EP3 Type R

[Mugen_B16B]

Most C clamps should work, I can drop some off to Philip/Justin for you to borrow if you like?

****MUGEN B16B**** Pics below!
sweet! that on skunk 2's? u said ur spoons were lower or same as skunks?

[Nepolian]

sweet! that on skunk 2's? u said ur spoons were lower or same as skunks?

Not as low. Just a little lower than stock. But it rode really well where as the S2's was quite hard! In short, Spoon felt really balanced with stock sussy!

[Perry]

Most C clamps should work, I can drop some off to Philip/Justin for you to borrow if you like?

****MUGEN B16B**** Pics below!


I just wet my pants :thumbsup:

[Rai-C]

ps anyone here friends with monqiue chuong my friend told me someone just got an ep3 and just wondering if he is here. =D

she's friends with alot of my friends.. met her at a party one time and she mentioned that she tried to race me once in her mini when i was driving my legend haha

[Rai-C]

Alot of the stuff you'd get is quite heavy.......and expensive to post or even carry and be over the weight limit! (referring to sussy, exhaust etc...)

You're really limited to the smaller stuff which is easy to carry....like maybe....intakes, cams and the likes!

yes.. parents are being very generous these days. im very suspicious lol.
any particular brands i should be looking at in the states? already lookn at some blox, skunk2 and injen stuff

[denrie]

Anyone here from Western Sydney that I can borrow your rims or know anyone that I can borrow rims to pass pink slip tomorrow? Or know any places that isn't to strict?

[k0e1]

she's friends with alot of my friends.. met her at a party one time and she mentioned that she tried to race me once in her mini when i was driving my legend haha

Haha. That girl is a speed demon. Haha. Dw I'm sure an ep3 will keep her quiet. I'll tell her you said hi. Good luck with the mods.

[Mugen_B16B]

Haha. That girl is a speed demon. Haha. Dw I'm sure an ep3 will keep her quiet. I'll tell her you said hi. Good luck with the mods.
dw i raced a few mini's and u will beat them, one had exhaust and reflash and i just beat by half car

[Rai-C]

Anyone here from Western Sydney that I can borrow your rims or know anyone that I can borrow rims to pass pink slip tomorrow? Or know any places that isn't to strict?

hahah its the west.. i think you'll find somewhere shifty :P

[Rai-C]

Haha. That girl is a speed demon. Haha. Dw I'm sure an ep3 will keep her quiet. I'll tell her you said hi. Good luck with the mods.

yes speed demon indeed lol too bad i was in my legend though! she was weaving through traffic and there i was in a boat of a car lol! yeah tell her to find me on facebook or something haha

[SuperSteve]

saw a ep3 near fairfield BP on Horsley Drive. I was driving along the rail line at villawood coming up to the Horsley Drive T intersection. Anyone from here ?? Was a pre facelift

[NightRyder]

there must be heaps of EP's down your way now hey Steve?.....gosh...the EP community is growing fast!. :D

[Nepolian]

LOL! could be any one of 10 billion...........

[SuperSteve]

there must be heaps of EP's down your way now hey Steve?.....gosh...the EP community is growing fast!. :D

hahaha yeah mate thats because EP3 are now the SEX ! !



shhhhhh dont tell type S Tony ! !

[Perry]

LOL is he the dude on club itr spamming away most of the days?

[NightRyder]

hehe...

the only other EP owner down that way that I could think of is ekhybrid (the other Steven)...perhaps it's him?..

regardless, I reckon if me, George, Perry and Jimmy go down to HJ's on the cumberland highway intersection, and you joined us, the other EP's might be drawn to us and we'd be famous...hahahaha... :P


hahaha yeah mate thats because EP3 are now the SEX ! !



shhhhhh dont tell type S Tony ! !

[NightRyder]

It is Perry, he's the man at doing that.


LOL is he the dude on club itr spamming away most of the days?

[Perry]

hehe...

the only other EP owner down that way that I could think of is ekhybrid (the other Steven)...perhaps it's him?..

regardless, I reckon if me, George, Perry and Jimmy go down to HJ's on the cumberland highway intersection, and you joined us, the other EP's might be drawn to us and we'd be famous...hahahaha... :P

lets do it KK livo anyone tonite? LOL

[NightRyder]

tonight?...sorry dude, can't do tonight. Got to be at court early tomorrow.


lets do it KK livo anyone tonite? LOL

[Perry]

tonight?...sorry dude, can't do tonight. Got to be at court early tomorrow.

all good another time a few EP3 just rock around the area and Steve will be like I Spotted more EP3's in the area!!! hehehe

[denrie]

So many EP3's now! Saw one today at Cumberland Highway. Number plates were YIZ.23R. Anyone from here? It was a Pre Facelip and looks like it's just been cleaned.

[SuperSteve]

hahaha dam so many ep3's :D

dam wish i saw ur msg earliar perry i would have went there :D for a coffee since i owe u guys 1 each anyways hahaha

[Perry]

WE just orgainse one next week yeah. KK coffee hehehe

[ekhybrid]

hehe...

the only other EP owner down that way that I could think of is ekhybrid (the other Steven)...perhaps it's him?..

regardless, I reckon if me, George, Perry and Jimmy go down to HJ's on the cumberland highway intersection, and you joined us, the other EP's might be drawn to us and we'd be famous...hahahaha... :P

paul what u been upto maaaaate
going back to japan soon!

[Rai-C]

saw a ep3 near fairfield BP on Horsley Drive. I was driving along the rail line at villawood coming up to the Horsley Drive T intersection. Anyone from here ?? Was a pre facelift

steve it was probably the one you saw last time, and thought it was me haha


regardless, I reckon if me, George, Perry and Jimmy go down to HJ's on the cumberland highway intersection, and you joined us, the other EP's might be drawn to us and we'd be famous...hahahaha... :P

im there nearly every day :( LOL


lets do it KK livo anyone tonite? LOL

and i was there tonight hahaha

my point is, I WISH I SPOTTED MORE OF YOU GUYS AROUND LOL

[Mugen_B16B]

dam u guys should get personalised plates

[icecrm]

Yizzer is my mate. i think he has an account on ozhonda but doesnt post much if at all

alot of us do have personalised plates, me, nepolian, sai_anne, thats all i can think of hahahaha

[denrie]

Yizzer is my mate. i think he has an account on ozhonda but doesnt post much if at all

alot of us do have personalised plates, me, nepolian, sai_anne, thats all i can think of hahahaha

ahh kk. i think i seen him like 2 weeks ago at parra. lol

[denrie]

You reckon our cars would look good with the euro plates?

