EP3 Type R

[Poeter]

Pete, do u need a Japanese windows to run that??

It's actually a virtual machine with Windows in Russian preloaded with the EPC. So will need
vmware player to use it.

The reason it's setup this way is because the software licence activation is locked down to this virtual machine.

[keepitlow]

Haha all good Kevin~ : )

[itachi-kun]

With my whiteline camber bolts, the washer tabs sit the same as the ones picture above, the tab faces inwards. From what I saw, when I installed them the washer can only sit at one position to the bolt i.e. the washer locks the bolt. When you spin it, it will spin the bolt/lobe as well.

My initial camber reading measured at -1.08 (camber tops were maxed out), I forgot to tell the guys at Jax I had the camber bolts. They did a second alignment and got -2.4 out of them.

Thanks for the reply. My mate spun the bolt around and what do you know... it pushed the top of the hub in, adding neg camber. Stupid jax.

[Philip Lee]

It's actually a virtual machine with Windows in Russian preloaded with the EPC. So will need
vmware player to use it.

The reason it's setup this way is because the software licence activation is locked down to this virtual machine.

wow so complicated but worth the efforts i guess.

[Poeter]

it's good to have handy. Smash repairers won't have the excuse that they can't find parts.

[goatpaste]

This may sound like a strange question, but how many kms do you guys think the rubber on an ep3 clutch pedal would last before it wears out?

I only ask because I had a look at a car on the weekend with very low kays but the clutch pedal rubber was completely worn through. Should I be suspicious?

[Twest]

Hey guys,

I put my 235/45/17 semi's on today and the rear is scrubbing...I used a mallet and heatgun and rolled the rear guards asmuch as I could so they were nearly flat against the inside of the guard however the rear still scrubs. I'm running Aragosta Coilovers dropped around 1.5-2inches all around. I even stiffened up my ridiculously hard coilovers all the way and it still scrubs.

Alignment for rear:

Camber: -2.62 and -2.34 LH/RH respectively

What else could I do to stop it from scrubbing?> I was thinking about rasing the rear 5mm-10mm and see if it stops rubbing. I am going to a trackday on monday and really don't want it to chew through my new semis :(

[Twest]

Also it's mainly the right hand side that's scrubbing the left isn't scrubbing as much...Unforunately I don't have adjustable camber arms either..Not that you would want more than 2.3-.5 of camber anyway.

[Johnassan]

Also it's mainly the right hand side that's scrubbing the left isn't scrubbing as much...Unforunately I don't have adjustable camber arms either..Not that you would want more than 2.3-.5 of camber anyway.

It's prob scrubbing on the inside (on your coils itself)

[Twest]

It's prob scrubbing on the inside (on your coils itself)

No the inside is fine, it's the outside. I can see the mark from where it is scrubbing.

[Symphorced]

How are you getting that much camber without adjustable camber arms in the rear?

[Twest]

How are you getting that much camber without adjustable camber arms in the rear?

I honestly don't know, I'm assuming these aragosta coilovers for the dc5 are somehow causing it to camber more...Even the guy at jax said it was unusual.

[Symphorced]

I have the Hardrace camber kit at the rear and one side maxed out at -2.1 degrees. :/

[[daan]]

yeh raise it up man see if it helps

[Twest]

I have the Hardrace camber kit at the rear and one side maxed out at -2.1 degrees. :/

...well this is awkward.

[Twest]

;3164902']yeh raise it up man see if it helps

Yea I'll try that and see how I go...I can't find my damn cspanners.

[Twest]

I have a strong feeling the jax alignment machine was ****ed..Those numbers just don't sound right.

[Lukezen27]

I have a strong feeling the jax alignment machine was ****ed..Those numbers just don't sound right.

I'm with Twest

That seems backwards to me

[Twest]

I am running dc5 suspension however luke...Do you think that the dc5 coilovers have a different geometry?

[Twest]

Because according to the jax machine I am getting 2.3degs LH and 2.78degs RH camber...That definetely sounds off. OR...the coilovers somehow changed the geometry alot.

[Lukezen27]

So no one’s got any better instructions or diagrams on installed the air spoiler under the front bumper?


I am running dc5 suspension however luke...Do you think that the dc5 coilovers have a different geometry?

you might be on to something there Twest

dc5 coilovers or actual OEM dc5 suspensio?

Benny will know!

BENNNY do ya thing?

[Twest]

dc5 coilovers not oem, I have a strong feeling it is that. Put the car onto my mechanics wheel alignment gear and same results.

[keepitlow]

So no one’s got any better instructions or diagrams on installed the air spoiler under the front bumper

luke see if the below link can be of any help~ :D

http://www.hondaoriginalparts.com/honda_car_parts_large_image_C50.php?block_01=17S5S 01&block_02=B__4601&block_03=9511

[Symphorced]

So no one’s got any better instructions or diagrams on installed the air spoiler under the front bumper?


I just ordered a universal one. Probably going to just sikaflex it on somewhere down there. If not... RIVET GUN! Will let you know how it goes next week. How come you took your one off btw?

[RPS.13]

So no one’s got any better instructions or diagrams on installed the air spoiler under the front bumper?

Best I could do with the images I have: (sorry I couldn't make it any bigger) again the scanned quality isn't great!

http://i613.photobucket.com/albums/tt212/KAIZENRPS_13/frontairspoiler.jpg?t=1322401867

Bit hard to describe, but the lip slots into bumper. Just under that there is a raised edge which is held in place by plate(s), that have a 10mm bolt(s) holding them in place.

You could probably get away with cable ties or self tapping screws.


I just ordered a universal one. Probably going to just sikaflex it on somewhere down there. If not... RIVET GUN! Will let you know how it goes next week. How come you took your one off btw?

Self tappers would be a lot easier, or cable ties if your lazy!

[Lukezen27]

Best I could do with the images I have: (sorry I couldn't make it any bigger) again the scanned quality isn't great!


Bit hard to describe, but the lip slots into bumper. Just under that there is a raised edge which is held in place by plate(s), that have a 10mm bolt(s) holding them in place.

You could probably get away with cable ties or self tapping screws.



Self tappers would be a lot easier, or cable ties if your lazy!

Thanks dude

Bit clearer seems I'm missing the top plates

Got the 10mm bol and bottom plates

[NightRyder]

Oo..Oo...where can I get one of these air spoilers??.. :)



Best I could do with the images I have: (sorry I couldn't make it any bigger) again the scanned quality isn't great!

http://i613.photobucket.com/albums/tt212/KAIZENRPS_13/frontairspoiler.jpg?t=1322401867

Bit hard to describe, but the lip slots into bumper. Just under that there is a raised edge which is held in place by plate(s), that have a 10mm bolt(s) holding them in place.

You could probably get away with cable ties or self tapping screws.



Self tappers would be a lot easier, or cable ties if your lazy!

[Symphorced]

Oo..Oo...where can I get one of these air spoilers??.. :)

They come stock with the car?

[JohnO]

^ i like your rims man bbs's? if so what specs

[Symphorced]

^ i like your rims man bbs's? if so what specs

Thanks mate. Yeh BBS LM. 17x9 +20.

http://www.gripshiftslide.com/photos/jdm_meet/ep3_honda_civic.jpg

[NightRyder]

not mine, hence why i asked! :)

They come stock with the car?

[Symphorced]

not mine, hence why i asked! :)

Any home depot store (Bunnings). Just a garage door lip. :p

Otherwise if you cbf searching:

http://maxvisionaus.blogspot.com/2011/03/universal-front-bumper-lip-splitter.html

[[daan]]

car looks hot with the BBS' man

[RPS.13]

After dinner tonight, I noticed my battery light had turned on, my gf pointed out the speedo wasn't working and also the EPS light came on!!! I did notice the steering being a tad heavier than normal and the car felt a lil sluggish at first before I noticed anything.

