EP3 Type R

[geeang]

pics on your EP3 geeang =) I assume the cable guide will only snap when your changing the bushings yeah?

Yep exactly, had to replace the entire shifter cables because of that stupid mistake lol

Just one pic for now:
http://img.photobucket.com/albums/v352/viet_mafia/DSC_0076_zpsd86a778b.jpg

[Symphorced]

@geeang: what tyre and wheel specs?

@brody: you should have a USB connection coming out from the ECU to plug into your laptop.

[doosra]

yea i thought it was abit low, idk if its because they had modified the test pipe section since they said it was about 2 inches longer and didn't bolt up to the mid pipe. My resonator also looks lower than usual, about the same height as the mid pipe, but it has no scrape marks so it must've sat higher before since my mid pipe has always been all scraped up. One thing about this headers is that it doesn't have hangers like the oem one did near the cat. Maybe i can get the hangers where it connects the axle back shortened, would that help? I put a jack under the exhaust and it seems that it can be made to sit a little higher.

You can see theres abit of room between the heatshield and the pipe
http://imageshack.us/a/img441/6910/imag0921.jpg
'

they modified my test pipe as well. I saw them chop some of it off

[brody]

@geeang: what tyre and wheel specs?

@brody: you should have a USB connection coming out from the ECU to plug into your laptop.

Yeh got it haha. Saw the connection but thought they might've forgotten to give me the cable. Turns out I can just use my printer USB cable. Cheers

[geeang]

@geeang: what tyre and wheel specs?

RPF1 - 17x9 +35
RE002 - 225/45/17
Rear needs to be lowered (which is obvious) but I've been far too lazy to get around to it.

[Symphorced]

Rear will most likely scrub if you lower it more. I run for track x8.5 +30 with 225/45 on the rears with -2 degree camber and I scrub. Your set up will sit out a touch more too.

[stienerv2]

I've got neomax silver's from shift performance. bumpy ride but cheap at $1300.

How did you end up fitting the neos? The strut bolts are not 16mm but are 14mm?

[stienerv2]

Rear will most likely scrub if you lower it more. I run for track x8.5 +30 with 225/45 on the rears with -2 degree camber and I scrub. Your set up will sit out a touch more too.

You could roll you guards and trim the plastic on the bumper so you won't scrub. I ran some aggressive offset with barely any negative camber and got away with it.

[doosra]

How did you end up fitting the neos? The strut bolts are not 16mm but are 14mm?

i took it to a workshop to put it in and they had no problems with it

[Symphorced]

You could roll you guards and trim the plastic on the bumper so you won't scrub. I ran some aggressive offset with barely any negative camber and got away with it.

Rolled all four corners already. Might just be the chunky sidewalls of the Hankook RS3s...

[RPS.13]

I snapped my cable guide a while back when installing some billet bushings too, hybrid racing only very recently started making billet shifter cables for the EP3, and as far as I know is currently the only solution for EP3's at the moment.

Would really like to see what your impressions are if you decide to get them :D

Thanks for the info geeang :thumbsup:

I did a quick search during work, apparently corsport makes them too. But i`ll most likely bite the bullet and get the hybrid racing ones.

Will do man, i`ll post up some feedback once i get them. Just waiting on confirmation from hybrid racing to see if they'll fit.

I highly doubt the glue trick will hold up for much longer, i think it snapped in a different spot too. I was only shifting normally into 1st when it broke.

[butterfingers]

RPF1 - 17x9 +35
RE002 - 225/45/17
Rear needs to be lowered (which is obvious) but I've been far too lazy to get around to it.

How much clearance do you have with the trailing arm?

[Lukezen27]

I'm running 18x8.5" with rolled guards using rear camber bolts and only one side rubs :(

[butterfingers]

theres no such thing as rear camber bolts...

[Lukezen27]

theres no such thing as rear camber bolts...

Yes there is

I think

[butterfingers]

you mean camber arms.

[Lukezen27]

you mean camber arms.

hm

George handed my two OEM bolts and said he'd installed camber bolts on the rear!

We have a look tonight :)

[Perry]

hm

George handed my two OEM bolts and said he'd installed camber bolts on the rear!

We have a look tonight :)

His chop it hahahah where is that George lately?

[Lukezen27]

His chop it hahahah where is that George lately?

Gone-ski

Won't answer my calls :(

Just lives round the corrner

Might be dead

[Symphorced]

You sure they weren't for the front Luke?

[Lukezen27]

You sure they weren't for the front Luke?

From memory no backs but yeah ya never know

[lemmiwinks]

Anyone got an alarm wiring diagram? Just trying to fit an alarm to my 02 ep3 and the colours are completely different to USDM wiring.

[geeang]

How much clearance do you have with the trailing arm?

I'm not 100% sure but I've never had any problems with rubbing on the trailing arms, and I'm only running -0.5 degrees of camber on the rear too.
I'll be running -1.5 or -2 degrees when I drop it some more, which should give me even more trailing arm clearance.

[Perry]

I'm not 100% sure but I've never had any problems with rubbing on the trailing arms, and I'm only running -0.5 degrees of camber on the rear too.
I'll be running -1.5 or -2 degrees when I drop it some more, which should give me even more trailing arm clearance.

When you have spare time could you send a pic to be from the wheel to see the clearance plz? you can PM me if you want cheers.

[UNA91]

I have a moth stuck in my headlight... I hope it doesn't die in there lol

Anyway, has anyone tried 'seafoam' on their cars? Apparently the australian alternative for it is "subaru upper engine cleaner" from subaru or 'nulon foaming intake cleaner'. Both work the same to clean out the carbon, applied the same and does the smoke show and all...

[kenny07]

hey guys....

my battery in my ep3 died out today..

well im pretty sure its my battery because car wont start, lights wont turn on and so on and etc etc..

was wondering if i got a new battery...

do i need to get a specific type of battery or can i just rock up to any supercheap auto and get any type of car battery?

[UNA91]

You need to look at the cold cranking amps or cca, all batteries will state it and the higher the better, but usually that means the battery will be bigger and might not fit in the battery compartment. I think the oem battery for the ep3 is 360 cca so anything above is fine just make sure it will fit in the battery compartment. I went for the highest cca that could still fit cause it had a longer warranty, and cranks better too :)

[kenny07]

You need to look at the cold cranking amps or cca, all batteries will state it and the higher the better, but usually that means the battery will be bigger and might not fit in the battery compartment. I think the oem battery for the ep3 is 360 cca so anything above is fine just make sure it will fit in the battery compartment. I went for the highest cca that could still fit cause it had a longer warranty, and cranks better too :)

ok so just ask for a battery with 360 cca or higher and it should be ok?

[UNA91]

yea just note the size of the battery and it should be good

[stienerv2]

And the way the terminal sits on the battery. So the 3 main things are:

1. Shape and size.
2. CCA.
3. Terminals

[kenny07]

And the way the terminal sits on the battery. So the 3 main things are:

1. Shape and size.
2. CCA.
3. Terminals

thanks guys... as you can see im pretty noob! lol
all the info above should be noted on the battery yeah?

i havent popped open my hood yet to check.. gonna do it tomorrow as shops arent open today..

and HO HO HO! Merry Christmas everyone!! :D

[doosra]

anyone tried valvoline synpower 5w-40, fully synthetic. they're on special at supercheapauto $50 down from $65. I just bought 20L worth.