[NightRyder]

steven...been quiet there hey?....i'm alright, just chilling. :P

Japan?...I wish man, I wish....but dollar aint as good as it was when I was there almost a year ago. I'd definitely do it again down the track when the dollar is good. :)


paul what u been upto maaaaate
going back to japan soon!

[SuperSteve]

You reckon our cars would look good with the euro plates?

naaaa

red plates = hot :D

[NightRyder]

personally I didn't think it suit my taste, but indeed the front bumper indent does accommodate the euro plates if you were to get some.
And I think you are slightly limited to what you can put on the euro plates since you must have the "N" at the beginning no matter what.

As Steve said, I think the red plates look nice...


You reckon our cars would look good with the euro plates?

[denrie]

personally I didn't think it suit my taste, but indeed the front bumper indent does accommodate the euro plates if you were to get some.
And I think you are slightly limited to what you can put on the euro plates since you must have the "N" at the beginning no matter what.

As Steve said, I think the red plates look nice...

It's changed now. The euro plates can be personalised like any other plates. Just wandering what other people thought about it thats all :) Getting new plates soon but don't know what to put. AHAHA

[NightRyder]

oh it has?...cool, about time too!...LOL

gosh...this State has grown in car numbers so much, what are they (RTA) going to think of next to bring to the plate variety it already has...hehe...

wonder where I put my list of number plate word combinations..........


It's changed now. The euro plates can be personalised like any other plates. Just wandering what other people thought about it thats all :) Getting new plates soon but don't know what to put. AHAHA

[Rai-C]

i want george's plates! dammit.

[Moey.C]

i want george's plates! dammit.

good racing the other night

for a stocker

impressed me!!!

:thumbsup: :wave:

[Perry]

Any of you guys were at Livo KK tonight?

[Mugen_B16B]

personally I didn't think it suit my taste, but indeed the front bumper indent does accommodate the euro plates if you were to get some.
And I think you are slightly limited to what you can put on the euro plates since you must have the "N" at the beginning no matter what.

As Steve said, I think the red plates look nice...

hahah lucky for me qld euro plates start with Q and my name starts with it, so i could use my nikname quati

[Rai-C]

Any of you guys were at Livo KK tonight?

i was :)


good racing the other night

for a stocker

impressed me!!!

:thumbsup: :wave:

thanks dude :) i impressed myself too! im still getting to know my car, and im still developing my own driving style etc.. ive only been driving manual for a month now >< lol burnouts are fun :)

[denrie]

hahah lucky for me qld euro plates start with Q and my name starts with it, so i could use my nikname quati

You got euro plates on your EP3? If so, pics? :)

[Mugen_B16B]

nah im just saying lucky my name starts with a Q if i were to get plates, still thinking on some down the track but not atm

[Moey.C]

thanks dude :) i impressed myself too! im still getting to know my car, and im still developing my own driving style etc.. ive only been driving manual for a month now >< lol burnouts are fun :)

haha dont worry man not sure what ep3rs run stock but i dont think its much better than mid 14s stock n dats wat u accomplished. and to hav only been drivin a month lol pretty good man
:thumbsup:

[Nepolian]

haha dont worry man not sure what ep3rs run stock but i dont think its much better than mid 14s stock n dats wat u accomplished. and to hav only been drivin a month lol pretty good man
:thumbsup:

Chubbysteve and I have done 13.9 with SRI and catback. I'm pretty sure Chubbysteve did 14.1.....full stocker too....I'll let him confirm that tho!

[Mugen_B16B]

13.9 sounds awesome, on that civic type r ep3 UK youtube clip they were only doin low 14's which imo is so crap, and they got supercharge aswell???? wats the go? and some were jdm ep3's aswell

[Perry]

[QUOTE=Rai-C;2436091]i was :)

Cool I'll come over and say high to you next time.

[white_ep3_civic]

Does any1 no how 2 pull out the standard grille? I've got the 4 top plastic screws out just can't work out way is holdin it still

[Rai-C]

Cool I'll come over and say high to you next time.

yes please do it! haha

[Rai-C]

Does any1 no how 2 pull out the standard grille? I've got the 4 top plastic screws out just can't work out way is holdin it still

Remove the front bumper
Remove the front grille
Remove the screws
Remove the clips
Release the bottom hooks of the grille.
Pull out the bottom of the grille to release the upper hooks
Pull out the grille to release the slits from the ribs, then remove the grille.

copy-pasted from the ep3 service manual :) who wants one? lol

[Perry]

yes please do it! haha

Wasnt sure if you were one of ozhonda members so yeah.

[white_ep3_civic]

Remove the front bumper
Remove the front grille
Remove the screws
Remove the clips
Release the bottom hooks of the grille.
Pull out the bottom of the grille to release the upper hooks
Pull out the grille to release the slits from the ribs, then remove the grille.

copy-pasted from the ep3 service manual :) who wants one? lol

Aww man that is so much shit 2 do just to get the grille out!

[Rai-C]

Wasnt sure if you were one of ozhonda members so yeah.

haha maybe i should get an OH sticker? yeah i have the same worry when i wanna approach someone else i THINK may be on OH but aren't.. you end up looking like the biggest d-head lol


Aww man that is so much shit 2 do just to get the grille out!

yeah i had a feeling it was clipped to the front bar! why do you need to remove the grille? replacing it for a mugen?

[Rai-C]

hey guys click here (http://rapidshare.com/files/272623611/Civic01-05.zip.html) to download the service manual for our cars.. its only available for 10 downloads.. so please share :) [ZIP FILE - 164MB]

[white_ep3_civic]

yeah i had a feeling it was clipped to the front bar! why do you need to remove the grille? replacing it for a mugen?

Yeh I bought a mugen grille. Hopefully it will look the part cause it a copy 1.

[Perry]

Yeh I bought a mugen grille. Hopefully it will look the part cause it a copy 1.

How much was it if u dont mind me asking?

[SuperSteve]

How much was it if u dont mind me asking?

hahaha get 1 ! !

[Mugen_B16B]

0-60W any good for ep3? if not just gonna get 0-40w

[Nepolian]

How much was it if u dont mind me asking?

One million dollars!


hahaha get 1 ! !