So glad I found this thread on the 3rd google link I opened: problem-check-engine-light-battery-light-speedometer.html (http://www.civicforums.com/forums/182-7th-gen/311660-problem-check-engine-light-battery-light-speedometer.html)

Got the torch onto the fuses under the steering column and what do you know, I had blown a 10a fuse. I'm assuming it is the alternator one. The diagram on the fuse panel says to look at the manual. I swapped the fuse and everything is working fine now.

As mentioned in the link, does anyone know if the alternator could be stuffed? Hence, blowing the fuse???

Anyone else had the same issue?

I think i'll be changing my secondary o2 sensor soon, just in case I get another CEL light coming up for something else!

[Symphorced]

I freak out so much every time the CEL comes on. I'd probably crash the car if the CEL popped up while I was driving haha. Did the manual confirm that it was the alternator fuse?

Also, in regards to the prior topic of conversation. Got the front underspoiler on. As it's a universal one, sort of just used self tapping screws and screwed them into the plate and then trimmed the edges of the lip to try and match the OEM one. Definitely a case of good from afar but far from good. Will post photos tomorrow.

[RPS.13]

I freak out so much every time the CEL comes on. I'd probably crash the car if the CEL popped up while I was driving haha. Did the manual confirm that it was the alternator fuse?

I don't have a copy of the manual. I think it was fuse no 4:
http://i120.photobucket.com/albums/o164/joe_0_1/utf-8BSU1HMDAzNzMtMjAxMDEwMjgtMTM0NS5qcGc.jpg

Anyone have a copy of the manual? or can anyone confirm the fuse numbers above? the ones that refer to the book.

My CEL has been on for a while now and I have kind of forgotten about it. I know how you feel though!

[p3p5y]

Hey guys,

Any ideas on where I can purchase aluminium shifter cable bushings kit for the EP3? This is the bushings that you replace underneath the hood, below the stock air filter.

Just installed aluminium gear shifter bushings under the gear knob today. There is a marginal difference - more solid, but I feel it can be further improved.

Cheers.

[PeppeX]

Bought mine from here www.corsportusa.com/store/catalog/index.php?cPath=1_17&osCsid=f455b5511bb81eeadd725111bb5c1c24

But the Shifter base bushings made a bigger difference than the cable bushings.

[p3p5y]

Thanks Peppex. Are there any differences between cheaper aluminium cable shifter bushings that find on say, eBay for $30 compared to the anodized, branded ones such as Hybrid racing (~$70)?

[PeppeX]

Not sure, but I think Corsport ones will be fine as they are a big shop in the US. Try to get from a power seller on ebay which also sell other quality parts.

[bennjamin]

guiz


whats involved with replacing PFL headlights with FL headlights ?!

Standard PFL are shocking. Well , my standard bulbs are shit and just about dead.

[bluey45]

guiz


whats involved with replacing PFL headlights with FL headlights ?!

Standard PFL are shocking. Well , my standard bulbs are shit and just about dead.

Yeah I'm also quite interested as well was thinking either change headlights or get fogs. I think for both the left and right FL headlights cost about $1k. But if you already have the d2r bulbs will they work? Do they come with the ballast?

[JohnO]

i changed mine and it was a straight swap Ben just needed to separate the hi and lo cables and solder it onto the fl headlight cables, you'll end up having a spare set of wires hanging which isnt needed for the fl ones but if you ever decide to change back you'll need to keep them on or else cut them off. sorry i dont know how else to explain it, was just using a volt meter and checking which wires were which and connecting it through trial and error and the end result was decent. i bought mine from a mate for about 700 bucks with oem ballasts but now its been sold to winry :'(

[bluey45]

i changed mine and it was a straight swap Ben just needed to separate the hi and lo cables and solder it onto the fl headlight cables, you'll end up having a spare set of wires hanging which isnt needed for the fl ones but if you ever decide to change back you'll need to keep them on or else cut them off. sorry i dont know how else to explain it, was just using a volt meter and checking which wires were which and connecting it through trial and error and the end result was decent. i bought mine from a mate for about 700 bucks with oem ballasts but now its been sold to winry :'(

Hey Johno. I heard you selling your EP3? Will you be parting out some parts?

[JohnO]

i wanna get rid of it with all the mods cause im lazy to take it off

[Perry]

We will strip it off ya hehehe

[keepitlow]

^^ interested in parting out John :)

make some quick cash with the parts!

[bluey45]

Yeah I'm interested as well. :)
Will be glad to get some parts off ya

[keepitlow]

Kev, done much to your car lately? :)

[Perry]

alot of ppl are selling up *sigh*

[keepitlow]

I'll be keeping my for a while :) love it as a daily..

[bluey45]

Kev, done much to your car lately? :)

Hey Danny. How are ya? :)
I haven't done much except get my beaks tie bar and replaced wipers lol. Well tomorrow im going to get my clutch replaced and get my front slotted rotors installed.

How about yourself?

[Perry]

Same till I find a better car for a long term project.

[bluey45]

alot of ppl are selling up *sigh*

I'll be keeping mine as well for a while. Great car to drive for occasional driving. :)

[bluey45]

I'll be keeping my for a while :) love it as a daily..

Hey dan. Didn't get to say hi to you at club itr bbq. You popped in so fast with your evo x! =p

[Blackep3]

Got my new light in today boys....

[bluey45]

A good write up:

http://pub161.ezboard.com/fbseriesalternativefrm7.showMessage?topicID=166.to pic

Ooo. Nice did you get the facelift lights Paul? Pics!:)

[keepitlow]

lol yahh I didn't realise you were there :)

I just drop off the shift boot and had to go see gf.. wish I could stay, was a great turn out!

hahaa I haven't done much to my car... except restoring some interior parts..

[cskfai]

Sigh..I have just returned from hometown. Bad news..I found that the gruppeM intake, GPS, floor mat, gear knob and sunglasses were stolen :( F**K!!!!

[Bludger]

alot of ppl are selling up *sigh*
P platers downgrading to bitsRmissing evo 7/8/9

when they get off their P plates.

[Poeter]

Sorry to hear.

They didn't take your recaros?

[Lukezen27]

they didn't even have Ps when i got my licence lol

[Bludger]

they didn't even have Ps when i got my licence lol
was a time when true freedom prevailed.

[Symphorced]

Sigh..I have just returned from hometown. Bad news..I found that the gruppeM intake, GPS, floor mat, gear knob and sunglasses were stolen :( F**K!!!!

Where was the car parked? Sounds like the thieves knew what they were looking for. Scums.

[RPS.13]

Who the f**k steals floors mats??? that's just low!

[cskfai]

Sorry to hear.

They didn't take your recaros?

Yup they didn't. But they stole my spoon sock as well :(



Where was the car parked? Sounds like the thieves knew what they were looking for. Scums.

I parked it in the car park of my apartment. They drew a dick on the dust!! F**K!
Cop told me not to touch any thing on my car and they will come to have inspection today but they didn't come....



Who the f**k steals floors mats??? that's just low!

I want to know too. I have to find where I can buy the floor mat!

[cskfai]

there is another ep3 in my carpark but it was crashed. No idea why they didn't break in his car.

[Symphorced]

Floor mats contact:

http://www.ozhonda.com/forum/showthread.php?155490-now-parting-ep3r-ITR-GearBox-added-parts-garage-clearout-all-prices-are-negotiable

Personally, I'd be having a good think about the "friends" you keep around you.

1. They knew exactly what to look for (gruppeM, floor mats)
2. Broke into your car and not the other EP3
3. Knew you were away(?)

[Poeter]

Usually the first thing ppl steal from type r's are their recaro seats not the useless things like mats and spoon socks.

