***Official What did you do to your EK today***

[Spoon-Accord]

http://www.youtube.com/watch?v=brJTEQuvCJE

i stuck with this exhaust because i got defected for my previous cannon muffler (Vision N1)

this muffler whilst driving its really un-noticable, only time it really becomes alive is when i'm coasting in a high gear or rev towards rev limit.

PHO might have a few opinions on it, he took my car for a drive a few times and no ones ever complained LOL

[mugen_ctr]

i love how people quote things from what they have read and then try to make out they know 1st hand about it
have you ever owned a 5-10 yr old quality exhaust at all

no point arguing if you dont have any experience

Dont just assume non of us have ever owned a jap spec cat back ;)... Ive already gone through 2 setups, 5zigen cat back and Vision N1 cat back which i have atm... Quality is top notch, welds are exceptional! BUT those were built only 10 - 5 yrs ago, fastward now, u can pickup a new cat back for lesser price $500 - $800 vs $1500 for a jdm cat back minus the shipping an taxes


my 15 yr old mugen twin loop is still working how it should be too
it only made 1-2kws on my butt dyno but
so it makes it inferior to the examples you mentioned

Inferior from a performance POV, build quality is top notch, theres no deny it, but how can anyone spend and justify say 1500 - 800 and only expect a gain of 1-2kw Lmaooooooo....

Sorry man but just goes to show that mugen made a shit performance product an slapped a massive price tag much like ARC which went bankrupt! All eye candy an no performance gains at all

[90LAN]

so who would pay 1500-1800 for a 2nd hand exhaust ?
so have you owned a mugen twin loop is the question not owning a jdm exhaust ?
so why have you got a jdm exhaust when you reackon jdm is shit as mentioned earlier
what do you think the vision exhaust would of cost if you had to buy it new from japan .........
the original topic of discussion was between a $800 x force twin loop and a used twin loop for about the same amount the money

[90LAN]

you must have a massive price tag exhaust too, because vision went bust too if you didnt know

[MYEK9]

wtf, how do you justify buying fake exhausts, look at the replica N1 compared to the real N1 , the difference of noise is unbelieveable.. If your going to go an exhuast for a jap car, source it directly from japan.. Like everyone always goes on about X-FORCE, next minute 10,000 complaints upon the forum regarding their headers cracking and problems with their e systems,

Work up the money and spend the bit extra and get something that will make the difference. Everyone's opinion to their own i guess.

I have custom exhaust that should fit your car matt if your looking at changing the system.

[MYEK9]

After going with a jasma approved spoon b-pipe and spoon n1 axle back, There is not a chance that i would go anything else , not even mugen.. next thing is toda headers which are on hold for me!

[mugen_ctr]

you must have a massive price tag exhaust too, because vision went bust too if you didnt know


so who would pay 1500-1800 for a 2nd hand exhaust ?
so have you owned a mugen twin loop is the question not owning a jdm exhaust ?
so why have you got a jdm exhaust when you reackon jdm is shit as mentioned earlier
what do you think the vision exhaust would of cost if you had to buy it new from japan .........
the original topic of discussion was between a $800 x force twin loop and a used twin loop for about the same amount the money

Depends on what exhaust ur talking about... there are always ppl willing to fork out money for anything, so in relation to ur question champ yes ppl will pay for em ;)

LOL u jus asked me about owning a qulity jdm exhaust now this???? twin loop.... i dont own one, nor did i ever have the intentions to buy one, ive seen them in the flesh, have been in the car with one, as ive said quality is top, performance valve is shit...

Where did i ever mention JDM is shit? i must be blind cause All i said was Mugen twin loop is a crap house design thats over priced that wont net u any real world performance gains!! hahaha

I can tell u right now Given the rough estimate, $1500 easy! for most jap spec cat backs new so vision much like any in-house Japanese company

And for argument sake the X-force would be the better one to buy

a) its new!
b) IT flows better an will perform better as its a true 60mm exhaust all the way from cat to muffler canister and the piping that snakes into the canister
c) Its local and will fit on our ADM vehicles with no mods
d) If any problems will arise xforce has warranty

[EKVTIR-T]

this mugen tissue box way better quality than those cheapo ones,lightweight but strong and also has brag power too

http://s16.postimage.org/8n5oc4b3p/Carbon_Fiber_Staff_01.jpg

[MYEK9]

Their is nothing to brag about , and yes the tissues might come out eaiser due to the aero dynamics of the box.