[UNA91]

What radiator fluid concentration should i be using? Looking to do a flush sometime. I know I should be using the green coolant but there are some that are more concentrated than others like 33% or 50% anti freeze/boil and stuff.

[uniqlo]

Have you tried PR [Perfect Run]? RHDJapan is the most expensive, even more expensive than Greenline!

IIRC, they have to ship it to them in Europe, then ship to you in Australia...

I got a quote from these guys too. They are slightly cheaper.
They can get it to your door for the same price that JDM concept sells without postage.
It still works out to be like $225ish.
Possibly can get it cheaper from them if you buy more than one set?

[lemmiwinks]

Can someone tell me where the temperature gauge needle sits when the thermostat kicks in? Is it half way?

[UNA91]

Mine sits a little under half way which i thought was a problem but apparently all ep3rs sit like that. Tho idk why my aftermarket temp gauge sits at 70-75c but when idling at the lights or along traffic it sits around 85-90c, must be the radiator getting more air. Thermostat begins opening at 80c and is fully open at 90c according to the manual.

[RPS.13]

Anyone know of a diy link to remove/install shifter cables?

Or to anyone that has diy`ed it, on a scale of 1 to 10. How hard were they to install?

Thanks in advance.

[geeang]

Anyone know of a diy link to remove/install shifter cables?

Or to anyone that has diy`ed it, on a scale of 1 to 10. How hard were they to install?

Thanks in advance.

It's not a hard thing to do, it's just a huge pain in the ass because the exhaust is in the way, and because it's such a tight fight inside the centre console.

3/10 for difficulty, 9/10 for being a pain in the ass.

[dc2screama]

Whose is everyone insured with?
Recommend anyone..
Cheers

[-JC-]

Whose is everyone insured with?
Recommend anyone..
Cheers

Shannon's, bout $55 a month.

[dc2screama]

Any p platers?

[RPS.13]

It's not a hard thing to do, it's just a huge pain in the ass because the exhaust is in the way, and because it's such a tight fight inside the centre console.

3/10 for difficulty, 9/10 for being a pain in the ass.

Cheers man! Ahh, that's sounds annoying. Probably the one thing I hate most about the ep is the lack of space to work on stuff. Good to know its not too hard though.


Whose is everyone insured with?
Recommend anyone..
Cheers

Shannons, $473.53 half yearly. Including a 10% discount for holding a cams licence.

[UNA91]

has anyones handbrake button chrome chipped off? been meaning to take care of it but dunno if any paint will hold up to the constant use lol

[UNA91]

Anyone know the part number for this stud? mine snapped

http://imageshack.us/a/img441/6779/imag0951d.jpg

edit: dw found it: BOLT A, HEAD COVER, 90011-PNA-003.

[dnapol]

has anyones handbrake button chrome chipped off? been meaning to take care of it but dunno if any paint will hold up to the constant use lol

Yeh I bought mine with all that plastic chrome chipped off, looks weird. Was thinking about replacing it with a drift button (for gags)

[RPS.13]

Any of you guys running aircon delete kits on your ep's?

I'm considering deleting my ac, rather than regassing it.

Wondering if it gains any power without the ac, or is it just to save weight?

[UNA91]

I think it's mostly weight savings. The only power gained is by not using the aircon lol I've only ever used my aircon once since owning the car, that was when i had my windows tinted and couldn't use them for a day, tho handy to have on a rainy day when the condensation buildup is bad.

[geeang]

Does anyone know where I can find a front passenger side fender lining? Need to replace mine but for the life of me, I can't find one anywhere!

[UNA91]

clutch slave cylinder is so squeaky... took it apart to grease it up, also greased the release fork and it still squeaks...

[RPS.13]

I think it's mostly weight savings. The only power gained is by not using the aircon lol I've only ever used my aircon once since owning the car, that was when i had my windows tinted and couldn't use them for a day, tho handy to have on a rainy day when the condensation buildup is bad.

Cheers for the info UNA91.

[brody]

Doing a full service this week(gearbox/engine oil, clutch/brake fluid, sparkplugs).. just rounding up all the oils. Cars got just under 100k on it. Recommend 5w 40 or 10w 40 engine oil?

[brody]

Ah also, anyone know if AUD and JDM timing chain and tensioner are the same?

[UNA91]

Anyone else find the plastic interior is soft and incredibly easy to scratch?

[doosra]

Anyone else find the plastic interior is soft and incredibly easy to scratch?

Yeap, very easy, mine is scuffed a bit. I assume there's some plastic cleaning product we could use to shine and smooth it out?

[doosra]

Doing a full service this week(gearbox/engine oil, clutch/brake fluid, sparkplugs).. just rounding up all the oils. Cars got just under 100k on it. Recommend 5w 40 or 10w 40 engine oil?

you could use either of them.

[UNA91]

Yeap, very easy, mine is scuffed a bit. I assume there's some plastic cleaning product we could use to shine and smooth it out?

theres a product called meguires plastic x but idk how well it'll do on the bumpy textured surface. my glove box has a few scratches on it as well as the driver side pillar from installing gauges, heat gun and rubbing method worked abit

[doosra]

I might head to supercheapauto and try the meguire quik interior detailer and see how it goes

[doosra]

need help. all of a sudden my power steering stopped working and then realised my digital dash stopped working. I turned the car off and back on and no warning lights light up on the dash as well. I checked my alternator fuse and it's fine.

[geeang]

Did you check all of your other fuses at the same time?
Make sure you check all fuses under the hood as well as under the dash, my digital dash fuse has blown twice before.

[doosra]

I'll check again tomorrow. my dash actually lights up but the digital odometer doesn't work, fuel tank goes to empty and no warning lights flick on when I key in the ignition. weird.

[UNA91]

anyone here have the omni power clutch master cylinder? apparently it completely changes the way the clutch pedal position and feel in a way that its alot closer to the firewall and is very stiff?

[doosra]

Did you check all of your other fuses at the same time?
Make sure you check all fuses under the hood as well as under the dash, my digital dash fuse has blown twice before.


problem solved. was 7.5a fuse

[CrazyPotato]

Anyone know where to get new ep3 fl headlights?

[doosra]

Anyone know where to get new ep3 fl headlights?

You can get them off an ebay seller in the UK. The eBay seller mentioned that they will fit

"however pre-face EP3's will need modification to the bulb wiring successfully fit the headlights.

The information needed to do the modification has been listed by a help user on the forum below:-

http://www.civictype-r.co.uk/index.php/how-to-guides/46-ep3-how-to-guides/72-fitting-facelift-headlights-to-a-prefacelift-car"

http://www.ebay.com.au/itm/200834520423?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

If you do decide to buy them, I suggest you contact them directly and purchase it outside of eBay to avoid VAT tax that only people in the UK have to pay. I've been quoted 225 pounds + 80 pounds postage which is about $470 AUD delivered which is a good price.

Please let me know how you go if you decide to get them as I'm potentially interested in future.

They are also projector lights, not HID.

[CrazyPotato]

You can get them off an ebay seller in the UK. The eBay seller mentioned that they will fit

"however pre-face EP3's will need modification to the bulb wiring successfully fit the headlights.