Some weird theives.

But i agree with symphored, it might be someone you know who doesn't get along with you well.

[Bludger]

Usually the first thing ppl steal from type r's are their recaro seats not the useless things like mats and spoon socks.

Some weird theives.

But i agree with symphored, it might be someone you know who doesn't get along with you well.
druggies, not planing on stealing anything, but just opportunistic.

saw the car there for a few days and then break in and take whats not bolted down.

they wouldn't know the value of recaro's/.....

[cskfai]

Floor mats contact:

http://www.ozhonda.com/forum/showthread.php?155490-now-parting-ep3r-ITR-GearBox-added-parts-garage-clearout-all-prices-are-negotiable

Personally, I'd be having a good think about the "friends" you keep around you.

1. They knew exactly what to look for (gruppeM, floor mats)
2. Broke into your car and not the other EP3
3. Knew you were away(?)

The floor mats have sold but thanks anyway!
I have already found other way to buy.

I agree with you too but I have no idea who did it.
Next time I wont leave my car alone when I return to hometown.
And I have suggested the owner corporation to install CCTV in the car park.


Usually the first thing ppl steal from type r's are their recaro seats not the useless things like mats and spoon socks.

Some weird theives.

But i agree with symphored, it might be someone you know who doesn't get along with you well.

Luckily they didnt steal my recaro!

[Twest]

Yup they didn't. But they stole my spoon sock as well :(




I parked it in the car park of my apartment. They drew a dick on the dust!! F**K!
Cop told me not to touch any thing on my car and they will come to have inspection today but they didn't come....




I want to know too. I have to find where I can buy the floor mat!

My guess is some dodgey thieving bastards have bought an ep3. They don't have floormats, they have a stock airbox and wanted a new gearknob.
Sigh... pricks.

[Lukezen27]

Guys

Got a leak somewhere

Water in the BOOT

Anyone had this problem,,,?

HELP

[chauster]

Guys

Got a leak somewhere

Water in the BOOT

Anyone had this problem,,,?

HELP

Luke, I don't have an ep3 but in my experiences most book leaks are either bad boot/tailgate seals, rubber plugs on the boot floor or tail lights loose or broken.

First try to source where it's coming from. If can't find then look at your seals if worn or broken. Then check your taillights. If they have condensation in them then they will be leaking water in. If not then remove your boot interior and check I all the rubber plugs are in.

Good luck byuddy

[stienerv2]

Yeah I've recently seen a dc5r with the same problem. In his case was that the rubber seals of one of his taillights was gone.

[[daan]]

Lucky its an Ep3. Put the rear seats flat, jump in the back with the tailgate shut and get a mate to spray it with a hose ..inspect... I would say rubbers or tail lights

[bennjamin]

Guys

Got a leak somewhere

Water in the BOOT

Anyone had this problem,,,?

HELP

Check the welding in the boot , check the central plug welded under the spare wheel - water can flick up under during extended periods of driving in the rain. It can easily get in around the small holes and sit in ur boot

[icecrm]

man my central locking is screwed. when i unlock door with remote, it only unlocks passenger door and boot but doesn't lock. when i use key it doesn't lock passenger but unlocks driver side door. parkers are out, tail ight is out. KILL ME hahahhaa

[denrie]

Yeah that's common with our cars. Same as mine! Lol but no problem with the parking lights. Haven't heard from you in a while!

[Perry]

Havent heard from you in ages Denrie where u been?

[KIKNHRD]

I know this isn't the right place to post this but this is the only area I have posted. I rang hondworld on Monday asked for a sun visor drivers side for my ep3 they said no worries $25 for visor and $25 for airbag to Darwin. Arrived Thursday, was totally wrong shape will never fit and look half ok. Rang then back 2 times on Friday, someone was meant to get back but nothing. I have just got off the phone with the manager. He had a go at me saying I got what I ordered and how did I expect him to have a one off an ep3. He then said to send item back and that he would give me a refund. I said to him, "you want me to spend $50 on postage and end up with no visor??" He then said "If I want to play the tough man game" in a real aggressive tone. Then hangs up on me. I have been shopping with then for a few years no and service has been awesome. I will never deal with them again and I will most diffidently stop recommending them to offers.

[KIKNHRD]

Same happened to me I ordered a continuator was quite basic to fit. After a quick youtube lesson

[keepitlow]

Guys, thought I'd share this.. being working on fix rattles from Door Trim.. if your EP3R have this then feel free to read on : )

You will need to remove your door trim to do so, follow this link as the video shows you how to do this: http://importtuningtv.powertvonline.com/user_video_detail.php?mId=1111

Remember when pulling off the trim piece, work your way fron the bottom where there's a gap for you to slide your fingers in.. gentlying slide your fingers around to remove each of the clip, now be gentle so you don't break any plastic bits holding the clip..

This is what I used, a seal tape and table leg protectors from Bunnings..
Also I bought new clips from Honda Parts Australia, they are $5.10 each..

Now this is what the white clips look like that is located around the border on the door trim.. below image is an old one I pulled off, from time to time these plastic clips loose its tension and especially if you've being pulling these off many times to instal your speakers or such then these clips get looses its tension and will not clip hold tight enough..
http://i206.photobucket.com/albums/bb207/dannyhsu/02.jpg

You can see the clips are nice and firm and not crooked like old ones, now before you put them on.. I actually used seal tapes around maybe 3-4 rounds on the ring part where you will be putting back on your door trim.. by doing so its tighten up the clip to the plastic holder on your door trim(I did this with my old car before, so I know it works). Below images for your reference..
http://i206.photobucket.com/albums/bb207/dannyhsu/03.jpg

Your can see now the parts where its used to hold is not thicker, reason for using the seal tape its cos its soft and will absorb a bit of pressure..
http://i206.photobucket.com/albums/bb207/dannyhsu/04.jpg

Now also, when you pull off the door trim.. inside you will see some old cloth piece(mine was pretty much fallen off) I actually replaced all these cloth pieces with these table leg protectors. Comes in a big roll around $11 from Bunning.. now just need to cut these up into sizes and stick them on each part where the plastic touchs the metal..
http://i206.photobucket.com/albums/bb207/dannyhsu/01.jpg

Take your time and Good luck DIY fixing! :)

[bennjamin]

How do we Trip the clutch switch ? Just splice and connect the wires or ?

[JohnO]

I'll ask my Mechanic what he did to mine

[Lukezen27]

How do we Trip the clutch switch ? Just splice and connect the wires or ?

Yeah that whole put the clutch in the starts really annoying lo

Got my new 02 in and Adrian's turned her in...

Lets see how my QLD run goes on gas :p

[stienerv2]

I've fixed my windows today. It ended being the switch and not the motor. Lucky it wasn't the motor because that would of been expensive to replace.

[bluey45]

That's good news! At least u pay the entry fee to the park now =p

[Poeter]

I've fixed my windows today. It ended being the switch and not the motor. Lucky it wasn't the motor because that would of been expensive to replace.


Nice you can finally go through maccas drive thru lol.

Motor is not all that expensive. It's about $100 from UK including shipping.

[Bludger]

Guys, thought I'd share this.. being working on fix rattles from Door Trim.. if your EP3R have this then feel free to read on : )

You will need to remove your door trim to do so, follow this link as the video shows you how to do this: http://importtuningtv.powertvonline.com/user_video_detail.php?mId=1111

Remember when pulling off the trim piece, work your way fron the bottom where there's a gap for you to slide your fingers in.. gentlying slide your fingers around to remove each of the clip, now be gentle so you don't break any plastic bits holding the clip..

This is what I used, a seal tape and table leg protectors from Bunnings..
Also I bought new clips from Honda Parts Australia, they are $5.10 each..

