Page 1 of 2 12 LastLast
Results 1 to 12 of 18

Thread: b16

  1. #1
    Newcomer Array
    Join Date
    Apr 2006
    Location
    syd
    Car:
    SEXC Rx8 NOW[RX87OY]

    b16

    hey guys, there is a problem with my b16a i did a conversion si to b16 about 2-3 weeks after i got it running iv had a problem with it. When im driving (when warm), It starts to like jolt just say ill be cruising at 60-70km my revs jump then go down then go up, and when i put my foot down it lags even more then jumps out of it. ok now iv changed : my fuel pump, f/filter, plugs, cleaned out the throttle body, cleaned my V-tec solanoid, new o/filter. Im thinking leads or something with the dizzy please help guys...!

    Thanks

    Adam

  2. #2
    what's the size of your throttle body?

  3. #3
    Newcomer Array
    Join Date
    Apr 2006
    Location
    syd
    Car:
    SEXC Rx8 NOW[RX87OY]

    b16

    its just the stock one im not shore how big but the stock one

  4. #4
    Member Array
    Join Date
    Apr 2006
    Location
    I'm here right now
    Car:
    JDM K20A
    It Looks Like One Of Your Sensor Needs To Be Replaced.
    Maf Sensor? O2 Sensor?

  5. #5
    Member Array
    Join Date
    Apr 2004
    Location
    Melbourne
    Car:
    Civic B16A
    check wiring..

  6. #6
    Array
    Join Date
    Aug 2003
    Location
    Unit 5/15 Sefton Rd, Thor
    Car:
    08 Red CU2 Euro
    Check the ignitor inside the dissy.
    TODA Performance Australia Pty Ltd
    TODA Racing - FIGHTEX - MFactory - HALTECH - EXEDY
    Race engines, Dyno tuning, Licenced workshop, Parts.
    P:0401869524 email: toda@todaracing.com.au

  7. #7
    Newcomer Array
    Join Date
    Mar 2007
    Location
    Adelaide
    Car:
    ED Sedan B16a2
    Quote Originally Posted by TODA AU View Post
    Check the ignitor inside the dissy.
    yup
    what he said

  8. #8
    Member Array
    Join Date
    Aug 2007
    Location
    Perth
    Car:
    EG Civic
    hey, yes i have had the same problems as you many times, first thing to do is test your leads one by one with a multimeter, To workout the proper reading it should be about 15 kiloohm per metre of ignition lead, if it does than your leads are good, if it reads about 15-18 kiloohm or more on any of your leads then you have a busted lead(s) the other thing i have noticed is that if there is even a small amout of water or even a small amount of oil that has leaked into the distributer cap through maybe a damaged seal it can do this exact same thing your explaining. do you ever have trouble starting the car?
    Last edited by B18cEG; 11-11-2007 at 11:08 AM.
    = First Production Company To Produce 100HP Per Litre NA

  9. #9
    Member Array
    Join Date
    Oct 2004
    Location
    Sydney - Cabramatta/Liver
    Car:
    Jazz EVO IX
    i'd change to new plugs also, and check your spark plug leads also
    Evo IX - THE FINAL EVOLUTION

  10. #10
    Member Array
    Join Date
    Aug 2007
    Location
    Wollongong
    Car:
    180sx
    Yea my car does this. But not so bad, it doesnt drop revs or gain revs, just chugs, like all jerky, then i put my foot down, and car makes a deep note, then starts pulling again.

    Was going to change plugs & leads, and see where that takes me.

    If you work yours out please tell me, i might have same problem.

  11. #11
    Member Array
    Join Date
    Apr 2006
    Location
    I'm here right now
    Car:
    JDM K20A
    Quote Originally Posted by 1996ek1 View Post
    Yea my car does this. But not so bad, it doesnt drop revs or gain revs, just chugs, like all jerky, then i put my foot down, and car makes a deep note, then starts pulling again.

    Was going to change plugs & leads, and see where that takes me.

    If you work yours out please tell me, i might have same problem.
    i got this problem last time, and it's because of my fuel filter was blocked.
    I found it after I've changed spark plugs and leads.

  12. #12
    Newcomer Array
    Join Date
    Apr 2006
    Location
    Brisbane
    Car:
    EG HATCH/ JDM DC2 :>
    bro i had the same problem on my f20b i changed the TPS man and everything went back to normal and check the pipes that connect into ur filters man maybe have a problem u cant get to

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.3


Terms and Conditions
Ozhonda.com is in no way affiliated with the Honda motor company or Honda Australia in anyway whatsoever.