The information needed to do the modification has been listed by a help user on the forum below:-

http://www.civictype-r.co.uk/index.php/how-to-guides/46-ep3-how-to-guides/72-fitting-facelift-headlights-to-a-prefacelift-car"

http://www.ebay.com.au/itm/200834520423?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

If you do decide to buy them, I suggest you contact them directly and purchase it outside of eBay to avoid VAT tax that only people in the UK have to pay. I've been quoted 225 pounds + 80 pounds postage which is about $470 AUD delivered which is a good price.

Please let me know how you go if you decide to get them as I'm potentially interested in future.

They are also projector lights, not HID.

Thanks for the info mate, seems like a lot of work to do the conversion though but I'm considering doing it once my EP arrives or when I'm more mechanically experienced as this would be my first car and mod. Would I need to get a HID kit if I want to go HIDs? The guy mentions HID ballasts but never mention the part number or anything so I assume its in the kit?

[doosra]

I'm not too sure. I'd suggest just installing headlights first and see how it looks at night and if need be then get a hid kit which is easy to install. you may be happy with the projectors

[Lukezen27]

Thanks for the info mate, seems like a lot of work to do the conversion though but I'm considering doing it once my EP arrives or when I'm more mechanically experienced as this would be my first car and mod. Would I need to get a HID kit if I want to go HIDs? The guy mentions HID ballasts but never mention the part number or anything so I assume its in the kit?

Could be lucky like me and still have ths stock HIDs in :)

[-JC-]

Could be lucky like me and still have ths stock HIDs in :)

Same here, just talk to your importer before they start pulling all of the good gear out of it!

[Icebox]

Anyone know of a good smash repair in sydney, that knows what an Ep3 R is? and are able to source a bumper and fenders if i may get into an accident, as my usual smash repairer "Exclusive Body Works" only specialise in nissan, Lexus and the other high class brands and cant seem to find a decent smash repairer who doesnt cut cost, these days

[geeang]

Anyone know of a good smash repair in sydney, that knows what an Ep3 R is? and are able to source a bumper and fenders if i may get into an accident, as my usual smash repairer "Exclusive Body Works" only specialise in nissan, Lexus and the other high class brands and cant seem to find a decent smash repairer who doesnt cut cost, these days

Status Paint and Panel - 9729 0800
26B Davis Road
Wetherill Park
They sourced me a facelfit front bumper + front lip + front guard + facelift headlights, painted all of it perfectly and fitted it all within 1 week.

[Icebox]

Status Paint and Panel - 9729 0800
26B Davis Road
Wetherill Park
They sourced me a facelfit front bumper + front lip + front guard + facelift headlights, painted all of it perfectly and fitted it all within 1 week.

Wow, how long ago was this?

[geeang]

Wow, how long ago was this?

2 weeks ago lol

[doosra]

How much was it to source and install the fl headlights?

[geeang]

How much was it to source and install the fl headlights?

My car is a standard facelift (small repairs through insurance).

[Icebox]

2 weeks ago lol

lol cool! thanks for the help, gonna contact them on monday and see what they can do,

[UNA91]

Anyone know if the front control arm bushings for a RSX will fit the EP3? Looking at upgrading to energy suspension since i found a tiny hairline crack in mine

http://www.kseriesparts.com/merchant.mvc?Screen=PROD&Store_Code=CR&Product_Code=ENS-16-3116G

[butterfingers]

Anyone know if the front control arm bushings for a RSX will fit the EP3? Looking at upgrading to energy suspension since i found a tiny hairline crack in mine

http://www.kseriesparts.com/merchant.mvc?Screen=PROD&Store_Code=CR&Product_Cod e=ENS-16-3116G

Identical afaik

[geeang]

You can get them off an ebay seller in the UK. The eBay seller mentioned that they will fit

"however pre-face EP3's will need modification to the bulb wiring successfully fit the headlights.

The information needed to do the modification has been listed by a help user on the forum below:-

http://www.civictype-r.co.uk/index.php/how-to-guides/46-ep3-how-to-guides/72-fitting-facelift-headlights-to-a-prefacelift-car"

http://www.ebay.com.au/itm/200834520423?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

If you do decide to buy them, I suggest you contact them directly and purchase it outside of eBay to avoid VAT tax that only people in the UK have to pay. I've been quoted 225 pounds + 80 pounds postage which is about $470 AUD delivered which is a good price.

Please let me know how you go if you decide to get them as I'm potentially interested in future.

They are also projector lights, not HID.

I just bought a driver's side facelift headlight from these guys, OEM part in Honda Japan box, arrived in 4 days (including the weekend).

[doosra]

How much did it cost you and is it genuine oem and did you fit it yet? any issues?

[geeang]

How much did it cost you and is it genuine oem and did you fit it yet? any issues?

Cost me around $250 shipped, Genuine OEM in Honda Japan box.

Not fitted yet, but it'll be straight plug and play for me because my car's a facelift anyway.

[UNA91]

I'm thinking of upgrading my hasport mounts with their 70a inserts, would it be a huge difference over 62a in terms of vibes? I'm currently running 62a with 70a in the rear.

Ever since i got the 62a I feel like it could be abit stiffer and keep thinking if i should have gone 70a cause i can feel the engine jerk slightly at high rpms and letting off/shifting. The vibes aren't even that bad with 62a after they break in and honestly I can't feel any difference in vibration compared to stock mounts apart from turning the car on and at high rpms, but thats probs cause i had been driving with a busted oem drivers side mount for quite awhile before so I kind of got used to it.

[UNA91]

Anyone know the correct NGK spark plug for our engine? So far i've found one person using ZFR6FIX11 which has a .044 gap but then there is also IFR7G-11KS laser iridium which has the same .044 gap but is a colder spark? :S

[Brando0np]

Anyone selling OEM EP3 Suspension (Rears) ?

[doosra]

Anyone selling OEM EP3 Suspension (Rears) ?

If the price is right I may

[Brando0np]

Check PM !

[PHO]

Anyone selling OEM EP3 Suspension (Rears) ?

Pm mocchi. He's wrecking an ep3r. Dunno if rears are gone yet.

[Lukezen27]

Hi Guys

I know its been covered before but where can I buy some replacement tie rod ends?

Maybe TODA

[Symphorced]

Hi Guys

I know its been covered before but where can I buy some replacement tie rod ends?

Maybe TODA

Check Mike's (rps13) build thread. I recall he had the exact measurements and the website to order them from.

[Perry]

Hi Guys

I know its been covered before but where can I buy some replacement tie rod ends?

Maybe TODA
Luke there is a shop which sells them at the northern beaches.

[Lukezen27]

Luke there is a shop which sells them at the northern beaches.

Oh hook me up Perry

Needed a bit of local knowledge :)

[SuperSteve]

Hehe u guys so cute !

[Perry]

suppp Steve!!!!

[SuperSteve]

sup brother pezza :D

not much

my car finally getting a wash with all this rain lol

[Perry]

sup brother pezza :D

not much

my car finally getting a wash with all this rain lol

LOL yeah mine had a wash this afternoon so when are all old guys meeting up again?

Back to work tmorrow =(

[Lukezen27]

Luke there is a shop which sells them at the northern beaches.

Stop holding out on me Perry :(

[butterfingers]

Sydney guys: where do you go for your wheel alignment and fitment needs?

Thanks in advance

[Perry]

Stop holding out on me Perry :(

I need to dig around for the receipt Luke try to find it tonight for you.

[cvc88]

My seat belts for my ep3 is starting to play up and doesnt retract properly. Does anyone know where I might be able to find a replacement and how much they usually go for? I'm after both the driver and passenger side if they are different.