Now this is what the white clips look like that is located around the border on the door trim.. below image is an old one I pulled off, from time to time these plastic clips loose its tension and especially if you've being pulling these off many times to instal your speakers or such then these clips get looses its tension and will not clip hold tight enough..
http://a3.sphotos.ak.fbcdn.net/hphotos-ak-snc7/379118_10150431387051120_647006119_9252080_8293916 57_n.jpg

You can see the clips are nice and firm and not crooked like old ones, now before you put them on.. I actually used seal tapes around maybe 3-4 rounds on the ring part where you will be putting back on your door trim.. by doing so its tighten up the clip to the plastic holder on your door trim(I did this with my old car before, so I know it works). Below images for your reference..
http://a4.sphotos.ak.fbcdn.net/hphotos-ak-snc7/374341_10150431387606120_647006119_9252084_1413924 483_n.jpg

Your can see now the parts where its used to hold is not thicker, reason for using the seal tape its cos its soft and will absorb a bit of pressure..
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/402342_10150431387171120_647006119_9252081_2697654 52_n.jpg

Now also, when you pull off the door trim.. inside you will see some old cloth piece(mine was pretty much fallen off) I actually replaced all these cloth pieces with these table leg protectors. Comes in a big roll around $11 from Bunning.. now just need to cut these up into sizes and stick them on each part where the plastic touchs the metal..
http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/393808_10150431387396120_647006119_9252082_1699025 027_n.jpg

Take your time and Good luck DIY fixing! :)
+rep to you sir.

[ouch]

hey did the ep3 come out in yellow?

[JohnO]

i think the uk/jdm

white,black,grey,red

usdm would have blue ontop dont think yellow was included

[UNA91]

EP3 is due for a general 85000km service. A mechanic wanted to charge more just cause hes never heard of the ep3 and its imported... what do you guys think of 999Automotive in Brisbane? They seem to be a known trader and distributor of many aftermarket parts, and deal with alot of performance and import cars... might give em a try?

[ouch]

What about sunroofs on ep3s?

[Perry]

What about sunroofs on ep3s?

I have thought of the same thing a while ago but some body said it won't be too good for chasis.

[stienerv2]

Plus glass is heavy yo...

[Adjacent]

Sunroof is the ingredient for your typical homochariot.

[JohnO]

The point of a type r is to be weight reduced. Sunroof gets the bitches
















Natsrs. Don't bother man its intended to goto trackdays and not hardparked. Don't need no sunroof

[PeppeX]

Just got some new tyres Kumho KU39, since they got good reviews. On door seal says the tyre pressure should be 35psi front and 33psi rear, so thats what i did. But there is tyre squeal when turning at moderate speed. What pressure do you guys run on street?

[Philip Lee]

I ran 36/34.

Maybe your new tyres need running in.

[bennjamin]

Just got some new tyres Kumho KU39, since they got good reviews. On door seal says the tyre pressure should be 35psi front and 33psi rear, so thats what i did. But there is tyre squeal when turning at moderate speed. What pressure do you guys run on street?

IF the tyres are the same size as oem ( 205 / 45 / 17) then follow what the door sill says - dead cold !

[RPS.13]

36 all round.

Tyre running a few different pressures, i.e. a few psi higher or lower than what is listed and pick something your happy/comfortable with. Different people will always have different preferences with tyre pressures.

[Poeter]

lol i run 38 all around

[JohnO]

36 all round, so hard selling ep3s :(

[stienerv2]

A guy wanted to buy my car at work today. I had to keep telling him im keeping it for a while and also mention him to check out ozhonda and check out your car and Bens too.

No means no god dammit! lol

[iQQ]

hey guys, any of you guys know what the part number for the pre fl headlights are?

[bluey45]

Does anyone know where I can get the fog light brackets for a pre fl EP3?

[keepitlow]

^^ Kevin.. go here if you want originals~

http://www.hondaoriginalparts.com/honda_car_parts_selection_pfk.php?block_01=17S5S01&block_02=08V3102&block_03=9511

or alternatively, can have a look on ebay price is alot cheaper there! : )

[bluey45]

Cheers Danny. I totally forgot about that website.

[RPS.13]

hey guys, any of you guys know what the part number for the pre fl headlights are?

Left: 33 151-S5T-G01
Right:33 101-S5T-G01

Located from here: http://japancars.ru/cat/honda/index.php?hmodtyp=8337,8338&npl=17S5S01&_nplgrp=3&nplblk=B__0800

Googled the part numbers and they also come up in here: http://www.hondaoriginalparts.com/honda_car_parts_selection.php?block_01=17S5S01&block_02=B__0800&block_03=9668

[iQQ]

Left: 33 151-S5T-G01
Right:33 101-S5T-G01

Located from here: http://japancars.ru/cat/honda/index.php?hmodtyp=8337,8338&npl=17S5S01&_nplgrp=3&nplblk=B__0800


Googled the part numbers and they also come up in here: http://www.hondaoriginalparts.com/honda_car_parts_selection.php?block_01=17S5S01&block_02=B__0800&block_03=9668


+1 for you! thanks man

[will13]

reckon we should have a separate sticky for all the EP3 parts sites?

[Blackep3]

hey guys, any of you guys know what the part number for the pre fl headlights are?

I have a pair of pre face lift light if you want 2nd hand of course

[Perry]

reckon we should have a separate sticky for all the EP3 parts sites?

I will be doing that during the week.

[Blackep3]

Perry make me a member please

[JohnO]

Find me a post Paul ill rep you

Generally two blockers and above who rep count not sure about mods

Sent from my HTC Incredible S using Tapatalk

[bennjamin]

Find me a post Paul ill rep you

Generally two blockers and above who rep count not sure about mods

Sent from my HTC Incredible S using Tapatalk

do that and ill ban you :)

[JohnO]

I was joking Ben :)
I never rep anyways too lazy

Sent from my HTC Incredible S using Tapatalk

[bennjamin]

I was joking Ben :)
I never rep anyways too lazy

Sent from my HTC Incredible S using Tapatalk

i am too :) But hopefully kids take notice and dont abuse the system lol !

[JohnO]

I better scoot out of here Hahaha

How's the sale going Ben?

Sent from my HTC Incredible S using Tapatalk

[Symphorced]

Perry make me a member please


I highly doubt a mod would just "make" you a member. You need to make contributions and helpful posts before someone will give you a rep. Took me ages to get my first rep too so I know how you feel.... Though I just went through the last three pages worth of your posts and wasn't able to find anything even close to rep worthy...

[JohnO]

Took me almost a year

Sent from my HTC Incredible S using Tapatalk

[bennjamin]

I better scoot out of here Hahaha

How's the sale going Ben?

Sent from my HTC Incredible S using Tapatalk

rofl -dribs and drabs -but anyway im not in too much of a rush as i actually dont have another car set 100%.
DC2R or MK6 gti golf or FT86 or 1M or . . . dunno lol

[stienerv2]

Since you still have the ep Ben come to our meet lol. You said you wanted to cruise to the city sometime with us too

[JohnO]

rofl -dribs and drabs -but anyway im not in too much of a rush as i actually dont have another car set 100%.
DC2R or MK6 gti golf or FT86 or 1M or . . . dunno lol

definitely 1M! i dont get why they didnt label it as m1... cough scirocco

[stienerv2]

M1 is already taken by the old school supercar coupe.

[Blackep3]

Fair enough boys I understand.

[Symphorced]

rofl -dribs and drabs -but anyway im not in too much of a rush as i actually dont have another car set 100%.
DC2R or MK6 gti golf or FT86 or 1M or . . . dunno lol

Ballin! Haha.