Get one, its only a million dollars!


0-60W any good for ep3? if not just gonna get 0-40w

LOL! 0-60! Are you serious? 0-40 or any combo in between is just fine :)

[white_ep3_civic]

How much was it if u dont mind me asking?

I paid $150.00AU for it off ebay. But then had 2 buy a mugen badge and also still need to get a H badge. So all up about 180.00. Plus you need to get it painted.

[stoj19]

In my opinion just stick with the standard plates and spend the money on mods instead of handing it to the RTA. We all ready give them enough money. :p

[ITRDC2]

I paid $150.00AU for it off ebay. But then had 2 buy a mugen badge and also still need to get a H badge. So all up about 180.00. Plus you need to get it painted.

so 30 for the mugen and h badge?i doubt it will be the genuine ones......

[Rai-C]

im really considering buying some FL projector headlights when im in the states.. they fit with the PFL front bar and bonnet don't they?

[k0e1]

hey guys bit of a problem. i cant raise my car back up i have tein superflex. below is a picture of my back suspensionhttp://pic70.picturetrail.com/VOL1877/8801430/16270980/372971595.jpg
My mechanic tried to raise my car but apparently it doesnt work cause there are only two rings on it. can anyone help me out here?

[Nepolian]

hey guys bit of a problem. i cant raise my car back up i have tein superflex. below is a picture of my back suspensionhttp://pic70.picturetrail.com/VOL1877/8801430/16270980/372971595.jpg
My mechanic tried to raise my car but apparently it doesnt work cause there are only two rings on it. can anyone help me out here?

?? How many rings are there suppose to be ?? Because its down all the way just turn the top one first!

Cleaning the threaded body and apply a little lube will also help. At least with a little soapy water to get it going!

[k0e1]

?? How many rings are there suppose to be ?? Because its down all the way just turn the top one first!

Cleaning the threaded body and apply a little lube will also help. At least with a little soapy water to get it going!

The front one has 3 rings. no idea he tried it for like 2 hours so yeah maybe i'll give it a try ==' going to die hahha..

[white_ep3_civic]

so 30 for the mugen and h badge?i doubt it will be the genuine ones......

Yeh bout that. Nope the whole thing isn't genuine. Depends which 1 u get. They range from 20 - 60 4 the h badge.

[Nepolian]

so 30 for the mugen and h badge?i doubt it will be the genuine ones......

Really?


The front one has 3 rings. no idea he tried it for like 2 hours so yeah maybe i'll give it a try ==' going to die hahha..

The front is base adjustable hence the thrid ring at the bottom. Shouldn't really touch that!

The rings are meant to be tight for obvious reason :thumbsup:

[k0e1]

Really?



The front is base adjustable hence the thrid ring at the bottom. Shouldn't really touch that!

The rings are meant to be tight for obvious reason :thumbsup:

Ok so I'll try to rotate the top ring. Cause for the front he rotate the second and third so basically he adjusted the height by twisting the second ring so that is wrong?

[Nepolian]

Ok so I'll try to rotate the top ring. Cause for the front he rotate the second and third so basically he adjusted the height by twisting the second ring so that is wrong?

By the sounds of it, the front has been raised by the base. Its fine but it'll still be softish due to the springs being expanded.

This is assuming that you're counting the rings from the top? Top down 1-2-3.

[k0e1]

im so confused cause this other person has 3 thread in his one and the people were saying to unlock the bottom one and twist the whole coilover down?

this is mine with 2 threads?
http://pic70.picturetrail.com:80/VOL1877/8801430/16270980/372971595.jpg

3 threads here
http://pic70.picturetrail.com/VOL1877/8801430/16270980/373004944.jpg

Thanks

[Nepolian]

im so confused cause this other person has 3 thread in his one and the people were saying to unlock the bottom one and twist the whole coilover down?

Thanks

OK, I always count the two rings holding the spring 1 and 2. The third one at the bottom is for the base, not the spring. Up spec coil overs are not just spring height adjustable but also shock body adjustable to a greater range of adjustment. Without going too deep into it, its to do with setting height of the car without disturbing the spring tension/rate.

With yours, (being flex) its just the fronts which has this. What I'm saying is, your car have been lowered (heaps). And the springs should be tensioned relative to the height of the car. If it has been done, I would dwell on it too much, so long as its at your desired height.

As for the rear, like most medium level coilovers, are only height adjustable via spring. There fore there is only two rings. One to adjust the height and one to secure it (locking ring). Normally the bottom one acts a locking ring.

But since yours is down all at way, you can only go up. Twist the top one up and then follow it with the bottom one. To get 1 finger gap on the rear, adjust it so there is about 10-15mm of thread under the bottom ring.

See pic below. When adjusted, both lower and raises the height of shock....therefore car!

But Pic 1, adjusts the car via the spring height, therefore changing the spring tension and rebound ability etc.....Pic 2 adjusts the height of the car without changing spring characteristics.

[k0e1]

alright mad so simply just twist the 1st thread on my back to unlock it and then adjust it by rotating the second thread to raise it up and down?

[Nepolian]

alright mad so simply just twist the 1st thread on my back to unlock it and then adjust it by rotating the second thread to raise it up and down?

Rotate the top ring to get desired height and lock it with bottom ring!

[k0e1]

Rotate the top ring to get desired height and lock it with bottom ring!

must be frustrating for you so basically unlock the bottom ring first and twist the top ring to adjust height then lock back with bottom ring hahhaa

[Nepolian]

must be frustrating for you so basically unlock the bottom ring first and twist the top ring to adjust height then lock back with bottom ring hahhaa

Its all cool!

[SuperSteve]

ur da man george ! !

[k0e1]

Its all cool!

ok ran into a bit of trouble. man im a newb.
http://pic70.picturetrail.com/VOL1877/8801430/16270980/373013831.jpg
so i got 2 c spanners one on 1. and another one on 2. so i tried twisting the bottom one(2.) anti clockwise and the top(1.) clockwise to try to unlock it but its like not even budging with wd40.

After a few attempts now when i try to turn it both 1. and 2. are moving at the same time. is this meant to happen or is it still locked?