Thanks!

[stienerv2]

sup brother pezza :D

not much

my car finally getting a wash with all this rain lol

I saw your wheels last week. The spokes seem whiter but the inner parts are still black lol.

So when is the next meet up?

[RPS.13]

Anyone know where to buy extended wheel studs for the ep3?

[LD_Mart]

Anyone know where to buy extended wheel studs for the ep3?

Just go to repco, cant remember how much they are but they were pretty cheap

[UNA91]

Just changed my spark plugs, then something occurred to me. Does it matter what cylinder the spark plug harnesses go in (the part that goes down the spark plug hole)? They all look the same and have no indication at all...

[butterfingers]

I believe they have a firing order from 1-4 so it does matter. Take this with a grain of salt this was just wat I heard

[chargeR]

Just changed my spark plugs, then something occurred to me. Does it matter what cylinder the spark plug harnesses go in (the part that goes down the spark plug hole)? They all look the same and have no indication at all...

You're talking about the coils correct? They look like this:

http://oi55.tinypic.com/339q89h.jpg

They are all the same, it doesn't matter which goes where.

[UNA91]

You're talking about the coils correct? They look like this:


They are all the same, it doesn't matter which goes where.


Yes thats it lol, sweet thanks for clearing it up!

[Icebox]

Anyone know where to buy extended wheel studs for the ep3?

hey mike i got my wheel studs for from the 2 sites below:

http://www.summitracing.com/parts/arp-100-7715

http://jdmaccessories.bigcartel.com/product/blackworks-extended-wheel-studs

arp studs are better quality but then again same thing

[dnapol]

Snapped a stud holding my cam cover on. Shit balls!

[Lukezen27]

Anyone feel like hit'n 1/4 Mile soon?

[SuperSteve]

Wouldnt mind dude. All depends with work though

[Perry]

supp Steve!!!

[Lukezen27]

Wouldnt mind dude. All depends with work though

Thats my problem also Steve

[viett]

Anyone know any black ep3r owners whom are thinking of selling? :D Looking to join the ep3 chat!

[Lukezen27]

Anyone know any black ep3r owners whom are thinking of selling? :D Looking to join the ep3 chat!

Good luck with that lol

Once you give-up

http://www.ozhonda.com/forum/showthread.php?161840-CW-2002-Honda-Civic-TYPE-R-(EP3R)-Haltech-ECU-Injen-CAI-Kidracer-Header-136kw-ATW

[doosra]

Anyone know any black ep3r owners whom are thinking of selling? :D Looking to join the ep3 chat!

Check Carsales. I did drive past one yesterday with a Carsales for sale sticker on it which was black

[bluey45]

Anyone know any black ep3r owners whom are thinking of selling? :D Looking to join the ep3 chat!

Well if you give up on the black one, I'm also selling mine as well lol.

http://forum.clubitr.com.au/showthread.php?t=12859

http://carsales.mobi/cars/details/?R=14120128

[bennjamin]

if anyone wants some front swaybar endlinks - got some here. Take them for free.
Aftermarket but same stuff. Brand new la !

[SuperSteve]

supp Steve!!!

ello pezza ! u can come 1/4 mile with me and luke yeah :D ok done ! book it in boys !

[Lukezen27]

if anyone wants some front swaybar endlinks - got some here. Take them for free.
Aftermarket but same stuff. Brand new la !

Benny needs to come to Steve :)

You can bring your little GTI

[bennjamin]

Benny needs to come to Steve :)

You can bring your little GTI

to Steve ?

I don't want to run 14's all day long in front of you ep3 kids lol

[SuperSteve]

Haha aslong as his not coming on me I'm fine with that. Bring the gti golf benny boiiiiiii

[Lukezen27]

Haha aslong as his not coming on me I'm fine with that. Bring the gti golf benny boiiiiiii

you liked it last night!

[SuperSteve]

Hahahaha

[Lukezen27]

Hahahaha

helmet I'm looking to get
https://www.thehelmetwarehouse.com.au/store.php?crn=226&rn=4115&action=show_detail

Same as my last one but while :)

[SuperSteve]

Nice

How come u need new helmet ?

[Lukezen27]

Nice

How come u need new helmet ?

old ones not allow at the Creek

new specs are in

[SuperSteve]

Oh. What are new specs ? One I've always used is a motor bike helmet full cover

[Lukezen27]

Oh. What are new specs ? One I've always used is a motor bike helmet full cover

needs that anell 2005 or somethiong like that

the the the Creek web site

My other ones was close to brand new but still not good enough :(

[viett]

How does the Mugen intake compare to the Grupe M?

[Symphorced]

How does the Mugen intake compare to the Grupe M?

On a scale of 1 (being the worst intake ever) and 1,000,000 (being the ultimate intake), I would rate it 738,543 out of 1,000,000.

[dnapol]

Just go gruppem and never look back! one of my better mods!

[viett]

How much is a used Gruppe M roughly cost?

[bluey45]

How much is a used Gruppe M roughly cost?

Should be about $700 to $800

[dnapol]

Go to perfect run Japan now! Should pick it up very cheap new!

[Eskimo_firefighter]

On a scale of 1 (being the worst intake ever) and 1,000,000 (being the ultimate intake), I would rate it 738,543 out of 1,000,000.

LMAO hahahahahahahahaha

[butterfingers]

in your honest opinions

is there any point upgrading to a gruppe m

if i already have a injen CAI, and have no set plans for a tune?

[Lukezen27]

in your honest opinions

is there any point upgrading to a gruppe m

if i already have a injen CAI, and have no set plans for a tune?

Nope

Char

[Perry]

How does the Mugen intake compare to the Grupe M?


If your running stock at the moment I'll suggest go with the GruppM.

[CrazyPotato]

Hey Guys,

I need help with comprehensive car insurance for a 2005 EP3 before I go buy it.

I've got two online quotes from Just Cars and NRMA, but it is wayyyy too much roughly around 4k a year is that normal? btw I'm 18 years old

Do you guys know of another insurance company that would cover an EP3?

[Lukezen27]

Hey Guys,

I need help with comprehensive car insurance for a 2005 EP3 before I go buy it.

I've got two online quotes from Just Cars and NRMA, but it is wayyyy too much roughly around 4-5k a year is that normal? btw I'm 18 years old

Do you guys know of another insurance company that would cover an EP3?

Ouch

Sux to be 18

lol

[LittleDragon^^]

Hey Guys,

I need help with comprehensive car insurance for a 2005 EP3 before I go buy it.

I've got two online quotes from Just Cars and NRMA, but it is wayyyy too much roughly around 4-5k a year is that normal? btw I'm 18 years old

Do you guys know of another insurance company that would cover an EP3?

Holy crap!
I'm 28 and I just insured my car through Shannons - lowest price, lowest excess, best incentives for no claims.

[CrazyPotato]

If I put the car under my dads name insurance would be affordable, but once I list my name as one of the drivers it goes through the roof.

I know with Just Cars it says you must state the youngest driver, but with NRMA it says list any regular driver so can I not be listed and still be covered and argue that I'm not a regular driver if something was ever to happen?

[geeang]

If I put the car under my dads name insurance would be affordable, but once I list my name as one of the drivers it goes through the roof.

I know with Just Cars it says you must state the youngest driver, but with NRMA it says list any regular driver so can I not be listed and still be covered and argue that I'm not a regular driver if something was ever to happen?