[Mikeyy168]

^^ Kevin.. go here if you want originals~

http://www.hondaoriginalparts.com/honda_car_parts_selection_pfk.php?block_01=17S5S01&block_02=08V3102&block_03=9511

or alternatively, can have a look on ebay price is alot cheaper there! : )

mate, you rock. ive been looking for headlights for a while. THANKS!

[keepitlow]

mate, you rock. ive been looking for headlights for a while. THANKS!

No worries mate,

here's the link for all parts from my previous post~ :)

For Pre-facelift Model go here:
http://www.hondaoriginalparts.com/honda_car_parts_block_selection_C30.php?mod_01=951 1

For Facelift Model go here:
http://www.hondaoriginalparts.com/honda_car_parts_block_selection_C30.php?mod_01=972 5

[Lukezen27]

Well my leak fixed its self lol

Hasn't leaked for over a week now....

[bennjamin]

Well my leak fixed its self lol

Hasn't leaked for over a week now....

That's because you haven't pissed in the boot since !

[mr_kentu]

hi all, im just new about ep3. got question.
is there any direct replacement for hid bulb and balast for 2002 ep3 ? 1 of my headlight is not working :(

** i found the answer from the earlier post in this thread. i search on ebay and i found this
http://www.ebay.com.au/itm/Philips-HID-D2S-D2R-D2C-Xenon-Bulbs-8000K-Honda-S2000-/260655586416?pt=AU_Car_Parts_Accessories&hash=item3cb0489c70
it says for honda s2000. will it be the same ?

[keepitlow]

Just bumped into this while I was searching for some light bulb size for EP3R

EP3 Pre-Facelift

Headlights: H4 (Main and Dipped) Dual Filament
Front Position Light: 501 / 194 / T10
Front Indicator: Offset Pin BAU15S
Front Fog Lights: H11
Side Repeater: 501 / 194 / T10
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: 382 / P21W
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10


EP3 Facelift

Headlights: H1 (Dipped), HB3 (Main)
Front Position Light: 501 / 194 / T10
Front Indicator: T20
Front Fog Lights: H11
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: W2 / 921 / 912 / T15
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10

[Lukezen27]

Just bumped into this while I was searching for some light bulb size for EP3R

EP3 Pre-Facelift

Headlights: H4 (Main and Dipped) Dual Filament
Front Position Light: 501 / 194 / T10
Front Indicator: Offset Pin BAU15S
Front Fog Lights: H11
Side Repeater: 501 / 194 / T10
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: 382 / P21W
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10


EP3 Facelift

Headlights: H1 (Dipped), HB3 (Main)
Front Position Light: 501 / 194 / T10
Front Indicator: T20
Front Fog Lights: H11
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: W2 / 921 / 912 / T15
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10

Nice

Benny we need a Sticky with this type of info...

[JohnO]

You deserve a rep point there!

Sent from my HTC Incredible S using Tapatalk

[UNA91]

So apparently our seats have some sort of knee/leg extender? Is that so? :eek: cause that'll be nice haha. Anyone know how or where i can find how to adjust it? It's meant to be something like this...http://i178.photobucket.com/albums/w277/fukengrooven/Toy%20Civic%20Part%20Out/RecaroSeats02.jpghttp://i50.photobucket.com/albums/f302/skatejosh369/download-12.jpg

Also, I would like to replace my right side thigh bolster. Have looked though ebay and found a seller called 'capital.seating' selling bolsters for the ek9 and euro cl1 recaros, just wondering would they fit the ep3?

[RPS.13]

You just put your hand under there and pull it forward.

[wtfhax]

lift it up a bit first then pull forward

[[daan]]

Yes feel underneath the front of the seat, pull up and forward (as above) personally i just leave it alone its comfy already, but good to clean all the built up dirt that gathers in there

capital seating dont have bolster for the sportline series last time i checked. it would be worth sending them an email with a picture and confirm, though... i'm also not 100% if it can be changed like the SR3/SR4 as they are detachable bolsters. the EP3 Sportline i think is actually stitched to the main part of the seat (can someone confirm)

[UNA91]

Hmm, cause i thought the CL1 recaros were the same as the EP3, just difference colour and texture material...

[Perry]

Hmm, cause i thought the CL1 recaros were the same as the EP3, just difference colour and texture material...

You are correct on that.

[RPS.13]

Last time i looked at Capital Seating they had the bolster replacements, but that was early 2011 i looked. That was back when i needed a lever replacement. Got the part name from there and ordered the part from here: http://www.idealseat.com.au/

You can email on: idealseat@hotkey.net.au

Price wasl pretty similar to the UK.

[Lukezen27]

Last time I was IMG to pickup an 02 sensor the owner told me the EP3 he's currently got will more than likely be their last import for this model...

Good new for us in keeping their value I'd say

[stienerv2]

There was like 4 of them left on Monday.

[Philip Lee]

Last time I was IMG to pickup an 02 sensor the owner told me the EP3 he's currently got will more than likely be their last import for this model...

Good new for us in keeping their value I'd say

but IMG isn't the only importer......

however it's not cost effective to import as price is pretty cheap locally.

[JohnO]

You still got various importers down on parra road, I can see them start to import fd2r sooner or later in bigger quantities over the year or next.

Sent from my HTC Incredible S using Tapatalk

[Lukezen27]

but IMG isn't the only importer......

however it's not cost effective to import as price is pretty cheap locally.

Yeah that was the reason

[Perry]

Mugen RR time woohoooo

[bluey45]

You still got various importers down on parra road, I can see them start to import fd2r sooner or later in bigger quantities over the year or next.

Sent from my HTC Incredible S using Tapatalk

Awesome. I wouldn't mind a fd2r:)

[nny911]

Anyone here can confirm if the dc5r clutch and slave master cylinder is compatable with ep3r?

[UNA91]

^yes they are interchangable

[Serenity]

Actually Gavin at IMG told me Aussie import laws restrict the same basic chassis (shape and number of doors) from being imported into Australia. It's to protect the local market from imports of the same cars. But it also is the reason the JDM Integra Type R has never been imported (except for personal imports). So its probably going to be the same case with the FD2R, as it has the same shape and number of doors as the current standard model sedan civic (FD1).

[UNA91]

Anyone know where the dome light wire is? Im looking to install footwell leds to go with the dome lights and looking at the guides on google; they are all for the LHD EP3, so it's abit confusing to me. I am supposed to be looking for a Green/red wire like this: http://i81.photobucket.com/albums/j204/vegas10/ep3interiorlighting030.jpg

[bluey45]

Just wondering is the US Civic Si EP3 same as ours?

Cause I was trying to find some fogs for my Pre-FL EP3R and was wondering if these will fit??
http://www.ebay.com.au/itm/130572448398?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

[Symphorced]

On my phone so can't check out the link but USDM front bars are different to ours so it might not fit?

Sent from my GT-I9000 using Tapatalk

[keepitlow]

On my phone so can't check out the link but USDM front bars are different to ours so it might not fit?

Sent from my GT-I9000 using Tapatalk

+1 on that.. I read on another forum the bumper between USDM SI and JDM EP3R is different..

Would be better to spend a little more and buy OEM, fitting wise will be alot more easier.. less fiddling around :)

[bluey45]

Hmm. The Honda original parts got back to me and they said they don't have the fog brackets anymore. It's like discontinued. :(

[keepitlow]

Hmm. The Honda original parts got back to me and they said they don't have the fog brackets anymore. It's like discontinued. :(

I seeee : (

might be worth calling Hon Toy or Hon Bits to see if they have spares Kev...

[Perry]

+1 on that.. I read on another forum the bumper between USDM SI and JDM EP3R is different..

Would be better to spend a little more and buy OEM, fitting wise will be alot more easier.. less fiddling around :)

Indeed they are different and but to fit it u need to check the radiator.