[Mugen_B16B]

be easier if u took the whole shock off and did it

[k0e1]

be easier if u took the whole shock off and did it

way too big of a job hahha

[KaZe86]

way too big of a job hahha

done it yesterday i got buddy club racing spec dampers in the rears took way quicker then the fronts i mean way quicker like honestly 5-10 mins to take off

but yeah i was a bit lost yesterday with the rings and stuff my mind wasent there but yeah if the rings are turning then thats good

turn the ring to move the spring up to raise the car or u can turn the bottom purch down to make it higher also im pretty sure but yeah will post some pics soon

[Nepolian]

ok ran into a bit of trouble. man im a newb.
so i got 2 c spanners one on 1. and another one on 2. so i tried twisting the bottom one(2.) anti clockwise and the top(1.) clockwise to try to unlock it but its like not even budging with wd40.

After a few attempts now when i try to turn it both 1. and 2. are moving at the same time. is this meant to happen or is it still locked?

Get spanner and turn to right (see pic). This may take a little effort. Because your is down all the way, don't worry too much about unlocking the bottom one at this stage. Just use c spanner to hold in place!

Don't take it out, easier to adjust on the car!

[SuperSteve]

done it yesterday i got buddy club racing spec dampers in the rears took way quicker then the fronts i mean way quicker like honestly 5-10 mins to take off

but yeah i was a bit lost yesterday with the rings and stuff my mind wasent there but yeah if the rings are turning then thats good

turn the ring to move the spring up to raise the car or u can turn the bottom purch down to make it higher also im pretty sure but yeah will post some pics soon

ur rsd noisy ?? I hear noises when i go over bumps

[denrie]

ur rsd noisy ?? I hear noises when i go over bumps

Is it because of the pillar mounts?

Does anyone want to share the EP3R Service manual?

[KaZe86]

ur rsd noisy ?? I hear noises when i go over bumps

nope mines fine man did u get yours new or used? mines fine the only noise i hear is it hitting the guards here and there lmao!

[k0e1]

Get spanner and turn to right (see pic). This may take a little effort. Because your is down all the way, don't worry too much about unlocking the bottom one at this stage. Just use c spanner to hold in place!

Don't take it out, easier to adjust on the car!

ok quick update so i manage to loosen it and man that thing was stiff. just a quick question if i want to raise it like 2cm do i just leave a gap of 2 cm(between that red line in the picture)? and when im done i just clockwise the bottom ring to lock it right?
http://pic70.picturetrail.com/VOL1877/8801430/16270980/373025202.jpg

[Nepolian]

ok quick update so i manage to loosen it and man that thing was stiff. just a quick question if i want to raise it like 2cm do i just leave a gap of 2 cm(between that red line in the picture)? and when im done i just clockwise the bottom ring to lock it right?

Good O........yeah try 2cm first, its really trial and error!

[k0e1]

Good O........yeah try 2cm first, its really trial and error!

ok done one side... so tired. cant do the other side its too stiff so maybe tommorow is it alrite if i just leave my jack there supporting one side for the night?

mechanics must be tanks if they find turning these joints with breeze.

[KaZe86]

ok done one side... so tired. cant do the other side its too stiff so maybe tommorow is it alrite if i just leave my jack there supporting one side for the night?

mechanics must be tanks if they find turning these joints with breeze.

is your car in a garage or what? hope so but yeah if u have a jack stand i reckon you should use that instead of just a jack not that safe imo

[k0e1]

is your car in a garage or what? hope so but yeah if u have a jack stand i reckon you should use that instead of just a jack not that safe imo

yeha its in the garage. didnt have a stand so i just finsihed the other one. all done. now i just have to do proper measurement.
BTW thanks to nepolian will give u back the c spanners once i properly finish. thanks and owe you another one

[Rai-C]

DUE to inundation of PM inbox, i have reuploaded the EP3 Service Manual HERE (http://www.zshare.net/download/64880402a6699af4/) :) and im pretty sure there's unlimited downloads :) so i hope nobody misses out this time!

BUMP: Earlier question.. do facelift headlights fit on the pre-facelift without need for a new bar etc?

[Mugen_B16B]

direct fit but need to redo wiring to work

[Perry]

Like mugen B16B said you will need to redo wiring for the high beam to work.

[Rai-C]

what kind of wiring? and what is the difficulty level on 1 to 10.. 1 being easy and 10 being 'oh my god eff this im buying a toyota'

[Perry]

Nightrider or George will be the right person to explain. It's something to do with an extra wire to make the high beam to work.

[SuperSteve]

yup ask Nightryder or Nepolian for some help mayb they might b able to help u

[Mugen_B16B]

just ask them to make a wiring diagram of the colors of which ever cable u will need to cut and redo

[burak213]

images removed

[SuperSteve]

burak213

plates mate cover the plates ! !

[burak213]

its from google man!!

you want me to delete it? is it yours?

[Perry]

I know the owner of the EP3 please delete it?

[KaZe86]

whats wrong with the plates? :confused:

anyways heres my ep3 with buddyclub racing spec dampers fronts need to go lower imo but yeah just a few phone pics for now thanks to the fys boys for the help on sourcing and installing as we do :thumbsup:

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image221.jpg

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image222.jpg

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image223-1.jpg

[Mugen_B16B]

if u wanna go lower u need t1r tie ends at front steven

[KaZe86]

if u wanna go lower u need t1r tie ends at front steven

oh yeah? is that the reverse tie rod end thing?

[SuperSteve]

oh yeah? is that the reverse tie rod end thing?

inverted tie rod ends :thumbsup:

HOWEVA i have been told that the rsd for ep3 was designed so u dont need inverted tie rods (correct me if im wrong someone), UNLESS ofcourse u lower ur car excessively

[KaZe86]

inverted tie rod ends :thumbsup:

HOWEVA i have been told that the rsd for ep3 was designed so u dont need inverted tie rods (correct me if im wrong someone), UNLESS ofcourse u lower ur car excessively

well have u got them steve? also would you be able to take a picture of your tie rod for me? thanks mate

[Perry]

inverted tie rod ends :thumbsup:

HOWEVA i have been told that the rsd for ep3 was designed so u dont need inverted tie rods (correct me if im wrong someone), UNLESS ofcourse u lower ur car excessively

Steve remember my EP3 when it was dumped it doesnt have any of the inverted tie rods for the front.