Not likely, all insurance companies have teams of investigators who see this exact same story all day everyday. It would be highly unlikely for them to believe your dad is the owner and daily driver of a Civic Type R (demographic profiling, bad but it's the way it works), while you just drive it every now and then.

You see the odd person getting away with it because they never have to make a claim so it's never investigated, but if you have an accident then pray you're not one of the cases where your insurance policy is cancelled and you are held liable for potentially hundreds of thousands of dollars in damages.

[-JC-]

I love being a 34yr old EP3 tragic . . . Shannon's look after me for $52 a month!

[markkkwan]

Hi everyone!
I just bought an ep3 so i thought i'd introduce my self here!
It's basically stock except for Pedders Coilovers and an s2000 Steering wheel.
First mods probably be I/H/E, obviously
Thinking GruppeM after what i've read here, but also don't wanna pay that much for an intake, because i'm a cheapo.
AEM v2 was also high on the list along with the Injen CAI. if anyone has any comments about these that be awesome (or want to sell me one) =] (i know about the search function)
Was also wondering what kind of oils you guys use because i wanna service my car relatively soon
Anyways, thanks for reading this!

[geeang]

Hi everyone!
I just bought an ep3 so i thought i'd introduce my self here!
It's basically stock except for Pedders Coilovers and an s2000 Steering wheel.
First mods probably be I/H/E, obviously
Thinking GruppeM after what i've read here, but also don't wanna pay that much for an intake, because i'm a cheapo.
AEM v2 was also high on the list along with the Injen CAI. if anyone has any comments about these that be awesome (or want to sell me one) =] (i know about the search function)
Was also wondering what kind of oils you guys use because i wanna service my car relatively soon
Anyways, thanks for reading this!

I have an INJEN CAI for EP3R (replaced with GruppeM for wank-factor), but only if you're in NSW lol

[markkkwan]

haha i would love that, unfortunately i'm not in NSW
i'm from Melbourne. Thanks for the reply though!

[doosra]

If I put the car under my dads name insurance would be affordable, but once I list my name as one of the drivers it goes through the roof.

I know with Just Cars it says you must state the youngest driver, but with NRMA it says list any regular driver so can I not be listed and still be covered and argue that I'm not a regular driver if something was ever to happen?

Nrma will cover any driver.. Haven't u seen the ad. Lol

[-JC-]

Nrma will cover any driver.. Haven't u seen the ad. Lol

Be careful with that, I am reliably informed that this is only true when the owner of the car is actually IN the car with the driver . . .

[TonyxTony]

Anyone know anything about putting a roof rack for surf board on the ep3? What model and how much would be good. Thanks

[CrazyPotato]

All sorted out called them up, they said the car can be under my parents name and if I crash I just have to pay a higher excess fee.

[Lukezen27]

All sorted out called them up, they said the car can be under my parents name and if I crash I just have to pay a higher excess fee.


Nice!

[doosra]

All sorted out called them up, they said the car can be under my parents name and if I crash I just have to pay a higher excess fee.

That's what I thought, the ads would be completely misleading otherwise.. "reliably informed" haha

[doosra]

When I enquired about Nrma, they quoted me an extremely high amount compared to just car.

[butterfingers]

Anyone know anything about putting a roof rack for surf board on the ep3? What model and how much would be good. Thanks

Please don't...

[bennjamin]

Please don't...

Man

No one can spend all day at the track in their EP3.
For 99% of driving - a roof rack is quite practical. And they right
One looks decent. Just don't do it for image !


OP can I suggest it may be difficult finding due to the car being a coupe. You might find something that suits a Local non ep3 civic ?

EDIT read this thread - might help you out

http://forums.clubep3.com/showthread.php?t=791102

[butterfingers]

Man

No one can spend all day at the track in their EP3.
For 99% of driving - a roof rack is quite practical. And they right
One looks decent. Just don't do it for image !


OP can I suggest it may be difficult finding due to the car being a coupe. You might find something that suits a Local non ep3 civic ?

EDIT read this thread - might help you out

http://forums.clubep3.com/showthread.php?t=791102

I wasn't referring to track

[curtis265]

Please don't...

i don't seen an issue here.

If i had a car which could have roof racks, i'd be carrying all kinds of things on it

[LittleDragon^^]

i don't seen an issue here.

If i had a car which could have roof racks, i'd be carrying all kinds of things on it

Agreed.

The EP3 appealed to me cause it was FUN, fast, non-turbo (less problems) and practical. I wouldn't mind installing a roof rack one day to carry bikes to fun riding places.

[brody]

hey guys.

Have 225/45/17's waiting to be put on, wouldn't mind getting some new wheels as well. Just thought Id grab opinions on width and offset. may or may not be getting spoon/brembo calipers so I may take that into consideration when chosing offest.
Was thinking 17x9 +40/17x8.5 +38 etc not too sure on the offset as I havent looked into what the rpf1 offers. Would be great if anyone could give us their opinion.. or better yet.. what your running at the mo.
Cheers:)

[brody]

$1000 for an intake or whatever they're going for now. It's ridonkulous. Go Injen or aem. Just make sure you go cold air. I had an AEM and it was great (Easy enough to install and I guess you notice a slight throttle response change. Oh and that sexy note if you dont yet have an exhaust:P)


Hi everyone!
I just bought an ep3 so i thought i'd introduce my self here!
It's basically stock except for Pedders Coilovers and an s2000 Steering wheel.
First mods probably be I/H/E, obviously
Thinking GruppeM after what i've read here, but also don't wanna pay that much for an intake, because i'm a cheapo.
AEM v2 was also high on the list along with the Injen CAI. if anyone has any comments about these that be awesome (or want to sell me one) =] (i know about the search function)
Was also wondering what kind of oils you guys use because i wanna service my car relatively soon
Anyways, thanks for reading this!

[Symphorced]

hey guys.

Have 225/45/17's waiting to be put on, wouldn't mind getting some new wheels as well. Just thought Id grab opinions on width and offset. may or may not be getting spoon/brembo calipers so I may take that into consideration when chosing offest.
Was thinking 17x9 +40/17x8.5 +38 etc not too sure on the offset as I havent looked into what the rpf1 offers. Would be great if anyone could give us their opinion.. or better yet.. what your running at the mo.
Cheers:)

Those specs will not fit over Spoon calipers. If you go 9s you'll need at least +30 to clear the calipers.

[brody]

I see I see. I just cant decide. Could've had these wheels months ago. I get lazy. Thanks though:)


Those specs will not fit over Spoon calipers. If you go 9s you'll need at least +30 to clear the calipers.

[Lukezen27]

How do you guys clear round the back side windows?

There's that little gap that's close to impossible to get into!

[TanitY]

Hopefully this might help some body with o2 sensor problems for the EP3.

As you guys may know sourcing o2 sensors are a pain in the ass for the EP3's in Australia. It's best to source DC5R o2 sensors. The primary from the DC5R bolts up perfectly to the EP3 manifold, but the secondary from the DC5R is way too short for the EP3. To fix this problem just splice up the secondary o2 sensors and wire up the DC5r sensor to the EP3 o2 sensor wires as they are longer and will be able to reach.

Soldering is not possible with the type of wires they use for O2 sensors, as it's some special kind of metal that won't bond properly with soldering ion, so to connect the wire's up use crimp on connectors instead.

