ED6 The Saga Continues

[SHOGUNOVDDRK]

off topic but isaw u 2day shogun... at that portugese chicken place... i was the white guy standing there waiting by the wall... i didnt realise it was u till i saw u lean forward for sumthin and i saw ur tat on ur arm lol

hahahahaha-

Frangos.

Dude, there was a massive crowd of people, alot white.

haahahaha, Next time you see me give me a shout man

I work @ the Modern building directly across the road.

[tseesinngwailo]

See Shogun? This has all been caused by YOU!!! I should make you come and wire this up blindfolded while I jab you with a sharp bit of wood...

[SHOGUNOVDDRK]

BUT you wanted to do this, I'm just your sub-conscious.

[tseesinngwailo]

Shogun, I hope you are not my sub-concious...

I have a WTB thread as I am going to need bits to finish this off.
http://www.ozhonda.com/forum/showthread.php?t=117110

Will go to PnP tomorrow to get a loom and fuel filter, but still need an external pump for now until my EF9 tank with pump arrives from Japan.

Will be doing some wiring tomorrow and hope I can at least get the car to crank, the wiring could get a bit messy to start with..

Cheers
Tseesinngwailo

[SHOGUNOVDDRK]

bwuahahahahhaaha.

I lost my license....



And the Car got defected....

GG, looks like I'll be working on the new shell soon and doing a conversion...

[tseesinngwailo]

bwuahahahahhaaha.
I lost my license....
And the Car got defected....

GG, looks like I'll be working on the new shell soon and doing a conversion...

You WHAT???? what were you doing? and after your epic QLD trip, well, on a good note, I can supply you lots of advise on a swap hahaha

Now I can get some back! You new shell wont be happy until its a MOTUL replica

Hmmm, now theres an idea for my next car.... nah, the S600 is my dream, a sunny day, the roof down, wind in my.. oh wait...

[SHOGUNOVDDRK]

You WHAT???? what were you doing?

Nothing stupid Chris, had a missing p-plate.

Was driving my sister home from the shops ffs.

Car isn't getting un-defected, what is going to happen was going to happen in november anyway

Now I can get some back! You new shell wont be happy until its a MOTUL replica

no, but it will be satisfied with British Racing Green

[tseesinngwailo]

Hi All,

Well, I now have a fueltank with an EK injection fuel pump installed, I followed Peter's great build thread, and very carefully drilled my tank.

I will post pics later tonight and more info on what I have been doing, but have had major wiring issues.
Wiring help thread is here, I hope someone can help!
http://www.ozhonda.com/forum/showthr...11#post2406911

[SHOGUNOVDDRK]

Go Chris!!!!!!!!

[tseesinngwailo]

Hey All,

Well, here is what I have been up to lately...

DISCLAIMER: Just because I did this and didn't blow myself up, doesn't mean it can't happen to you, OZHONDA and myself hold NO RESPONSIBILITY for DIY work you perform using instructions you find on this forum.

Seeing as I was having a bugger of a time finding a tank with fuel injection pump (like a CRX) I decided to do what Peter did and drill mine..

I went to Pick-n-Payless and found an EG pump that Peter was good enough to pull out and leave on the back seat (thanks Peter) and on a return trip found a newer EK so took the pump out of it.

Grabbed the wiring loom from the ECU to the engine bay and injector loom, a genuine Honda jack (with bag) and a throttle cable, also found a good condition set of mudflaps (F + R) for my DA Teg too!

My little haul of bits



I needed a jack for the car, found this shiny one, just need to spot a handle now



The EK pump, really good condition



The mudflaps, should be on by this weekend



So, then I got started and pulled the tank out, then washed with soapy water (car wash soap) dried, and then washed again



Marked the hole using the gasket as a guide



Drilled the first hole


The EK pump and the foamy stuff used to fill my tank with soapy water



Then used a jigsaw to cut the hole, was more worried about the water/electricity thing than the fuel vapour, kept the tank full of soapy water to lessen the chances of fuel vapour problems



Theres always time for VITA



Dried out the tank again



Put the bolts in, using copper washers on the inside of the tank to seal the bolts, and threadlock on the outside to help make sure they dont come loose..



The pump in and looking factory lol



The mess of piping from the fuel tank,



Connected 2 of the lines together as they wouldnt be needed now I have the other pump in place

[SHOGUNOVDDRK]

Good stuff

[tseesinngwailo]

I had a lip on my 91 DA Teg front bar, which I found matches perfectly to the ED front, only problem is that the sides are longer, something that a hacksaw should be able to fix easily enough.. some of the bolt holes across the front fit too, this is an easy upgrade





This is the difference with the sides, the small gap you can see is just me holding the side up, it does actually pull into place and the profile matches perfectly, the width and radius are the same as the Teg, no cut in the middle either