EP3 Type R

[UNA91]

Are the wind deflectors/visors screwed on or just stuck on with adhesive tape? It looks like there's a few mounting screws on it but the visors i found online are only held by tape.

Mines looks like it's gonna crack and I want to get it replaced.

[doosra]

i might just do a major service on my car since I've only just purchased it so I know all fluids and parts are fresh..

-engine oil
-oil filter
-fuel filter
-brake fluid
-transmission fluid
-coolant

Am I missing anything? and how much do you think it this service will cost?

[butterfingers]

450-550 at Top One. i did the exact same service about 2 moinths ago.

[Symphorced]

i might just do a major service on my car since I've only just purchased it so I know all fluids and parts are fresh..

-engine oil
-oil filter
-fuel filter
-brake fluid
-transmission fluid
-coolant

Am I missing anything? and how much do you think it this service will cost?

Clutch fluid too.

Labour is what is going to cost the most in doing something like this. Should give it a shot yourself. Not too difficult and there are many guides around.

[doosra]

thanks.. i live near hanny's so will probably just take it to them..

i can do a simply oil change and oil filter, but don't know how to do the rest, plus would like to have receipts for future when i end up selling the car

[Lukezen27]

thanks.. i live near hanny's so will probably just take it to them..

i can do a simply oil change and oil filter, but don't know how to do the rest, plus would like to have receipts for future when i end up selling the car

hanny's

[uniqlo]

I've been looking around to buy a set.
From my research, only OEM ones have clips.
Other ones are sold with 3M tape that they swear will hold.
I'll likely be getting my OEM set from here.

Are the wind deflectors/visors screwed on or just stuck on with adhesive tape? It looks like there's a few mounting screws on it but the visors i found online are only held by tape.

Mines looks like it's gonna crack and I want to get it replaced.

[TonyxTony]

Yea I live like 2mins from sunnybank, it might be me... there are around 3-4 white ep3 around this area. Also saw one heading down south towards Parkinson from time to time

you can fit 17x8 in the back, but keep the offset between atleast +35 to +43, anymore and you might find you'll hit the guards or the rear trailing arm

btw i think i see your ep3 sometimes around sunnybank?

[TonyxTony]

That would be great bro, just in the market for some new wheels... bit hard to find 7.5" usually see 8" around

17x8 +43 on the rear is the Max you can do on 215's its pretty close the sussy. Might can try 225. If you want pics I can post for guide line.

[doosra]

I'm running 17 x 8 +35 offset but my guards are rolled. Here's how they sit.

Guard rolling is cheap. The guy that did it charged I think $35 per corner so much cheaper than tyre shops who charge about $60. Let me know if u want his details.

If you're not lowered, you probably dont have to roll them

[UNA91]

Yea I live like 2mins from sunnybank, it might be me... there are around 3-4 white ep3 around this area. Also saw one heading down south towards Parkinson from time to time

could be me? lol i head down that way to get home, but yea i've also seen a one that heads down that way too, no plate was epk20 or something

I've been looking around to buy a set.
From my research, only OEM ones have clips.
Other ones are sold with 3M tape that they swear will hold.
I'll likely be getting my OEM set from here.

so exxy!

[butterfingers]

That would be great bro, just in the market for some new wheels... bit hard to find 7.5" usually see 8" around

Going down to fit 17x9 at the back today. Ill let h know how that goes