EP3 Type R

[Nepolian]

1)Cut you original header at the front of the cat and weld in new cat:

Why needed to be cut?? and cant you just buy a cat and bolt it on??

2)take the header off the engine and grind off the welds inside the flange:

what's good about that?


Sorry i just have no idea on these stuff


thanx N.M

No worries!

The cat and the secondary header is one piece so it needs to be cut.

The welds restricts airflow from the head. There is quite a large weld which sits inside. Reducing/eliminating this would increase flow

[SuperSteve]

No worries!

The cat and the secondary header is one piece so it needs to be cut.

The welds restricts airflow from the head. There is quite a large weld which sits inside. Reducing/eliminating this would increase flow

Hurry up and organise a meet up so we can discuss these things over a coffee mate !

[EP3EVA]

No worries!

The cat and the secondary header is one piece so it needs to be cut.

The welds restricts airflow from the head. There is quite a large weld which sits inside. Reducing/eliminating this would increase flow

would be better off doing a custom headers instead??

Or the OEM header is good enuff?

[Nepolian]

would be better off doing a custom headers instead??

Or the OEM header is good enuff?

Depends on your budget and what mods your after. OEM header is not bad, but can be improved. In no way am I comparing it to a Toda header etc....but then again modding the OEM header wont cost a few weeks wage either!

The OEM header is a properly made stainless steel header with mandrel bends, so i'd say it aint too bad!

Steve, I'll put something up as soon as I get my roster tomorrow. Cant organise something when I dont know when I am available

Soon mate, soon......

[EP3EVA]

hmm do like aftermarket header's have build in cat's?? just like the OEM's??

[Nepolian]

hmm do like aftermarket header's have build in cat's?? just like the OEM's??

In short....NO!

Heres an idea of cost! Its a rough guestimate but I'd be quite close!

Mugen header with cat $2500ish
Toda race header (no cat) $1500ish
Buddy club race header (no cat) $1300ish
Maximworks header with cat $2500ish
SSR raceheader (no cat) $2500

Basically you'd be spending $1500 upwards to have a set of headers modified with a cat!

Working with my $100 per KW principal......fail unfortunately, money better spent elsewhere!

But this is my personal opinion

[n5920787]

there you go...


http://shop.ebay.co.uk/items/__r-lea...fSMQQ_fromfsbZ

Sweet!!! Thanks

[veecee]

Got mine here - http://www.redlinegoods.com/general.shtm. Nice quality leather. Just need to pull my finger out and fit it!

[ep3_ctr]

thinking of selling my ep3. What do you think i should advertise for?

2002 Model - 25000 kms

Mugen Double Loop Exhaust
Mugen Airbox
Carbon Front Sway Bar
Rear Sway Bar
Endless Brake Pads
Razo Gear Knob
JVC Deck
Top of the range Pioneer Speakers throughout
Carbon Tweeter Mounts
Recent Service
Rays Gram Lights - 57 Maximum - 17 inch unmarked perfect condition
HKS FCON IS

[Nepolian]

^ hey george...yeah...been a while...

let me know when this happens...but not free next sat...

Hey Sydney guys,

Is the first couple of weeks in march a good time for you?

What do you prefer, weekdays or weekends?

Let me know!

[icecrm]

i dont mind

any will do

[sai_ANN]

Hey Sydney guys,

Is the first couple of weeks in march a good time for you?

What do you prefer, weekdays or weekends?

Let me know!

march is good for me...weekdays or weekends...but pref weekends...