Page 1 of 2 12 LastLast
Results 1 to 12 of 14
  1. #1

    Clicking noise, not CV joint

    I have a clicking noise when I turn (right I think). The car has new outer CV joints, and is fairly well looked after.

    The gearbox is a bit whiney, could it be the diff bearings? Or a wheel bearing?

    I've only just bought it so want to find out whats up with it.

    Thanks,
    Last edited by Marc_EE9; 26-03-2013 at 06:53 AM.

  2. #2
    Member Array
    Join Date
    Oct 2006
    Location
    Hunter Valley NSW
    Car:
    lownslowsedan
    wheel bearings shouldnt click.

    only when turning?

    noise change on speed?
    to see all of my build, checkout


  3. #3
    yeah its only when turning. Ive had a good poke about and there is no play in the shafts or bearings. the car needs new TRE's and a inner CV boot.... prehaps its an inner CV joint?

  4. #4
    Member Array
    Join Date
    Aug 2012
    Location
    canberra
    Car:
    DC2
    i just had a simmiler issue but i got a clunking (shook the whole engine and gearbox assy) every rotation of the wheel even ragardles of tuning or not. it was the inner cv where one slide would bind on the wall of the joint (poop rebuild prior) couldnt even tell untill i had degreased everything eather. i know you said its not the drive shafts but i thought id share the story as its not a common diagnosis for drive shaft failure...
    Last edited by Daveho1; 26-03-2013 at 04:30 AM.
    Mate my bbk cost more than your Honda.
    -Amant02

  5. #5
    Member Array
    Join Date
    Jun 2006
    Location
    Melb
    Car:
    DC
    Quote Originally Posted by Marc_EE9 View Post
    yeah its only when turning. Ive had a good poke about and there is no play in the shafts or bearings. the car needs new TRE's and a inner CV boot.... prehaps its an inner CV joint?
    TRE = tie rod ends?

    Pretty much answered your own question, if you already know whats wrong with it.

  6. #6
    I always thought TRE's knocked, not click...?

  7. #7
    Member Array
    Join Date
    Jun 2006
    Location
    Melb
    Car:
    DC
    How bad are yours?
    Loose as? or just a bit of play?

    Are you getting a single click? or continuous clicking as your turning?

  8. #8
    continuous, and the boots are shot and they have play, and knock going over potholes etc.

  9. #9
    Member Array
    Join Date
    Jun 2006
    Location
    Melb
    Car:
    DC
    Continuous sounds like your outter cv joints are gone.
    How old are the outter cv joints, if your car is lowered it'll kill the cv's quicker?

  10. #10
    i got same problem
    but just a bit of play
    sound like from rear left when turning
    what happen?
    type[R]

  11. #11
    the car isn't lowered, and the cv joints are brand new apparently.

  12. #12
    Member Array
    Join Date
    Oct 2006
    Location
    Hunter Valley NSW
    Car:
    lownslowsedan
    if the joints are brand new, they still could be stuffed.

    Especialy if they were a bit tight.
    to see all of my build, checkout


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.