[SuperSteve]

well have u got them steve? also would you be able to take a picture of your tie rod for me? thanks mate

sorry steve i dont got any inverted tie rods installed at the moment :(

[KaZe86]

sorry steve i dont got any inverted tie rods installed at the moment :(

nah just the stock is ok i wanna see somthing thats all if thats ok

[EGBOY]

whats wrong with the plates? :confused:

anyways heres my ep3 with buddyclub racing spec dampers fronts need to go lower imo but yeah just a few phone pics for now thanks to the fys boys for the help on sourcing and installing as we do :thumbsup:

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image221.jpg

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image222.jpg

http://i77.photobucket.com/albums/j44/KaZe1_2006/Image223-1.jpg
looking good steve :P

[KaZe86]

thanks ian lols looking foward to seeing ur car man ;D

[Mugen_B16B]

t1r sells the inverted tie rods steven, im not 100&#37; sure but u might need dc5 rods aswell could someone confirm? i think its to stop the stress on the steering rack when u lower the car more at the front

[denrie]

Nah you just need the Inverted Tie Rods. No need for the DC5's.

[namr]

Hey guys

New to the forums, thought I should say Hi and introduce myself.
I'm from melbourne, thomastown and i've had my 02 cw ep3 for about 4-5 months now and I bought it stock private sale with 42,000kms on the clock

current mods

BC sports coilovers
Gruppe M intake
J's racing FX 60RS
spoon radiator
5zigen alloy wheels 17" (came with the car they look Ok...)
bridgestone potenze RE11's.

i've got a pic on my iphone but not sure how to upload on a site so everyone can see. ill sus it out over time :)

this car is my pride and joy, hope to share some of my good and bad experiences with it.

nice to meet you all.
Nam

[Nepolian]

Welcome Nam :)

Sydney peeps.....heads up, this coming weekend lunch meet coming! Make yourselves available. Prob Saturday!

Should see coming post from NightRyder or myself :)

[denrie]

Welcome Nam :)

Sydney peeps.....heads up, this coming weekend lunch meet coming! Make yourselves available. Prob Saturday!

Should see coming post from NightRyder or myself :)

What time? Make it morning! Also thanks heaps for today George & sorry for making you drive all the way to my house and all :)

[Nepolian]

What time? Make it morning! Also thanks heaps for today George & sorry for making you drive all the way to my house and all :)

It'll be a late morning coffee, followed by a possible Korean BBQ lunch! Everyone welcomed to either one or both.....wait for details :)

No worries Den! enjoyed the drive!

[ITRDC2]

Hey guys

New to the forums, thought I should say Hi and introduce myself.
I'm from melbourne, thomastown and i've had my 02 cw ep3 for about 4-5 months now and I bought it stock private sale with 42,000kms on the clock

current mods

BC sports coilovers
Gruppe M intake
J's racing FX 60RS
spoon radiator
5zigen alloy wheels 17" (came with the car they look Ok...)
bridgestone potenze RE11's.

i've got a pic on my iphone but not sure how to upload on a site so everyone can see. ill sus it out over time :)

this car is my pride and joy, hope to share some of my good and bad experiences with it.

nice to meet you all.
Nam

hey mate, can u upload some exhaust clip from ur car onto youtube?i want the j's 60rs as well! cheers!

[namr]

hey mate, can u upload some exhaust clip from ur car onto youtube?i want the j's 60rs as well! cheers!

Hey mate,

I'll see if i can over the weekend, need to find a video camera aswell.
expensive but you wont regret it! :)

[SuperSteve]

it'll be a late morning coffee, followed by a possible korean bbq lunch! Everyone welcomed to either one or both.....wait for details :)

no worries den! Enjoyed the drive!

yeah bring on da korean bbq ! ! !

[ITRDC2]

lol never regret on j's , but i just dont want to get pulled over if j's too loud lol, thats why i need to double check the 60rs :)

[Perry]

Hey guys

New to the forums, thought I should say Hi and introduce myself.
I'm from melbourne, thomastown and i've had my 02 cw ep3 for about 4-5 months now and I bought it stock private sale with 42,000kms on the clock

current mods

BC sports coilovers
Gruppe M intake
J's racing FX 60RS
spoon radiator
5zigen alloy wheels 17" (came with the car they look Ok...)
bridgestone potenze RE11's.

i've got a pic on my iphone but not sure how to upload on a site so everyone can see. ill sus it out over time :)

this car is my pride and joy, hope to share some of my good and bad experiences with it.

nice to meet you all.
Nam


Welcome dude and hoping to see some pics soon.

[namr]

lol never regret on j's , but i just dont want to get pulled over if j's too loud lol, thats why i need to double check the 60rs :)

thats the way.. j's is the way to go!

the 60RS imo is perfect, doesnt idle too loud, when u fang it it comes alive but normal everyday driving wont even notice it. when i first put it on, i honestly thought it was too soft. then i heard it while my mate was driving and i was outside.. big big smile!

bling, cool factor, loving life :thumbsup:

Thanks Perry, will do soon.

[ITRDC2]

thats the way.. j's is the way to go!

the 60RS imo is perfect, doesnt idle too loud, when u fang it it comes alive but normal everyday driving wont even notice it. when i first put it on, i honestly thought it was too soft. then i heard it while my mate was driving and i was outside.. big big smile!

bling, cool factor, loving life :thumbsup:

Thanks Perry, will do soon.

sounds like my toda lol...also make me smile once vtec kicks in...cuz i have the gruppe m as well,actually n1 is the ideal but just too loud for me, and 70rr from j's also too loud, so thats why i want 60rs, if not much difference then i might just keep my toda lol

[namr]

sounds like my toda lol...also make me smile once vtec kicks in...cuz i have the gruppe m as well,actually n1 is the ideal but just too loud for me, and 70rr from j's also too loud, so thats why i want 60rs, if not much difference then i might just keep my toda lol

i've never heard the toda exhaust on the ep3/dc5, the only way and best way would be to hear it in person. is the toda exhaust full titanium?

[ITRDC2]

i've never heard the toda exhaust on the ep3/dc5, the only way and best way would be to hear it in person. is the toda exhaust full titanium?

a few of the members here run toda on their ep3,and the toda is not full titan, only the end tube i think

[Perry]

Is the J's full titanium?
OH yeah anyone from here were on Lane cove rd this morning heading towards Ryde or Chatswood?

[namr]

Yep full titanium 5kgs all up i think.

[KaZe86]

welcome nam,

your brians mate yeah? i seen your car when you first got it far out its come a long way since then where has it been? havent seen it for ages pics man!! =P i got the other cw ep3

[k0e1]

man george u must love korean bbq and welcome namr

[SuperSteve]

man george u must love korean bbq and welcome namr

hahahaha he loves it alright !