[bluey45]

Hm. I will try Hon Toy or Hon Bits but not getting my hopes up.

If I cant get those fogs I was thinking might get some Philips 8 DRL's instead.

Also thinking of getting those FL projectors as well from the marketplace listed by Philip Lee here. Can I reuse my ballast and bulbs? or do I need to replace the whole thing?

Thanks

[keepitlow]

Hm. I will try Hon Toy or Hon Bits but not getting my hopes up.

If I cant get those fogs I was thinking might get some Philips 8 DRL's instead.

Also thinking of getting those FL projectors as well from the marketplace listed by Philip Lee here. Can I reuse my ballast and bulbs? or do I need to replace the whole thing?

Thanks

Hi Kev,

I posted this a while ago.. it seems the headlight bulb is different for Pre-FL and FL Head lamps, I would guess you need to replace the whole thing

EP3 Pre-Facelift

Headlights: H4 (Main and Dipped) Dual Filament
Front Position Light: 501 / 194 / T10
Front Indicator: Offset Pin BAU15S
Front Fog Lights: H11
Side Repeater: 501 / 194 / T10
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: 382 / P21W
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10


EP3 Facelift

Headlights: H1 (Dipped), HB3 (Main)
Front Position Light: 501 / 194 / T10
Front Indicator: T20
Front Fog Lights: H11
Interior Lights: 31mm Festoon 269
Interior Boot: 501 / 194 / T10
Rear Fog Light: 382 / P21W / BA15S (Single Filament)
Rear Indicators: Offset Pin BAU15S
Rear Reversing Lights: W2 / 921 / 912 / T15
Brake Lights: 380 / P21-5W (Dual Filament)
Centre Brake Light: 501 / 194 / T10
Rear Number Plate: 501 / 194 / T10

[bluey45]

Cheers Danny. I may have missed your post previously. Are your bulbs 8000K on your FL ep3?

[spookz]

My 03 EP3 seems to use T20 bulbs for the front indicators.

[keepitlow]

Cheers Danny. I may have missed your post previously. Are your bulbs 8000K on your FL ep3?

lol Kev.. I have no idea to be honest, I would say its close to 4000k as its factory spec! :)

8000k will become a bit purple in colour and less light on the road..

[keepitlow]

Here's a pic I took before when I changed some bulbs on my car for your reference in temperature colour.

Dip Bulb - Factory 4300k
High Bulb - 2500k
Fog Bulb - 2500k
Parkers - MTEC led 6000k

you can see the parker is slightly blue already than the pure white of main bulb..

http://i206.photobucket.com/albums/bb207/dannyhsu/DanEP3R.jpg

[damoqupak]

Hey Fellas,

I see you guys are talking about bulbs.. my front bulb is gone on my EP3.
I live near baulkham hills and need a bulb just stock or any suggestions for newer ones I'll buy a pair.
does anyone know where in sydney they sell them?

[Lukezen27]

Anyone 1/4 mile an EP3 with a K24?

[Perry]

Anyone 1/4 mile an EP3 with a K24?

I see your going down that route as well, buying Georges K24?

[Poeter]

Just bumped into this while I was searching for some light bulb size for EP3R



EP3 Facelift

Headlights: H1 (Dipped), HB3 (Main)


I'll be careful with this. I believe JDM facelift uses D2S bulb for their low beam hids. I think H1 are used by UKDM spec and also uses a different headlight housing even though both are projectors.

http://i1080.photobucket.com/albums/j321/spoonRR/EP3RFRHeadLight.jpg

Facelift Headlight Unit - No.1
HB3 Light Bulb - No. 7
D2S Type HID Light Bulb - No. 8
Factory HB3 Light Bulbs Holder - No. 10
Headlight Burner Cover - No. 12
Headlight Burner Seal - No. 14

See part number from this japanese epc website. http://honda.epc-data.com/civic/aba-ep3/702/electric/7586/

[Poeter]

Hm. I will try Hon Toy or Hon Bits but not getting my hopes up.

If I cant get those fogs I was thinking might get some Philips 8 DRL's instead.

Also thinking of getting those FL projectors as well from the marketplace listed by Philip Lee here. Can I reuse my ballast and bulbs? or do I need to replace the whole thing?

Thanks

No you can't reuse anything from your prefacelift. Different housing, different bulbs, and different wiring. Johno has done this before and wiring needs to be reconfiged.

If you're getting from Phillip, you must get the whole kit. It is completely useless to just buy the housing.

Another warning, do not buy projectors from hondaoriginalparts.com because their housing is only for UKDM which does not use HID. If you buy them you have to buy an aftermarket h1 hid kit to work with it. I have a friend who gone through this step.

So in conclusion you got three options:
1.) Buy the full headlight unit including ballast and bulbs from Phillip
2.) Buy brand new OEM projectors for UKDM spec and install aftermarket H1 HID kit
3.) Buy projector replicas from US and install aftermarket HID kit.

[Lukezen27]

I see your going down that route as well, buying Georges K24?

Maybe

Want’a SC but just not sure I can handle all the crap needs to my her legal like I did with my B16 Turbo..

If I do I’d go a K24 short block and my heat

Short blocks are only about a 1k

[Perry]

Maybe

Want’a SC but just not sure I can handle all the crap needs to my her legal like I did with my B16 Turbo..

If I do I’d go a K24 short block and my heat

Short blocks are only about a 1k

ARe you planniing on the rotrex non a/c setup???
Actually does George still have his?
Just go Turbo laaaa

[Lukezen27]

ARe you planniing on the rotrex non a/c setup???
Actually does George still have his?
Just go Turbo laaaa

Yeah George has the K24 for sale

If I go rotrex I'll be keeping the A/C

You make far more safe power with SC over turbo Perry

[bluey45]

No you can't reuse anything from your prefacelift. Different housing, different bulbs, and different wiring. Johno has done this before and wiring needs to be reconfiged.

If you're getting from Phillip, you must get the whole kit. It is completely useless to just buy the housing.

Another warning, do not buy projectors from hondaoriginalparts.com because their housing is only for UKDM which does not use HID. If you buy them you have to buy an aftermarket h1 hid kit to work with it. I have a friend who gone through this step.

So in conclusion you got three options:
1.) Buy the full headlight unit including ballast and bulbs from Phillip
2.) Buy brand new OEM projectors for UKDM spec and install aftermarket H1 HID kit
3.) Buy projector replicas from US and install aftermarket HID kit.

Cheers Peter, Danny and all other members. Thanks for your help. now just saving for them projectors :D

[Poeter]

EP3 Pre-Facelift

Headlights: H4 (Main and Dipped) Dual Filament



A fellow ep3 owner has asked me about the hid bulb for prefacelift and thought this might help some other ep3 owners.

H4's are halogens bulbs which are used by the UKDM spec.

The correct size is D2R for prefacelift and do not come cheap.

Please see the follwing diagram below:

http://i1080.photobucket.com/albums/j321/spoonRR/screen-capture-3.png


Part Number: 33116S0AJ11

For reference please see this link:
http://honda.epc-data.com/civic/la-ep3/10482/electric/7584/

[Perry]

Yeah George has the K24 for sale

If I go rotrex I'll be keeping the A/C

You make far more safe power with SC over turbo Perry

I dont know dude a little boost wont cause too much trouble =), I'm still worried about the rotrex kit with A/C the platum maifold design i mean. No intercooler needed strange.

[damoqupak]

A fellow ep3 owner has asked me about the hid bulb for prefacelift and thought this might help some other ep3 owners.

H4's are halogens bulbs which are used by the UKDM spec.

The correct size is D2R for prefacelift and do not come cheap.

