FD/FN2/EP3 Wheel Setup Guide

[butterfingers]

any one know the width and offset for 17" that i would need to get if i run spoon cailpers for ep3 ?

17x9 +38 up front.

cr kais. dish rims can be different as offset and width do not neccesarily indicate clearance.

[Icebox]

17x9 +38 up front.

cr kais. dish rims can be different as offset and width do not neccesarily indicate clearance.

im thinking of ce28s 17x 8 +30 would that work?

[butterfingers]

im thinking of ce28s 17x 8 +30 would that work?

It should. I have a 50c coin width of clearance from caliper to spokes without extended studs and a 5 mm spacer

Before the 17" I had 18x7.5 cr Kai +48 offset which cleared (just) the calipers with the same spacer and extended studs so I'm sure ce28 will. Their quite concave once you get to 8" with with some decent offset

[Icebox]

It should. I have a 50c coin width of clearance from caliper to spokes without extended studs and a 5 mm spacer

Before the 17" I had 18x7.5 cr Kai +48 offset which cleared (just) the calipers with the same spacer and extended studs so I'm sure ce28 will. Their quite concave once you get to 8" with with some decent offset

what 17s were you running if you dont mind me asking so i know what width and offset i need to be looking at

[Perry]

what 17s were you running if you dont mind me asking so i know what width and offset i need to be looking at

17x8 +35 will clear but it depends on wheel design as well.

[Icebox]

17x8 +35 will clear but it depends on wheel design as well.

Awesome, gives me some ideas for wheel specs i need for my next set up

[butterfingers]

what 17s were you running if you dont mind me asking so i know what width and offset i need to be looking at

old set up Cr-Kai 18x7.5 +48 all round with a 5mm slip on spacer. the spokes ran flat against the caliper with like 2-3mm of clearance if that.
current set up Cr-kai 17x9 +38 with the same 5mm slip on spacer. same clearance as above close to the hub, however as the spokes go out toward the lip, it arches out giving more clearance from the middle of the caliper (where "spoon" is printed).

with the 17x9s i could just clear it without the spacer, but i was running extended studs, so the spacer was required to fully thread the wheel nuts.

hope that helps fellow ep3rdian

[phillay]

would 18x8 +15 and 18x9 +10 work on ep3? offset calc says theres more inner clearance but extending 43mm and 60mm from rear.

stock height

[Symphorced]

would 18x8 +15 and 18x9 +10 work on ep3? offset calc says theres more inner clearance but extending 43mm and 60mm from rear.

stock height

Could work but would look stupid.

[butterfingers]

would 17x9 +38 on a 215/45 profile tyre work on the rears of an ep3, how much camber would i need to clear the trailing arm?

[Symphorced]

would 17x9 +38 on a 215/45 profile tyre work on the rears of an ep3, how much camber would i need to clear the trailing arm?

don't you already have wheels in those specs? why not just test fit it and let everyone know how you go? lol

[butterfingers]

don't you already have wheels in those specs? why not just test fit it and let everyone know how you go? lol

yea thats true but the only DIY equipemtn i have is a funnel for topping up engine oil and a clay bar + bottle of wax.

i wanna have some peace of mind about this