[KIKNHRD]

Hopefully this might help some body with o2 sensor problems for the EP3.

As you guys may know sourcing o2 sensors are a pain in the ass for the EP3's in Australia. It's best to source DC5R o2 sensors. The primary from the DC5R bolts up perfectly to the EP3 manifold, but the secondary from the DC5R is way too short for the EP3. To fix this problem just splice up the secondary o2 sensors and wire up the DC5r sensor to the EP3 o2 sensor wires as they are longer and will be able to reach.

Soldering is not possible with the type of wires they use for O2 sensors, as it's some special kind of metal that won't bond properly with soldering ion, so to connect the wire's up use crimp on connectors instead.

Im currently looking for a primary sensor but can only seem to get one from honda and they want $450. If anyone has a part number either denso or another brand that would be awesome.

[geeang]

Sadly it's time for me to part with my EP3, loved this car more than any I've owned before.

Anyone interested in a 2004 Facelift EP3R in Sydney? :D

Will be listing her up soon :'(

http://img.photobucket.com/albums/v352/viet_mafia/DSC_0076_zpsd86a778b.jpg

[bluey45]

Sadly it's time for me to part with my EP3, loved this car more than any I've owned before.

Anyone interested in a 2004 Facelift EP3R in Sydney? :D

Will be listing her up soon :'(

http://img.photobucket.com/albums/v352/viet_mafia/DSC_0076_zpsd86a778b.jpg

Very nice ep3. Good luck with sale. :)

Makes me sad as well. Brings back memories , as I also sold my ep3 couple weeks ago.

[butterfingers]

Those specs will not fit over Spoon calipers. If you go 9s you'll need at least +30 to clear the calipers.

If you have cr-Kai, +38 will JUUST clear them

[Lukezen27]

my rims are up for sale

http://www.ozhonda.com/forum/showthread.php?172699-18-quot-WORK-Emotion-CR-Kai-37-amp-42-off-set-(REAL)-With-New-Rubber-1000

Your EP3R needs Rolls Guards for these to fit

[Perry]

Sadly it's time for me to part with my EP3, loved this car more than any I've owned before.

Anyone interested in a 2004 Facelift EP3R in Sydney? :D

Will be listing her up soon :'(

http://img.photobucket.com/albums/v352/viet_mafia/DSC_0076_zpsd86a778b.jpg

Why is everyone selling.

[geeang]

Why is everyone selling.

Lol I don't know about everyone else, but I'm just selling to fund a new car.

[Perry]

Lol I don't know about everyone else, but I'm just selling to fund a new car.

Ohh what you getting pm me if you want :)

[geeang]

Ohh what you getting pm me if you want :)

LOL it's a secret for now, besides your inbox is full!

[Perry]

LOL it's a secret for now, besides your inbox is full!

Woops cleared now

[doosra]

I have noticed everyone is selling up as well... Might just keep mine forever if I can, all the money wasted on mods, it's not even worth selling anymore...

[Lukezen27]

I have noticed everyone is selling up as well... Might just keep mine forever if I can, all the money wasted on mods, it's not even worth selling anymore...

I'm planing to re-buy once I have a house loan :)

maybe or a new TYPE-R

[Symphorced]

For the people that have upgraded their rear sway bars, did you also buy a subframe reinforcement kit?

[UNA91]

For the people that have upgraded their rear sway bars, did you also buy a subframe reinforcement kit?

Running whiteline 24mm adjustable rear sways, and its fine. I think the ep3/dc5 subframes are alot beefier than older hondas

[butterfingers]

i will sell mine when i can afford a 1M coupe

[Symphorced]

Running whiteline 24mm adjustable rear sways, and its fine. I think the ep3/dc5 subframes are alot beefier than older hondas

I figured so too. Only ever hear of subframes in EG/DC/EKs being ripped out.

Ordering Cusco 25mm next month - in time for Honda Nats. Getting way too much body roll at the moment.

[Perry]

I figured so too. Only ever hear of subframes in EG/DC/EKs being ripped out.

Ordering Cusco 25mm next month - in time for Honda Nats. Getting way too much body roll at the moment.

Are you still running stock at the moment on the front?

[Symphorced]

Are you still running stock at the moment on the front?

Still running stock. Think I should look into upgrading that at the same time?

[Perry]

It all depends on what you want on your setup I guess. If your going bigger on the rear might as well change the front.

[LD_Mart]

has anyone got a link to a DIY on an Injen CAI install?

[mocchi]

has anyone got a link to a DIY on an Injen CAI install?

what so hard abt it
gotta cut bit of your fender liner though

[CrazyPotato]

Should be able to pick up my 05 EP3R at IMG some time this week, will officially be a part of the EP3 family soon :)

[bluey45]

Should be able to pick up my 05 EP3R at IMG some time this week, will officially be a part of the EP3 family soon :)

Congrats :)

[doosra]

Should be able to pick up my 05 EP3R at IMG some time this week, will officially be a part of the EP3 family soon :)

Congrats mate.. start saving for the mods :)

[Perry]

Should be able to pick up my 05 EP3R at IMG some time this week, will officially be a part of the EP3 family soon :)

Congrats dude

[stienerv2]

Congrats mate.. start saving for the mods :)

Nah man, always maintenance and repairs first. Its a lot better in the long run and enjoy appreciate the car in stock form for awhile.

[bluey45]

Nah man, always maintenance and repairs first. Its a lot better in the long run and enjoy appreciate the car in stock form for awhile.

Yeah that is true. First thing I did when I got mine was a big clean, full service and new engine mounts. :)

[UNA91]

Theres been a weird rattling/thudding noise that i can hear and even feel sometimes from 2k-3k rpm, and it started after i changed my transmission mount to hasports. It only happens in really wet weather (such as this depressing rain lately) and when its dry or even in light rain it doesn't happen. I suspect its my exhaust rattling on the underbody cause i can feel it at my feet...

[CrazyPotato]

Get my car on Tuesday instead.

[CrazyPotato]

Yeah that is true. First thing I did when I got mine was a big clean, full service and new engine mounts. :)

How bad are the OEM EP3 engine mounts? is it a must to upgrade to aftermarket ones or can I stay with OEM ones?

[CrazyPotato]

Nah man, always maintenance and repairs first. Its a lot better in the long run and enjoy appreciate the car in stock form for awhile.

Yeah, ill be enjoying the car in its stock form for awhile before going into mods, as it will give me to time to pay off uni fees and stuff.

[UNA91]

I've bought some new NGK spark plugs that are gapped at 1.1mm (OEM specification); but upon putting them in, I found that the car had HKS spark plugs and from research they were gapped to 0.8mm; they also looked in good condition, no black burn marks or anything, like they haven't been put in long ago.

Just wondering is there a difference or any advantage in using a smaller than OEM spark plug gap?

[LD_Mart]

Does anyone else have poor radio reception in there ep3?
I just installed an aftermarket head unit because i had some Japanese one in there and noticed that the radio is always cutting in and out?
Is there some type of special adapter i need because the car is jap?

[bluey45]

How bad are the OEM EP3 engine mounts? is it a must to upgrade to aftermarket ones or can I stay with OEM ones?

The oem ones are fine, but you'll find that having them replaced engine feels more planted when you put the power down, also minimises chance of mounts breaking/leaking as the mounts probably haven't been changed since beginning.
As I drove mine quite a bit I replaced mine with mugen mounts. Only a little bit more stiffer than oem, didn't want to be too hard.