Aussie brands cannot compare to a jap brand. Designed from the birth place of your car,

[lolmclol]

Swifter to your nose, softer on your skin!

[MYEK9]

u might as well get a redback exhaust with a chevy badge and slap it on your honda

[newpaddy3]

u might as well get a redback exhaust with a chevy badge and slap it on your honda

#swag

[mugen_ctr]

LOL so all those big brand companies in japan that use our Aussie Haltech must be doin it wrong???? So the Cyber EVO in japan must use only jdm parts???

Cmon dude be realistic.... Japan isnt what it use to be back in the 90's, Nowadays anyone can design and build parts just as good if not better than japan...

i like the way some ppl think on ozhonda :D

an FUUUUKKKKKKK JDM tissue box... X10 points at JDMST meets from now on!!! SHIIET!!!

[90LAN]

oh shit, you sat in a car with a mugen twin loop and read some where it doesnt make any power
ok ill better listen to you about this one that a x force muffler is better.
your butt dyno must be working real well
i guess 99% of ozhonda p platers would say the same as you that x force is better

[90LAN]

oh i forgot to mention the mugen twin loop made 1-2 kws on my d series

[MYEK9]

LOL so all those big brand companies in japan that use our Aussie Haltech must be doin it wrong???? So the Cyber EVO in japan must use only jdm parts???

Cmon dude be realistic.... Japan isnt what it use to be back in the 90's, Nowadays anyone can design and build parts just as good if not better than japan...

i like the way some ppl think on ozhonda :D

an FUUUUKKKKKKK JDM tissue box... X10 points at JDMST meets from now on!!! SHIIET!!!

Well stated, i dont know i personally saw the difference myself dude, hence why im telling from experience..

But i guess it matters on your wallet to!

and yes i need the tissue box please , jdmconcept will charge you soon to breathe jdm air.

[PHO]

I drove my EK today.

[MYEK9]

I drove my EK today.


Can barely type , have been cut and polishing since 11.30am!

[90LAN]

just installed a all show no go exhaust
would any one want to swap a over priced hopeless exhaust for a x force twin loop ?

http://i144.photobucket.com/albums/r187/90LAN/MY%20EK/DSC_0073copy.jpg

[mugen_ctr]

oh shit, you sat in a car with a mugen twin loop and read some where it doesnt make any power
ok ill better listen to you about this one that a x force muffler is better.
your butt dyno must be working real well
i guess 99% of ozhonda p platers would say the same as you that x force is better

hahaha ur a intresting guy thats for sure ;)

But ive made my point and argument clear... Weather u choose to buy a JDM or ADM exhaust is really personal preference

an congrats on making 1-2kw on a d-series with a $800 cat back, im sure most guys would be interested to know what power figures they can expect spending that amount of money on a cat back and on a d16 engine


Well stated, i dont know i personally saw the difference myself dude, hence why im telling from experience..

But i guess it matters on your wallet to!

and yes i need the tissue box please , jdmconcept will charge you soon to breathe jdm air.

yea exactly man, all personal preferance an down to how deep ur pockets are

and back on topic, finally received my new 2.5 cat back from the states on friday :D

Just need a high flow cat, than it will be a true turbo back exhaust system yay :D:D:D

[PHO]

Mann lan. Wish I could get all cray parts like you.

Struggling here just doing the basic oem stuff so far :[

[newpaddy3]

just installed a all show no go exhaust
would any one want to swap a over priced hopeless exhaust for a x force twin loop ?

http://i144.photobucket.com/albums/r187/90LAN/MY%20EK/DSC_0073copy.jpg

Keen.

http://www.crazysales.com.au/products_pictures/23/2354_235837_extra.jpg

[MYEK9]

gime your visors lan , thats the next thing on my list of many things! :)

[MYEK9]

Also where did you get them from, been looking around for them.

[90LAN]

x force make a really good cat i heard or you could get one from america
just make sure you choose carefully as i heard and read that the cores blow out if you have too much power

[90LAN]

Also where did you get them from, been looking around for them.


yahoo -40 bucks del be under your budget of 200
or you could get some from china for 300
as mugen ctrless says everything is pretty much equally made these days or better

[90LAN]

Keen.

http://www.crazysales.com.au/products_pictures/23/2354_235837_extra.jpg

has to be x force as it is highly recommended on here

[PHO]

xforce is best.

for more push me in car

[MYEK9]

i never had a budget lol i dont think ..just asking where you got the visors from , and what shuld i be paying for them for an ek9

[eren]

so my muffler has to be replaced with xforce?

