-
problem with eg with b18c7
Hi all,
i just done the swap from B16a to B18C7 in my civic eg
currently i have problem with the wiring room and idel on the car,
i am use obd1 hondata s300 ecu to run my b18C7,
do i need to rewire the ecu room again or just plug and play,
i did try to start the car with the wire as is, but the S manager detect that there are 3 error code with the car,
1 ELD
2 knock senser
3 os heater senser,
what's the best way for me to do it?
i am thinking to buy 2 harness conversion to conver my my room, one is obd1 to obd2a and then plug another one from obd2a to obd1 again, i know i sound stupid, but any other way to do it, some people told me just by pass it, but i want to do it in the correct way (no by passing), no engine check light will on )it's on atm.
also another way is to change the obd1 plug to obd2a and just buy one harness conversion to run the hondata,
either way i can run both stock b18c7 ecu and hondata
also i think i might have vaccum leak, is this why it cannot idel probably?
can anyone confirm with that do i need to rewire again or just plug and play
any help would be great
thanks
-
is the s300 tuned for this motor?? why dont u try the stock ecu.
JDMYard Eg civic lsvtec 1.04:1 WAKEFIELD PARK
Bel Garage Dc2r/Neptune ecu
SUPERLAP 2010 clubsprint FF na winner
1.54.81 street tyre
-
I think you should just try to rewire instead of cramming in 2 patch harnesses. Much neater if you just made it up or pay someone 300 bucks to wire it in. Best to sort out the wiring first before multitasking with the idle as the wiring might be cause of the idle. As jdmTYPE R mentioned check to see if the hondata was coded to a b18c7.
-
The s300 is not tuned yet, using the ITR bacis map from the S manager, i need to buy the harness conversion first in order to run the stock ecu, but instead pay 200+ so i though it's better for me to buy HONDATA (that's what i think)
in the S manager, it's only says ITR map, so i though that's should be what i am using right, or i should look for the code of the ecu to lod it into the hondata?
anyone in Melbourne can conver the OBD1 to OBD2A, please pm me, as i think this way is better for me
thanks for the reply guys, thanks
-
Originally Posted by skyfrank85
i did try to start the car with the wire as is, but the S manager detect that there are 3 error code with the car,
1 ELD
2 knock senser
3 os heater senser,
what's the best way for me to do it?
And it sounds like you're nearly there...
Go into the S-manager software & turn off the problem errors.
That is ELD, Knock sensor, O2 heater & probably Barometric pressure & injector error.
See where you're at after that,
TODA Performance Australia Pty Ltd
TODA Racing - FIGHTEX - MFactory - HALTECH - EXEDY
Race engines, Dyno tuning, Licenced workshop, Parts.
P:0401869524 email: toda@todaracing.com.au
-
Originally Posted by TODA AU
And it sounds like you're nearly there...
Go into the S-manager software & turn off the problem errors.
That is ELD, Knock sensor, O2 heater & probably Barometric pressure & injector error.
See where you're at after that,
i did disable 3 of them,
but comes up another one which is the TDC, top dead centre sensor,
and the engine is running super rich at idel, lots of black smoke comes out, and fuel
check is the TPS, it's good, but now it's TDC that got me worry,
-
Green block gangster
Array
-
Hi ecu man,
how do i get it out of limp mode?
buy replace TDC sensor?
the workshop test the TDC, and it's working fine,
would a tune of the ecu fix this problem (i mean running rich)
or really i need to sort it out the tdc problem?
thanks
Last edited by skyfrank85; 12-11-2009 at 09:52 PM.
-
btw, today i did another run on the engine,
but disable all the eld, KS, O2, Barometric pressure & injector error
but the car is still eunning rich, however, TDC error did not come up
but instead come up with code 41 PO2S, would this is because the car is running too rich and it's out of the reading range for the O2 sensor?
any idea of whats goin on with the engine
also another thing is that i didn't connect the EVAP on the engine, would this creating any problem?
-
Green block gangster
Array
you need to wire it up right,
simple as that.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Bookmarks