[namr]

welcome nam,

your brians mate yeah? i seen your car when you first got it far out its come a long way since then where has it been? havent seen it for ages pics man!! =P i got the other cw ep3

Yeah thanks bro, bankai right?
Its been at home in my area havent been around the city as much and rarely go for cruises
Im waiting for nice weather to give it a wash then ill get some photos. Your te's looking tuff!

[KaZe86]

Yeah thanks bro, bankai right?
Its been at home in my area havent been around the city as much and rarely go for cruises
Im waiting for nice weather to give it a wash then ill get some photos. Your te's looking tuff!

yea man bankai or steve lols

yeah been shit weather bad lately went to wash my car yesterday and fk rained straight after lols maybe ill wash it now ahahaha thanks man wanna spray them though :confused:

[namr]

Oh really what colour, current colour is prime imo

[i-vtec]

anyone have 2nd hand coilovers for sale ?
shoot me a PM ?

[KaZe86]

Oh really what colour, current colour is prime imo

yeah i like the bronze i was thinking of crazy colour like red or orange but yeah will see not to sure atm kinda broke =(

[icecrm]

WORD OF ADVICE, IF YOU GO TO THE BATHROOM, MAKE SURE GEORGE OR STEVE DONT FOLLOW they tend to 'have to go to the toilet' when others do hahahaha

[k0e1]

WORD OF ADVICE, IF YOU GO TO THE BATHROOM, MAKE SURE GEORGE OR STEVE DONT FOLLOW they tend to 'have to go to the toilet' when others do hahahaha

thanks will take that on board and go to the toilet before meeting up hahahha

[Nepolian]

WORD OF ADVICE, IF YOU GO TO THE BATHROOM, MAKE SURE GEORGE OR STEVE DONT FOLLOW they tend to 'have to go to the toilet' when others do hahahaha

You guys aren't seriously believing what this clown is talkin about.......!

You know he is really talkin about himself! Just ask his missus!


thanks will take that on board and go to the toilet before meeting up hahahha

Just watch out for Jimmy the sniper!

[SuperSteve]

yeah when i was sitting at the table when we were at ribs and rumps he had this weird look in his eye, sort of the looking like .... hey you .. i wanna get it on .......

[Nepolian]

yeah when i was sitting at the table when we were at ribs and rumps he had this weird look in his eye, sort of the looking like .... hey you .. i wanna get it on .......

....................................with da chicken.....LOL!

[SuperSteve]

....................................with da chicken.....LOL!

i have to admit that chicken did look pretty tasty !

cant wait for korean bbq this weekend :D start training george its gonna b MASSIVE ! ! !

[Nepolian]

i have to admit that chicken did look pretty tasty !

cant wait for korean bbq this weekend :D start training george its gonna b MASSIVE ! ! !

I set the standards........you know it!

Smell the bulgogi............hmmmmmmmmmmmm

[SuperSteve]

I set the standards........you know it!

Smell the bulgogi............hmmmmmmmmmmmm

hahahha yeah u do

this saturday bro, its on like donkey kong biatch ! ! may the best man win :cool:

[Perry]

hahahah you guys..

[SuperSteve]

hahahah you guys..

hey its on ! u know it ! u better bring it aswell mate !

[Perry]

hey its on ! u know it ! u better bring it aswell mate !

hahaha make sure u dont sleep in hehehe :thumbsup:

[SuperSteve]

hahaha make sure u dont sleep in hehehe :thumbsup:

hahahahaha good call good call :thumbsup:

this time i wont b late :D

[Perry]

hahahahaha good call good call :thumbsup:

this time i wont b late :D

There is no where ill out eat u guys.

[SuperSteve]

There is no where ill out eat u guys.

hehehe :D we will see on saturday aye ;)

[icecrm]

btw guys, went back to RnR for the missus bday and took on...........THE MIX GRILL!!!

hahahaha

so much meat. gave me the meat sweats hahahha

[denrie]

btw guys, went back to RnR for the missus bday and took on...........THE MIX GRILL!!!

hahahaha

so much meat. gave me the meat sweats hahahha

I think I had that aswell when I ate there last. Didn't think I finished it though. lol

[Perry]

Ok guys i need a little help here anyone got pics of a ep3 with Mugen grill and foggies?

[ITRDC2]

http://ekhatch.files.wordpress.com/2008/12/yellow-ep3-203816.jpg

[Perry]

Got any without the lip?? and for prefacelift thanks ITRDC2

[ITRDC2]

http://img154.imageshack.us/img154/7618/m1img0376tj5.jpg

no worries mate, enjoy :)

[Perry]

I'm sold now getting my gril than :thumbsup: more pics ehhehe wonder what rims are they on the red EP3?

[ITRDC2]

im more wonder what will be look like if i take my foggies off and then get the j's style led on :D

[Philip Lee]

that yellow one has pre FL bumper.

[Perry]

that yellow one has pre FL bumper.

Oh yeah just the way I like but without the extended guard add on, Man Philip I cant find that white EP originally one I saw from the site :(

[Philip Lee]

http://a.imagehost.org/0909/p19677441.jpg

is this it (this is off my hdd)? if you saw something u like u gotta save it. it's hard to find it again.

[Perry]

http://a.imagehost.org/0909/p19677441.jpg

is this it (this is off my hdd)? if you saw something u like u gotta save it. it's hard to find it again.

Yep thats the one I saved the photo but I need specs on the wheels wasnt sure if it was 17x8.

[white_ep3_civic]

Ok guys i need a little help here anyone got pics of a ep3 with Mugen grill and foggies?

I will put mine on here soon. Just waiting to get the grille sprayed. As soon as it is finished ill post some pics

[Nepolian]

http://img154.imageshack.us/img154/7618/m1img0376tj5.jpg

no worries mate, enjoy :)


I'm sold now getting my gril than :thumbsup: more pics ehhehe wonder what rims are they on the red EP3?

WOW, ITRDC2..........have you got one without the offset number plate, pre fl front bar, mugen grille without foggies in green with black bonnet and face lift headlights? :p

[Jibz]

WOW, ITRDC2..........have you got one without the offset number plate, pre fl front bar, mugen grille without foggies in green with black bonnet and face lift headlights? :p

hahahahaha that made me laugh.

[SuperSteve]

some nice civics over there in the states
niceeeeeeeeeeee

[Perry]

Any links to more EP3 pics except for ozhonda?, I tried honda-tech no luck.