Please see the follwing diagram below:

http://i1080.photobucket.com/albums/j321/spoonRR/screen-capture-3.png


Part Number: 33116S0AJ11

For reference please see this link:
http://honda.epc-data.com/civic/la-ep3/10482/electric/7584/

Nice Peter thanks for the help and I can't believe how expensive they are.

can we purchase after market ones then which should be cheaper?

[Poeter]

I think there are some D2R bulbs on ebay for around $70 a globe.

But I'll try to find out if there's any where else.

[damoqupak]

No you can't reuse anything from your prefacelift. Different housing, different bulbs, and different wiring. Johno has done this before and wiring needs to be reconfiged.

If you're getting from Phillip, you must get the whole kit. It is completely useless to just buy the housing.

Another warning, do not buy projectors from hondaoriginalparts.com because their housing is only for UKDM which does not use HID. If you buy them you have to buy an aftermarket h1 hid kit to work with it. I have a friend who gone through this step.

So in conclusion you got three options:
1.) Buy the full headlight unit including ballast and bulbs from Phillip
2.) Buy brand new OEM projectors for UKDM spec and install aftermarket H1 HID kit
3.) Buy projector replicas from US and install aftermarket HID kit.

Hey Peter you've exceeded your limit on PM messages so I couldn't reply.
thanks again mate and I think eBay is the way to go. Bluey45 ( Kevin ) has a spare OEM set which he's giving to me and I'll most def buy a spare set later on.

[Poeter]

No worries. PM have been cleared if you need anything else.

[Philip Lee]

So in conclusion you got three options:
1.) Buy the full headlight unit including ballast and bulbs from Phillip
2.) Buy brand new OEM projectors for UKDM spec and install aftermarket H1 HID kit
3.) Buy projector replicas from US and install aftermarket HID kit.

the problem with 1 is cost, the problem with 2 is there is no cut off which means will blind people, the problem with 3 is they are for LHD so they don't light up the curb side well + blind people.



No you can't reuse anything from your prefacelift. Different housing, different bulbs, and different wiring. Johno has done this before and wiring needs to be reconfiged.

the only wiring that needs to redo is for high beam. the oem pre FL plug to oem FL ballast is plug and play and parkers/indicators only need a small mod on the housing to fit. it's not that hard to rewire the high beam, any auto electrician can do it. this will need to be done regardless which of the 3 methods outlined by Peter.

[Lukezen27]

I dont know dude a little boost wont cause too much trouble =), I'm still worried about the rotrex kit with A/C the platum maifold design i mean. No intercooler needed strange.

na don't worrrie dude

I can show your how to SC with the rotrex including FMIC

Just need to find an elec a/c pump :)

Will look into it at the end of this year.. got some things I need to pay back first lol

[Perry]

na don't worrrie dude

I can show your how to SC with the rotrex including FMIC

Just need to find an elec a/c pump :)

Will look into it at the end of this year.. got some things I need to pay back first lol

Cool keep me in the loop I'm keen on the setup later on down track if i get bored the 2:L thing or if I keep my car.

[UNA91]

Is it possible to fit foglights with the mugen lip without having to cut my bumper up?

[cskfai]

Is it possible to fit foglights with the mugen lip without having to cut my bumper up?

You have a Pre-facelift EP or Facelift one?

For Pre-facelift, bumper cut is a must for installing the mugen lip. For Facelift, I have read a thread from ClubEP3. It doesn't need to cut bumper.

For foglight installation, here is a DIY thread.
http://www.k-series.com/tech_document.php?id=36

Or you may want the installation guide for reference
http://www.handa-accessories.com/civic/sifogs.pdf

[UNA91]

I have the prefacelift model and damn, not keen on cutting up any bodywork lol.. I.ve always thought the two holes in the mugen lip were for foglights =.= if only.. lol

[bluey45]

I have the prefacelift model and damn, not keen on cutting up any bodywork lol.. I.ve always thought the two holes in the mugen lip were for foglights =.= if only.. lol

Damn. That's what exactly I thought too. I was thinking of getting the mugen lip and getting fogs for my pre fl as well. :(

[damoqupak]

Damn. That's what exactly I thought too. I was thinking of getting the mugen lip and getting fogs for my pre fl as well. :(

well that bugs up my future plans too lol..

[cskfai]

Get air walker front lip then if you guys don't want to cut bumper
http://i187.photobucket.com/albums/x24/88crx2/dtp_ep3_06.jpg
http://i187.photobucket.com/albums/x24/88crx2/dtp08_18.jpg

[damoqupak]

Get air walker front lip then if you guys don't want to cut bumper
http://i187.photobucket.com/albums/x24/88crx2/dtp_ep3_06.jpg
http://i187.photobucket.com/albums/x24/88crx2/dtp08_18.jpg


that looks really good.

NICE.....

[Philip Lee]

Bluey, your PM is full!!

Thx

[UNA91]

Haha i'm sure somehow we can custom make a foglight housing to fit in the mugen lip holes, maybe iI should put some daytime running lights in those holes, but try to avoid the 'ricey' christmas lights look lol :\

[bluey45]

Bluey, your PM is full!!

Thx

Sorry Philip. I just cleared it! :p

[Philip Lee]

Sorry Philip. I just cleared it! :p

PM replied. Thx

[UNA91]

Anyone know the part number for spark plug seals? or do all K series engines use the same seal?

[Eskimo_firefighter]

Hey guys, didnt want to start a new thread about this, how thick are the JDM ep3r front and rear sway bars? From my research its 22mm rear and 19mm front? Can anyone confirm this for me?

[JDM EP3]

Anyone know if Mugen GP wheels fit on EP3?

[Eskimo_firefighter]

Its almost certain mugen gp wheels will fit an ep3. you really didnt give enough information on the specs of the wheel width, offset etc. But more than likely it will fit because mugen wheels and oem wheels have really high offsets and dont come that wide.

[JDM EP3]

I was thinking of running 17x8.5 with 48+

[TonyxTony]

Just bought a JDM EP3r yesterday, love it!

I notice the keys are so old style, is it possible to get it cut so that all the remote + key + immobilizer are together as one fat key?

My car didnt come with a log book, anyone know where I can find/download one?

What type of engine oil do you guys use?

Thanks
T

[Philip Lee]

Just bought a JDM EP3r yesterday, love it!

I notice the keys are so old style, is it possible to get it cut so that all the remote + key + immobilizer are together as one fat key?

My car didnt come with a log book, anyone know where I can find/download one?

What type of engine oil do you guys use?

Thanks
T

congrads.

with log book, do you mean service schedule and what's done at each service? most people would just follow DC5 schedules. if you are a baller, you can buy them from Honda Australia.

with engine oil, i used Castrol Edge 5w30. anything around that range eg. 0w40 etc will be fine.

thanks

[TonyxTony]

congrads.

with log book, do you mean service schedule and what's done at each service? most people would just follow DC5 schedules. if you are a baller, you can buy them from Honda Australia.

with engine oil, i used Castrol Edge 5w30. anything around that range eg. 0w40 etc will be fine.

thanks

THANKS!!! yep I was trying to get a hold of the service schedule. So the DC5R is similar to the EP3R? Thanks!

Do we service every 5000kms?

[Philip Lee]

THANKS!!! yep I was trying to get a hold of the service schedule. So the DC5R is similar to the EP3R? Thanks!

Do we service every 5000kms?

Engine oil and oil filter a good idea, everything else depends. Honda Aus service interval is usually 6mths/10,000km.

[bluey45]

Does anyone know how to change the shifter knob in the EP3? :confused:

[Symphorced]

Twist counter clockwise?

Sent from my GT-I9000 using Tapatalk

[RPS.13]

Or undo the locking nut, then twist.

