compare it to a b16.

I think you've missed the point of what i was looking at. But going by other setups & talking to people with something similar, looks like this turbo will boost at around 4krpm & will be a happy power maker

Originally Posted by lookingforboost

well the GTiR pulsar from the factory runs a T28 with a .86 rear housing and they are non ball bearing builds boost and has full boost by about 3600rpm and the B16 having a more rev happy nature will make this turbo boost up fast anyway as the pulsar could only rev to 7000 rpm so the meat of the turbo will still be in the rev range for the B16

**lookingforboost** · 16-03-2009 07:19 PM

Originally Posted by Limbo

its a smaller t28, T2560 if i rem rightly, also its a low comp engine, its too hard to compare it to a b16.

I think you've missed the point of what i was looking at. But going by other setups & talking to people with something similar, looks like this turbo will boost at around 4krpm & will be a happy power maker

Nar the GTiR used the largest of the factory T28 turbos and ran the .86 rear housing the T2560 is a different turbo completly and yes it is a low comp motor using a 8.5.1 i cant remember for sure.

the point i was trying to make was that the .86 is used on another 4cyc motor and isent that laggy

higher comp motor plus a ball bearings make it a faster spooling turbo that wont cause much problems with lag