[bluey45]

Does anyone else have poor radio reception in there ep3?
I just installed an aftermarket head unit because i had some Japanese one in there and noticed that the radio is always cutting in and out?
Is there some type of special adapter i need because the car is jap?

I had a aftermarket unit as well, didn't have any issues. Probably just a wiring thing?

[bluey45]

Anyone interested in some ep3 parts? I'm selling some left over from my ep3 sale.
Pm me if you interested.

[doosra]

I had a aftermarket unit as well, didn't have any issues. Probably just a wiring thing?

I've noticed of late that 2dayfm reception has gone worse... Mainly around my area cabramatta.. Other than that it's not too bad

[DreadAngel]

Still running stock. Think I should look into upgrading that at the same time?

Is it just body roll you want to clamp down on or is it understeer too?

Personally if its understeer that you're aiming at then do just the rear first, the RSB will have the biggest effect. Then you can decide whether or not you need to balance it with the FSB. It also depends what alignment and tires you have.

[Symphorced]

Is it just body roll you want to clamp down on or is it understeer too?

Personally if its understeer that you're aiming at then do just the rear first, the RSB will have the biggest effect. Then you can decide whether or not you need to balance it with the FSB. It also depends what alignment and tires you have.

Trying to reduce both. So much bodyroll and understeer is always apparent. Running aggressive alignment and sticky tyres already (-3.5 camber front with 2mm toe out, -2.5 camber rear with 1mm toe in on Hankook RS3s). I'm going to be ordering the Cusco rear sway bar soon and see how that goes before changing anything else.

[DreadAngel]

Trying to reduce both. So much bodyroll and understeer is always apparent. Running aggressive alignment and sticky tyres already (-3.5 camber front with 2mm toe out, -2.5 camber rear with 1mm toe in on Hankook RS3s). I'm going to be ordering the Cusco rear sway bar soon and see how that goes before changing anything else.

Sorry to ask for more details man, but what suspension are you running [spec, spring rate, damper setting, height, etc] might be able to help you further as well =)

[Symphorced]

Sorry to ask for more details man, but what suspension are you running [spec, spring rate, damper setting, height, etc] might be able to help you further as well =)

No need to apologise when you're offering me help and advice!

I'm on BC Racing BR coilovers (6kg/mm front, 8kg/mm rear), height I'm running about 100m off the ground. Damper is set to around 22 from softest (out of the 32). Other suspension mods include: inverted tie rod ends, shortened tie rods, rear camber arms and various bracing across the car (6 point bolt-in cage, front strut brace, rear tie brace, rear strut brace). The coilovers are definitely something I'm looking to upgrade in the future.

[DreadAngel]

Do you have a video of you running by any chance so I can see when you're experiencing the under & roll?

Does it happen under power only? Or under trail braking? Or everywhere?

I'm assuming your car isn't too ample in the power/torque department and that your LSD is still good =)

Alignment wise looks ok from what I can see.

Tires are good, did you run the car with different tires? Possibly with less grip? Did the car under @ same or different speed? Was the under same or worse?

Damper wise 22 clicks front only? or is that front and rear? I'll be helping my friend dial in his EP3R on the weekend, I think he might have the same coilovers as you, I'll share what I did regardless =)

EDIT - Atm, most indications would point to some damper retweaking and RSB with FSB pending whether you like the changes or not... Cause depending on the diameter and construct of your chosen swaybar [Hollow v Solid], it might make the rear so stiff that you get an excitable rear end so that's when you balance it with a slightly larger FSB =)

[Symphorced]

Under trail braking I don't get too much body roll/under. It's usually after hitting the apex of the corner and under throttle that I will get understeer/body roll.

Run with Toyo R1Rs front and Re050A rears before. That was getting me lift off oversteer more than anything due to the poor condition of the rear tyres. Dampers - I've run 22 all round before and also 22 front/24 rear. Didn't notice a difference.

Closest I have to a video is from a video mounted to the dash of a chasing car.. but that doesn't show much of me through corners and the tyres you hear are of his car.

http://www.facebook.com/video/embed?video_id=10151410699285605

This is the amount of body roll I get upon exit of a corner:

http://24.media.tumblr.com/aff3b5c2438910fc7291c145c6be4c61/tumblr_mhjkt2kT9z1qmeqt7o1_1280.jpg

[viett]

Hey does anyone know why my fuel millage is so terrible? I'm getting about 320KM to a full tank.

Vtecing it here and there, but not so often.

[DreadAngel]

Check below =)

NB: Because you're running a JDM Import, do expect the mapping to be not so correct for Australian conditions, majority of imports doesn't matter if you're running an EP3 or a GT-R, run rich from factory .

[b]Checklist
Air Filter - Clean or Not
Spark Plugs - Electrode
Spark Plug Leads - Check overall condition including the plug cover end

02 Sensor - This can affect performance and economy...
Fuel Filter - You'll be surprised how many people neglect this...
Fuel Pump - Check to see if it's making noises, sign it could be on the way out

That's just some general stuff =)

[DreadAngel]

Under trail braking I don't get too much body roll/under. It's usually after hitting the apex of the corner and under throttle that I will get understeer/body roll.

Run with Toyo R1Rs front and Re050A rears before. That was getting me lift off oversteer more than anything due to the poor condition of the rear tyres. Dampers - I've run 22 all round before and also 22 front/24 rear. Didn't notice a difference.

Closest I have to a video is from a video mounted to the dash of a chasing car.. but that doesn't show much of me through corners and the tyres you hear are of his car.

http://www.facebook.com/video/embed?video_id=10151410699285605

This is the amount of body roll I get upon exit of a corner:

[img]http://24.media.tumblr.com/aff3b5c2438910fc7291c145c6be4c61/tumblr_mhjkt2kT9z1qmeqt7o1_1280.jpg[/ig]

If I play with my friend's damper settings on Saturday, will report back, I'll check your vid when I'm home =)

[butterfingers]

Check below =)

NB: Because you're running a JDM Import, do expect the mapping to be not so correct for Australian conditions, majority of imports doesn't matter if you're running an EP3 or a GT-R, run rich from factory .

[b]Checklist
Air Filter - Clean or Not
Spark Plugs - Electrode
Spark Plug Leads - Check overall condition including the plug cover end

02 Sensor - This can affect performance and economy...
Fuel Filter - You'll be surprised how many people neglect this...
Fuel Pump - Check to see if it's making noises, sign it could be on the way out

That's just some general stuff =)

fuel filter is a big one, and affects mileage as well as performance, and over looked a lot

[viett]

fuel filter is a big one, and affects mileage as well as performance, and over looked a lot

Where could I get a new fuel filter and get it installed? How much do you reckon this will cost?

[DreadAngel]

Honda will have, there should also aftermarket alternatives...

Installed well there are DIY guys and workshops that can do it for you =)

[butterfingers]

Where could I get a new fuel filter and get it installed? How much do you reckon this will cost?

most honda specialsts will have it or can order it when you go for your major service

[viett]

http://www.tegiwaimports.com/genuine-oem-honda-fuel-filter-civic-type-r-ep3-k20a-3154/

is this the fuel filter I'll be needing?

[geeang]

http://www.tegiwaimports.com/genuine-oem-honda-fuel-filter-civic-type-r-ep3-k20a-3154/

is this the fuel filter I'll be needing?