[Nepolian]

hahahahaha that made me laugh.

LOL....after I said that, I googled "Green Civic EP3" and I got this......pretty close aye?? Dahm, I thouht I was being quite particular!

[Perry]

hahaha h

[Perry]

Whats with the middle section gone on the front bar looks pretty cool.

[NightRyder]

Meet is up guys and gals (if any):

http://www.ozhonda.com/forum/showthread.php?p=2445413#post2445413

Should you need to contact me, I'm on 0411 238 333.

See you there! :)

[Nepolian]

Meet is up guys and gals (if any):

http://www.ozhonda.com/forum/showthread.php?p=2445413#post2445413

Should you need to contact me, I'm on 0411 238 333.

See you there! :)

Yeay :thumbsup:

[EP3-R]

someone may have already answered this (long thread), I'm in need of an oil cap, OEM if possible for my EP3. I don't want to go through Honda coz they're a rip. Anyone know a place in Melb who may stock them or a/m?

P.S. Google has not been my friend so far.

Cheers

[Nepolian]

someone may have already answered this (long thread), I'm in need of an oil cap, OEM if possible for my EP3. I don't want to go through Honda coz they're a rip. Anyone know a place in Melb who may stock them or a/m?

P.S. Google has not been my friend so far.

Cheers

Any K serries honda cap will fit.

[EP3-R]

Cheers mate. I was thinking the same as they all run the K20 however when I was looking through some a/m ones they listed that they'd fit a DC5 etc but had no mention of EP3...

[KaZe86]

http://www.youtube.com/watch?v=RRftVFMi--g :eek:

[SuperSteve]

http://www.youtube.com/watch?v=RRftVFMi--g :eek:

u hoon !

sounds nice :)

[Frost_FD]

Whose selling their white EP3 is on carsales with emotion rims?
WA owner

I'm kind of interested.

[white_ep3_civic]

http://www.youtube.com/watch?v=RRftVFMi--g :eek:

That sounds mad. Wat exhaust hav u got?

[ITRDC2]

http://www.youtube.com/watch?v=RRftVFMi--g :eek:


u changed ur exhaust already??? no more 5zigen?

[denrie]

:( My car got hit from the back today. Damage not too bad but still gona get it fixed!

[Mugen_B16B]

yeah yellow ones got a preface bumper but facelift grille and lights, imo the facelift grille looks crap compared to preface

[KaZe86]

that wasent me lols ahahaha :p

its still the same exhaust 5zigen

[bbds]

stop speeding
lolz hoon

[ep3ken]

sounds great what exhaust is that?

[KaZe86]

few post back its a old 5zigen one

anyone interested in it? i want a toda one ;)

[Rai-C]

yeah yellow ones got a preface bumper but facelift grille and lights, imo the facelift grille looks crap compared to preface

i actually like FL mugen grille.. fatter looking.. does it fit the preface front bar straight up?

ps. US currency exchange rate ftw right now.. im g'd for my US trip hahaha :D

[Rai-C]

:( My car got hit from the back today. Damage not too bad but still gona get it fixed!

=O is my axleback okay? hahaha

[white_ep3_civic]

few post back its a old 5zigen one

anyone interested in it? i want a toda one ;)

If u weren't in a different state I buy it lol

[denrie]

=O is my axleback okay? hahaha

ahahaha all good it's alright :) Just the bumper that got hurt...

[KaZe86]

If u weren't in a different state I buy it lol

get it shipped up xD

[Rai-C]

ahahaha all good it's alright :) Just the bumper that got hurt...

sick hahaha did you end up finding another exhaust yet?

[ITRDC2]

http://img239.auctions.yahoo.co.jp/users/5/1/4/4/rs19751206-img600x450-125181466741uoom67379.jpg

anyone interested?

[denrie]

http://img239.auctions.yahoo.co.jp/users/5/1/4/4/rs19751206-img600x450-125181466741uoom67379.jpg

anyone interested?

How much? PM me :)

[Rai-C]

pm me also :) hahaha im mod-hungry :)

[Malenic1981]

Whose selling their white EP3 is on carsales with emotion rims?
WA owner

I'm kind of interested.

It's one of my best friends car, very good car, it's like brand new

[Mugen_B16B]

How much? PM me :)
ive been at uni all night, 3 redbull cans and now looking at this pic, correct me if im wrong but the mid piping looks like 2inch:confused: or im just tripping out lol

[Nepolian]

ive been at uni all night, 3 redbull cans and now looking at this pic, correct me if im wrong but the mid piping looks like 2inch:confused: or im just tripping out lol

How can you tell how big a pipe is from a picture?

Most JDM cat backs are 60mm (just under 2.5") unless stated otherwise!

[k0e1]

hye guys should i do a wheel alignment after i raised my car straight away? or does it matter at all?

[c1v1c]

hye guys should i do a wheel alignment after i raised my car straight away? or does it matter at all?

Would be advisable. But its really up to you.

[namr]

Anyone here got dc5 Recaro seats in there ep3s? Im thinking of getting a pair but need some opinions thanks

[ep3ken]

http://img239.auctions.yahoo.co.jp/users/5/1/4/4/rs19751206-img600x450-125181466741uoom67379.jpg

anyone interested?

Im interested as well, PM me with price. What brand is it?

[KaZe86]

looks like a mugen to me

[c1v1c]

looks like a mugen to me

It surely does.. Looks just like mine :D.. only cleaner :(

[KaZe86]

any sound clips or photos of it installed on your ep3?

[c1v1c]

any sound clips or photos of it installed on your ep3?


http://ozhonda.com/forum//showpost.php?p=2383728&postcount=4500
There you go. I take delivery sometime next week.. Will get a vid and post it asap if you want?

[ITRDC2]

any sound clips or photos of it installed on your ep3?

Youtube urself lol

[c1v1c]

any sound clips or photos of it installed on your ep3?

http://www.youtube.com/watch?v=v4-Zo0aQmuA&feature=related

[MMike]

This one as well, click! (http://www.youtube.com/watch?v=TrkFKuOd4AQ)

It sounds pretty nice!

[ITRDC2]

bad news....the mugen twin loop is sold to some bidder....sorry guys....that was quick!

[n5920787]

ive been at uni all night, 3 redbull cans and now looking at this pic, correct me if im wrong but the mid piping looks like 2inch:confused: or im just tripping out lol

Man haven't been on forum for awhile, so much to catch up on. I saw your car parked opposite uni last night.