[Philip Lee]

Or undo the locking nut, then twist.

this.

personally i think the best gear knob is the OEM one. i have tried ARC titanium round ones, Razoo long ones and Skunk 2 heavy ones.

i just screw the OEM down all the way without the nut. although the pattern is not right but this feels the best for me.

[bluey45]

Or undo the locking nut, then twist.

So the locking nut under the actual knob? just a spanner will be fine? sorry sound so noob, first time doing it

[[daan]]

Yes mate should be able to loosen it by hand but if not, use a tool.

Has anyone tried an fn2r round knob or the mugen knob on their ep3? I kind of want to change mine just cos, but if the oem one is best I might not bother...

[RPS.13]

I`ve seen a few members on here running the round knobs.

I'm using a nismo gt duracon knob and I love it. Perfectly weighted, great shape and doesn`t get hot or cold.

[bluey45]

;3228202']Yes mate should be able to loosen it by hand but if not, use a tool.

Has anyone tried an fn2r round knob or the mugen knob on their ep3? I kind of want to change mine just cos, but if the oem one is best I might not bother...

I got the mugen round knob, but have to get the OEM one off first.

[Perry]

;3228202']Yes mate should be able to loosen it by hand but if not, use a tool.

Has anyone tried an fn2r round knob or the mugen knob on their ep3? I kind of want to change mine just cos, but if the oem one is best I might not bother...

I'm running a ARC round knob best little mod for shifting.

[JohnO]

The spoon plastic knob was fun to shift and wasn't even a kg like the metal knobs!

fapatalk

[Symphorced]

I have the OEM round fd2r/fn2r (same?) one. Like the feel of it and imo looks better than the egg shape.

Sent from my GT-I9000 using Tapatalk

[JohnO]

Pm me if you want the fn2 knob I got one laying around in my room. Also spoon knob too

fapatalk

[Poeter]

I personally like the OEM egg shape. It's original and ergonomic.

[[daan]]

good responses thanks guys. i might give the round knob a try

[alanalan]

price & condition of fn2r knob?

[Philip Lee]

I personally like the OEM egg shape. It's original and ergonomic.

i agree. the location of the shifter means you hold the gear knob from the side rather than from the top. therefore i feel a longer gear knob makes it easier to shift.

a round one is best if the shifter is low and you hold the gear knob from the top.

[frambo]

i agree. the location of the shifter means you hold the gear knob from the side rather than from the top. therefore i feel a longer gear knob makes it easier to shift.

a round one is best if the shifter is low and you hold the gear knob from the top.


Spot on Phillip
Only problem is once the sun smashes it its too hot to handle -.-"

[stienerv2]

Spot on Phillip
Only problem is once the sun smashes it its too hot to handle -.-"

Get your mum to make you a beanie like i did. Works alrite

[frambo]

my brother got a sweat band with his air maxs ive just been using that, still not in the habbit of it and forget and when i do ouch i pay the price

[TonyxTony]

is it normal to have some oil mark on the top of the engine? im not sure if it was there because of over spill or coming out abit :/
http://farm8.staticflickr.com/7150/6811522801_42dc3d77fe_z.jpg (http://www.flickr.com/photos/tonysflickr/6811522801/)

http://farm8.staticflickr.com/7022/6811521007_1689003b17_z.jpg (http://www.flickr.com/photos/tonysflickr/6811521007/)

http://farm8.staticflickr.com/7002/6811519369_425e6438c3_z.jpg (http://www.flickr.com/photos/tonysflickr/6811519369/)

http://farm8.staticflickr.com/7154/6811517713_d2409cc060_z.jpg (http://www.flickr.com/photos/tonysflickr/6811517713/)

[Lukezen27]

is it normal to have some oil mark on the top of the engine? im not sure if it was there because of over spill or coming out abit :/








Mine comes out a bit think

Think its normal but someone might enlighten us?

Remember one small drop spreads like you would not beleave

[Perry]

Headgasket?

[bluey45]

Hey guys, I just replaced my gear knob with the mugen one. Just wondering how you got it level? As when I screw it all the way down the gear markings are sideways? Did you have to put in a washer or nut?

[Symphorced]

Hey guys, I just replaced my gear knob with the mugen one. Just wondering how you got it level? As when I screw it all the way down the gear markings are sideways? Did you have to put in a washer or nut?

Did you retain the locknut? Have that underneath the gearknob so that you can get the markings level.

[bluey45]

Did you retain the locknut? Have that underneath the gearknob so that you can get the markings level.

I don't have a locknut. Mine didn't come with it.

[will13]

any nut of that thread size will do. just get the knob on to where it needs to be then wind a nut up to hold it there

[bluey45]

any nut of that thread size will do. just get the knob on to where it needs to be then wind a nut up to hold it there

Cheers will. I'll hit up bunnings

[Philip Lee]

U didn't have a nut with the stock gear knob? Weird!!

[bluey45]

U didn't have a nut with the stock gear knob? Weird!!

Yeah unfortunately. Any where I can get my hands on that gear lock nut?

[Philip Lee]

Which mugen u have? The round one or the one with a flat top?

If its the latter, u don't need any more nuts. The package has everything u need.

[bluey45]

Which mugen u have? The round one or the one with a flat top?

If its the latter, u don't need any more nuts. The package has everything u need.
got the round one

[bluey45]

Hey guys, I got my mugen round knob installed today. For anyone if you don't have a locknut then you need to get a 10mm fastener from bunnings instead, it does the same job. Here are some pics.

http://img.tapatalk.com/6eae82de-c6f2-f36d.jpg
http://img.tapatalk.com/6eae82de-c709-3e28.jpg

[stienerv2]

Looking nice man, i never knew you had the leather shift boot

[bluey45]

Looking nice man, i never knew you had the leather shift boot

Cheers man. The knob is awesome, much better than the OEM one.:D

[alanalan]

looks sleek yo

[keepitlow]

Looks great Kev :)

didn't know you had th leather shift boot as well.. I'm thinking about getting Blox Neo Chrome shift knob although its like 490g..

would you know how heavy is the Mugen knob?

[keepitlow]

btw can anyone confirm if this true.. I read somewhere online saying due to the shift position of the EP3R heavy gear knobs may cause it to pop out of 3rd gear under hard acceleration..

hence why I've being holding back and staying with the stock gear knob..

[Lukezen27]

btw can anyone confirm if this true.. I read somewhere online saying due to the shift position of the EP3R heavy gear knobs may cause it to pop out of 3rd gear under hard acceleration..

hence why I've being holding back and staying with the stock gear knob..

Sounds like a load of crap if ya ask me

[keepitlow]

^^ lol yahh... but it got me thinking a bit :) hahahaa

[UNA91]

^ I too have heard such theories when I was considering buying a skunk2 gear knob. There's quite a debate on whether weighted gear knobs will damage our synchros too..

[Perry]

Where are u guys getting these info from and what is considered as heavy?

[bluey45]

Looks great Kev :)

didn't know you had th leather shift boot as well.. I'm thinking about getting Blox Neo Chrome shift knob although its like 490g..

would you know how heavy is the Mugen knob?

Thanks Danny. I think the mugen round knob weighs about 180g?

[Poeter]

Headgasket?

Actually, it's rocker cover gasket.

Best to get this replaced while you also do valve clearance. It's not an expensive job.

Mine has a bit of oil seepage too but not as severe.

[keepitlow]

Where are u guys getting these info from and what is considered as heavy?

lol I think anything above 400g is quite heavy..


Thanks Danny. I think the mugen round knob weighs about 180g?

pretty good mate :) looks good as well!

[Perry]

lol I think anything above 400g is quite heavy..



pretty good mate :) looks good as well!


I just want to know where are people getting these info from thats all.

[keepitlow]

I just want to know where are people getting these info from thats all.

Perry google :)

its a bit of a debate.. 50 50 if you ask me!