You're asking if the EP3 Type R fuel filter will be what you need for your EP3 Type R? LOL

[doosra]

http://www.tegiwaimports.com/genuine-oem-honda-fuel-filter-civic-type-r-ep3-k20a-3154/

is this the fuel filter I'll be needing?

Wow that's really cheap.. They're like 120-130 from honda

[uniqlo]

The manual I've got shows the fuel filter to be in the fuel tank.
The one posted is external.
I believe most cars post 2000 only have in-tank filters

[doosra]

Yeah I think that's wrong one. Get it from jdmconcept only $80 http://www.jdmconcept.com.au/part/oem-honda/fuel-filter/civic-ep3-01-05

[butterfingers]

if its something like a fuel filter i suggest going to Top One if youre in sydney.

personally i wouldnt **** around with any internal things incase my car explodes next time i drive it

[butterfingers]

anyone recommend good shortened tie rod ends?

[Symphorced]

anyone recommend good shortened tie rod ends?

Tie rod ends don't get shortened. You mean the tie rods themselves? Or are you after inverted tie rod ends?

[stienerv2]

shorten tie rods are awesome! more camber lol

[dnapol]

shorten tie rods are awesome! more camber lol

+1

Got -3 with just tie rods and camber tops. More with bolts!

[viett]

Hey guys I have a quick question.
The previous owner of my car had a Toda racing exhaust system installed, would that affect the O2 sensor which could be the reason for my terrible fuel inefficiency?
I just poured in a bottle of fuel flush today so if the fuel inefficiency doesn't get any better than I'm assuming it's the O2 sensor.

Could it be damaged or just dirty?

[doosra]

How many km's are u getting per 10L? Might be spark plugs.. If your averaging 100km/10L then you're fine

[viett]

No where near close 100km/10L, I'm getting about 320KM to a full tank.

[butterfingers]

are you sure its a full tank? ive gotten almost 100km out of the tank when the light turned on.

[viett]

Pretty close to a full tank, I mean I fill it up till the click, wait 5 seconds and fill it till the 2nd click.

I'm certain they'res something wrong with my car.

[geeang]

Pretty close to a full tank, I mean I fill it up till the click, wait 5 seconds and fill it till the 2nd click.

I'm certain they'res something wrong with my car.

How many litres do you then fill up when it's 'empty'?

[doosra]

You need to measure by how many km's to litres poured as fuel indicator light may give false readings.. I think an ep3 tank is about 50L. Drive 100km and fill up and see how many litres it uses. On average use 10L per 100km

[viett]

I just calculated it and yesterday I filled up about 44L, spending around $75 with Vpower being $1.70.
I'll let you know how far I get with this tank, this is with the fuel flush mixed in this tank.

But I know for certain they'res something wrong, I've logged my past fill ups, and for the last 5 full tanks I haven't been able to get over 330KMs till the light appears. I was expecting at least 400kms.

[doosra]

If u got 330km/44L there must be something wrong. Try changing your spark plugs as I've heard they can be the cause of heavy fuel consumption

[butterfingers]

when my light appears im usually at the 300lm mark

when i refill, it takes in around S45-55 of ultimate at $1.70/L before its full.

[doosra]

Must be vtecing 24/7

[Symphorced]

Must be vtecing 24/7

All day, erryday son.

[mocchi]

All day, erryday son.

lmaoo

[Poeter]

I just calculated it and yesterday I filled up about 44L, spending around $75 with Vpower being $1.70.
I'll let you know how far I get with this tank, this is with the fuel flush mixed in this tank.

But I know for certain they'res something wrong, I've logged my past fill ups, and for the last 5 full tanks I haven't been able to get over 330KMs till the light appears. I was expecting at least 400kms.

Also check if you got OEM ecu. There's a possibility your car came with a race ecu.

My friend's ep3 was also pondering why he can't achieve 400km per tank.

He figured that his car came with a race ecu (impact! - some random japanese brand who has some affiliation tracy sport).

[bluey45]

Also check if you got OEM ecu. There's a possibility your car came with a race ecu.

My friend's ep3 was also pondering why he can't achieve 400km per tank.

He figured that his car came with a race ecu (impact! - some random japanese brand who has some affiliation tracy sport).

That's a nice surprise with a race ecu

[viett]

Also check if you got OEM ecu. There's a possibility your car came with a race ecu.

My friend's ep3 was also pondering why he can't achieve 400km per tank.

He figured that his car came with a race ecu (impact! - some random japanese brand who has some affiliation tracy sport).

Hahaha would love it if it came with a race ecu although it's killing my petrol.

[integraR]

Hahaha would love it if it came with a race ecu although it's killing my petrol.

check tyre pressure as well

how many km's before light comes on

[dnapol]

I get just under 400 when light comes on. Stock ecu. Although I pop with my skunk2 exhaust (runs rich) and I drive with vtec a lot :P

[viett]

check tyre pressure as well

how many km's before light comes on

At the 300KM mark is when the light usually comes on.

[butterfingers]

I get just under 400 when light comes on. Stock ecu. Although I pop with my skunk2 exhaust (runs rich) and I drive with vtec a lot :P

pop or burble? if it crackles/burbles on decel its not from running rich, its a different sound from lift off pop.

btw put up a vid of your skunk2 exhaust, havent heard one on an ep3 before

[viett]

http://imageshack.us/photo/my-images/28/img2871xb.jpg
Is this the stock ECU?

Also I found this UNDER the glove box, anyone know what it is?

http://imageshack.us/photo/my-images/21/img2874w.jpg/

It says Mitsubishi motors on it.

[Lukezen27]

http://imageshack.us/photo/my-images/28/img2871xb.jpg
Is this the stock ECU? Correct

Also I found this UNDER the glove box, anyone know what it is?

http://imageshack.us/photo/my-images/21/img2874w.jpg/ might be for the a/c or something

It says Mitsubishi motors on it.

Don't go pulling things out if you don't know what they are lol

Char

[Poeter]

http://imageshack.us/photo/my-images/28/img2871xb.jpg
Is this the stock ECU?

Also I found this UNDER the glove box, anyone know what it is?

http://imageshack.us/photo/my-images/21/img2874w.jpg/

It says Mitsubishi motors on it.


The top pic looks pretty stock. Although there could be more labelings.

But a race ecu usually has a sticker like this

https://encrypted-tbn1.gstatic.com/images?q=tbn:ANd9GcTMT7FusrjYR7SLd-dtxTmSopA22m_qw-6kxvYM3hC0a_UWPqw1

For the second picture, it's the steering cpu based on the part number.

http://www.garagelive.jp/auctions/index/87119250

[doosra]

408kms and still no light yet.. This is all peak hour driving from cabra to north Sydney everyday.... Filled up only 41L.. Love me ep3, such a great car for a daily.

http://img46.imageshack.us/img46/4608/20130315182008.jpg (http://img46.imageshack.us/i/20130315182008.jpg/)

[viett]

408kms and still no light yet.. This is all peak hour driving from cabra to north Sydney everyday.... Filled up only 41L.. Love me ep3, such a great car for a daily.

http://img46.imageshack.us/img46/4608/20130315182008.jpg (http://img46.imageshack.us/i/20130315182008.jpg/)

****kk, me jelly bro.

[doosra]

Haha sorry for rubbing it in.. :) How long have u had ur ep3 for and has it been like that since u got it?