[Mugen_B16B]

How can you tell how big a pipe is from a picture?

Most JDM cat backs are 60mm (just under 2.5") unless stated otherwise!

hahaha nah i think i was just OD on redbull looks normal when i look at it now lol

[Mugen_B16B]

Man haven't been on forum for awhile, so much to catch up on. I saw your car parked opposite uni last night.
yeah had an allnighter study session, where u been man?

[denrie]

Who was that on M4 next to me all the way from Silverwater to Resovoir Rd? Had HJC stickers, CF bonnet, exhaust and the silver tie bar? :)

[EG5]

Who was that on M4 next to me all the way from Silverwater to Resovoir Rd? Had HJC stickers, CF bonnet, exhaust and the silver tie bar? :)

Thats Alex's EP3

[denrie]

Thats Alex's EP3

Who's Alex? Is he on the forum?

[Rai-C]

i think JDMYARD needs a sponsor vehicle doner.. AHEM how bout an EP3, Yonas? hahah

[EG5]

Who's Alex? Is he on the forum?

Not too sure if he is on the forum

[EG5]

i think JDMYARD needs a sponsor vehicle doner.. AHEM how bout an EP3, Yonas? hahah

We need sponsor for our EGK24A

[SuperSteve]

We need sponsor for our EGK24A

haha yonos i have a work truck that drives around with jdm yard stickers on the windows :D

[Mugen_B16B]

send some stickers this way yonas and ill support u lol

[denrie]

Not too sure if he is on the forum

Ohh ok thanks. We were next to each other for awhile. Crazy driver aswell. LOL

[Nepolian]

Ohh ok thanks. We were next to each other for awhile. Crazy driver aswell. LOL

Crazy driver......who, you or him?......you said you "were next to each other for awhile!"

Who kept up with who? LOLS!

[SuperSteve]

vtec yo !

[k0e1]

speeding isnt a crime until you get caught. right? hahha

[denrie]

Crazy driver......who, you or him?......you said you "were next to each other for awhile!"

Who kept up with who? LOLS!

He was, dodging through cars at around 160km/h. Then i'll just catch up to him again and stay next to him. We didn't race. lol and don't think he's from he forum. He had cf bonnet, intake, exhaust, and the tie bar at the rear of the car similar to beaks.

[Mugen_B16B]

hahaha dont lie u no the ep3 makes u drive like a hoon, look at steven [kaze86]

[denrie]

hahaha dont lie u no the ep3 makes u drive like a hoon, look at steven [kaze86]

ahahaha nah I don't really drive like a hoon. I admit I do sometimes but rarely now. LOL unless I'm with a whole bunch of friends with there cars.

[icecrm]

peer pressure is a bitch aye.....LOL

[Mugen_B16B]

i surely agree there LOL

[denrie]

peer pressure is a bitch aye.....LOL

Yeah man hard! ahahaha

[KaZe86]

hahaha dont lie u no the ep3 makes u drive like a hoon, look at steven [kaze86]

WTF?!?! your a HOON!!

[SuperSteve]

You all a bunch of hoons ! *cough* hey guys question, when u take ur first gear 2 redline and quick switch 2 second, does it go in smoothly or sometimes does it not want to go in and crunches ?

[KaZe86]

You all a bunch of hoons ! *cough* hey guys question, when u take ur first gear 2 redline and quick switch 2 second, does it go in smoothly or sometimes does it not want to go in and crunches ?

smooth baby like silk... lols :p

[icecrm]

rough like.......a rough surface

[EP3-R]

I find it depends on how i shift it. If i force it in it feels like it crunches a bit. I find when i "pull" the shifter back it goes in easier as opposed to "pushing" it back if ya know what i mean?

[Philip Lee]

never redline in 1st so i dunno hahaha

[KaZe86]

has anyone by anychance got a front lip hanging around?

i was looking at some ep3 pictures and it seems my front lip is missing that black plastic part that covers the front tabs under the front bar anyone know what im talking about?

[n5920787]

yeah had an allnighter study session, where u been man?

Yeah been busy with work/uni. i ono i went through a phase where i wanted to move on to a luxury car. Just lost all the motivation i had with the car when i first got it

[bbds]

sorry to hijack thread, but has anyone heard of OBX ITB for ep3s before?

[gd1_nz]

does anyone know if the EP3 rails are the same as the Dc5 ones? thanks

[denrie]

sorry to hijack thread, but has anyone heard of OBX ITB for ep3s before?

I've heard of it but thats about it.


has anyone by anychance got a front lip hanging around?

i was looking at some ep3 pictures and it seems my front lip is missing that black plastic part that covers the front tabs under the front bar anyone know what im talking about?

Yeah I know what your talking about. I know a few ppl that doesn't have it in there EP's aswell.

[Philip Lee]

does anyone know if the EP3 rails are the same as the Dc5 ones? thanks

i'd assume they're the same but i dont know 100%.

[Nepolian]

rough like.......a rough surface

Nop, rough like ur head....LOLS!

Hey Jimmy, this is for you!

Lunch meet!

BEFORE,

http://i31.tinypic.com/9rh8h2.jpg

AFTER,

http://i32.tinypic.com/161guwm.jpg

[Perry]

Nop, rough like ur head....LOLS!

Hey Jimmy, this is for you!

Lunch meet!

BEFORE,

http://i31.tinypic.com/9rh8h2.jpg

AFTER,

http://i32.tinypic.com/161guwm.jpg

ahahha Steve walkd into the females bathroom didnt he?

[denrie]

George how come your selling your Brembo set!?

[Nepolian]

George how come your selling your Brembo set!?

Cause I'm eyeing off at a set of rims atm :p

I'll get over it soon and keep the Brembos....Oh Im so confused!

[denrie]

What rims? :) Tell us! ahaha

[k0e1]

Maybe Works 18" =P

[Perry]

Ce28's

[SuperSteve]

Cause I'm eyeing off at a set of rims atm :p

I'll get over it soon and keep the Brembos....Oh Im so confused!

dont do it mate. U can always wait for rims lol :D not like u need them anyways ! ! you impulse buyer you ! ! haha jokes

[Nepolian]

dont do it mate. U can always wait for rims lol :D not like u need them anyways ! ! you impulse buyer you ! ! haha jokes

O'Rly....you think so too!