-
25-08-2011 09:35 AM
#3253
Originally Posted by DA9-47
Who's car that???^^^
i do wish i knew!
-
02-09-2011 11:01 AM
#3254
hey guys,
Please Help!!!
does anyone know what size the pressure plate mounting bolts for the tranny are?
im stuck............. i got nothing that fits............ its like bigger than a 10mm, and smaller than a 11mm, 7/16 fits best but still spins a little,
i got newer engine in and i separated the tranny from old engine , just cant get the fukn pressure plate ,clutch and fly off cause of those 9 bolts holding the pressure plate down
dont wanna buy a whole set of new sockets, would prefer to buy just the one if someone can tell me for sure what it is ?????
Please help
-
02-09-2011 11:07 AM
#3255
Originally Posted by mooshie
You can just get the engine mounted up and then sort out the gearbox later from underneath. bit harder than just wacking the whole thing in there at once though. cant you just keep the hoist hired for another couple of days?
i went down the "add tranny later" road
been strapped for cash so couldn't afford to get hoist for another day, and lucky cause i still wouldn't have had it out lol,
i think ill b right as long as i can get the pressure plate off , just more time consuming doing it this way, but safer in the long run for a first timer i reckn
-
02-09-2011 11:31 AM
#3256
Originally Posted by DA9-47
hey guys,
Please Help!!!
does anyone know what size the pressure plate mounting bolts for the tranny are?
im stuck............. i got nothing that fits............ its like bigger than a 10mm, and smaller than a 11mm, 7/16 fits best but still spins a little,
i got newer engine in and i separated the tranny from old engine , just cant get the fukn pressure plate ,clutch and fly off cause of those 9 bolts holding the pressure plate down
dont wanna buy a whole set of new sockets, would prefer to buy just the one if someone can tell me for sure what it is ?????
Please help
there 10mm with a double hex
-
02-09-2011 11:43 AM
#3257
Originally Posted by stevo716
there 10mm with a double hex
life saver ...as usual lol,
going to try buy it now
thanks man
-
03-09-2011 11:54 AM
#3258
can anyone help me. my car normally turns on and revs to about 1500 rpm,then drops down very low to about 300, and then levels out at around 1000. Now I have noticed the car turns over a lot more before it starts, and sometimes when it starts it revs up to 1500 and then goes all the way down and stalls? something to do with ignition switch or relays?
any ideas would be great cheers
-
03-09-2011 03:42 PM
#3259
try the basic things first like checking for spark and pull the plugs and make sure they all look fine. take the cap off the distributor and see if the points and rotor look ok and that the connections on the igniter are tight. make sure your leads are in good nick and tightly fitting
when was the last time you changed your fuel filter? this can also impact but usually causes more problems at high revs/load than low.
try these and see if it works.
DA9 LS w/JDM SiR B18C turbo
Looking for older Honda project car pre-1985
-
03-09-2011 08:19 PM
#3260
wat mooshies said... but if all is good it could be an issue with your cold start stuff. check vac lines etc. but after wat mooshie said. lol
-
05-09-2011 03:46 PM
#3261
i fixed it, but another problem was revealed.............petrol light is broken..........facepalm
thanks anyway
-
05-09-2011 08:31 PM
#3262
Originally Posted by ben11
i fixed it, but another problem was revealed.............petrol light is broken..........facepalm
thanks anyway
thought da9s didnt have petrol light?
-
05-09-2011 08:35 PM
#3263
Originally Posted by stevo716
thought da9s didnt have petrol light?
really? i just assumed all cars did and ran my car dry trying to find out if it worked or not lol
-
05-09-2011 09:02 PM
#3264
Originally Posted by ben11
really? i just assumed all cars did and ran my car dry trying to find out if it worked or not lol
nah my old da9 didnt
i got a da6 now that does tho
its a pointless thing anyway lol, needle does same job :P
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
Bookmarks