EP3 Type R

[av90]

You can get an OEM one for less than that. Bet it will last better than that aftermarket one. Just saying.

how much is OEM? for oem the eu3 4door civic shares same as ep3 so i would get that. or dc5r too. im just reading around to see if omni is worth choosing over oem

cheers

[chargeR]

how much is OEM? for oem the eu3 4door civic shares same as ep3 so i would get that. or dc5r too. im just reading around to see if omni is worth choosing over oem

cheers

Click the link fellow! That link goes to an RSX clutch master cylinder from OEMacuraparts which should be about $140 shipped to Australia.

[av90]

lol didnt notice the hyperlink. thanks

[denrie]

Just a quick question guys. Do you know anywhere I can get the passenger air bag inflator from? I can't pass pink slip.

[RPS.13]

Can anyone recommend some alignment settings for hitting the track on the EP3?

Figures I was thinking of were:

Front:
-2 degrees camber
slight toe out (but I am unsure how many degree's)

Rear:
approx -1 to -1.5 degrees camber
0 toe

Height: will be about a 20mm gap between the tyre and guards

[chargeR]

Can anyone recommend some alignment settings for hitting the track on the EP3?

Figures I was thinking of were:

Front:
-2 degrees camber
slight toe out (but I am unsure how many degree's)

Rear:
approx -1 to -1.5 degrees camber
0 toe

Height: will be about a 20mm gap between the tyre and guards

Sounds like a good setup to start with, a little more negative camber at the front might not hurt. What tyres, spring rates and sway bars are you using? 2-3mm of toe out at the front should be a good amount to start with and should perceptibly improve turn in.

[RPS.13]

Sounds like a good setup to start with, a little more negative camber at the front might not hurt. What tyres, spring rates and sway bars are you using? 2-3mm of toe out at the front should be a good amount to start with and should perceptibly improve turn in.

Thanks for the feedback!

Tyres i'll be running are advan a048's, front:245/40/17, rear:225/45/17. Spring rates from memory are 8 front/10 rear. Unfortunately I haven't upgraded the swaybars yet, only changed the rear end links to nolathane items.

[Jibz]

Mike, will you be going to Winton on the 24th? I will be!

[RPS.13]

Hey Julian, nah unfortunately I won't be ready in time. I'm aiming to get down to Sandown in the middle of October.

Good to hear your hitting the track though. It should be awesome!

[keepitlow]

Can anyone tell me where to buy the Cabin Filter for EP3?

I happen to check my today and its pretty dirty.. thank you~

[av90]

its time to service the ep3... just wondering which coolants would you recommend i use ? and whats a good injector cleaner?

[stienerv2]

For injectors you can get them clean professionally for around 25 bucks each. If your looking for an additive try the Nulon Total fuel system cleaner.

For the coolant are you planning to professionally flush the whole thing out or not? If not which colour is it? Dont mix different colour coolants together. Normally for coolants there are 2 main colours. Green or red. For green there will be 2 types, type a or b. Type a will be better since it has anti boil, anti rust and anti freeze while type b will only have anti boil? Red coolant are generally better than the green coolants. However i've also heard that honda started to make a blue coolant which is currently one of the best in the market. If you dont wanna spend that much stick with Nulon green coolant, ive been using it and it's running fine. If your interested just pm me cause i think i have some left.