[eren]

http://i144.photobucket.com/albums/r187/90LAN/MY%20EK/DSC_0073copy.jpg
Cleeeeeeeeeeeeaaannnnnn AF

[EKVTIR-T]

MightyCarMod use and recommend Xforce and not just coz theyre contractually obligated k m8

[eren]

http://www.youtube.com/watch?v=brJTEQuvCJE

i stuck with this exhaust because i got defected for my previous cannon muffler (Vision N1)

this muffler whilst driving its really un-noticable, only time it really becomes alive is when i'm coasting in a high gear or rev towards rev limit.

PHO might have a few opinions on it, he took my car for a drive a few times and no ones ever complained LOL

doesnt really sound loud to me.

[carayan]

"What did you do to your EK today"


i bought one. heh

[newpaddy3]

MightyCarMod use and recommend Xforce and not just coz theyre contractually obligated k m8

They also painted a car with fence paint.

And riced up a perfectly fine civic.

And destroyed a subaru gearbox.

[90LAN]

so my muffler has to be replaced with xforce?


yeah mate, i have seen the light and going to order a x force twin loop from japan

[eren]

yeah mate, i have seen the light and going to order a x force twin loop from japan
LuL...

[mocchi]

mugen is just a knock off company anyway
just like voltex copying seibon.

buy genuine aussie product bro. xforce ftw.

[MYEK9]

cannot believe we are comparing MUGEN to XFORCE, they should not even be in the same sentence...

[PHO]

cannot believe we are comparing MUGEN to XFORCE, they should not even be in the same sentence...

i know right. xforce blows mugen out of the water.

mugen just cheap china crap

[lolmclol]

Mugen is subsidiary of great wall automotive

[MYEK9]

give you a dimsim and a can coke for xforce.

[eren]

too much sarcasm in this thread.
Srs tho . use this example

Bill likes xforce so he bought xforce and is going to use it .

bob likes mugen so he bought mugen and is going to use it.

if bill doesnt like bobs choice he should STFU.
if bob doesnt like bills choice he should also STFU.


me personaly like the brand ''Mugen'' better . but dont care about both . xforce actually copied mugens twinloop lul.

Enuff with the debate of a muffler haha . were talking about 1-5kw max difference .

[90LAN]

the topic before mugenless ctr jumped in was that for the price of a new xforce twin loop you could buy a real one that is used
i know which one i would get

[newpaddy3]

the topic before mugenless ctr jumped in was that for the price of a new xforce twin loop you could buy a real one that is used
i know which one i would get

xforce for that new reliability.

[eeko]

too much sarcasm in this thread.
Srs tho . use this example

Bill likes xforce so he bought xforce and is going to use it .

bob likes mugen so he bought mugen and is going to use it.

if bill doesnt like bobs choice he should STFU.
if bob doesnt like bills choice he should also STFU.


me personaly like the brand ''Mugen'' better . but dont care about both . xforce actually copied mugens twinloop lul.

Enuff with the debate of a muffler haha . were talking about 1-5kw max difference .

Lol 1-3kw difference per part when you add it up in I/H/E does make a difference in example when adding up a power gain.. Instead of 1kw gain per part compared to 2-3kw is the difference of 103kw atw to 108kw D:

Lol...

[Vvvtec]

What the fuk.

This thread delivers.

[PHO]

http://www.ozhonda.com/forum/customavatars/avatar30053_82.gif

[Spoon-Accord]

here are a few more pictures. currently both front and rears slammed

they are pretty short compared to my tein monoflexes at full slammed, might be interesting :)

also there is a valve at the bottom of each damper aswell, never seen such thing on any of the coilovers i've ever owned.

quality wise: best ever i've ever owned, period. even tho it isnt japanese made, props to the americans for such an effort.

http://img.photobucket.com/albums/v216/spoon-accord/IMG_1170_zps2ed10fb3.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1171_zps5713faa1.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1172_zpsc9555dbf.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1173_zps92a1fa1b.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1174_zpsfb28fa51.jpg

[Vvvtec]

Doesnt need to be jap to be good lol.

They look nice man, keen to hear how they feel.

[mattsrea]

Keen to see some pics of what it looks like when fitted KennyG! :)

[MYEK9]

mattsrea you going jdmst tommorow?

[RenzokukenJ]

Fak some interdasting shit here.

Jimmies rustled harder then gym thread ay

[Spoon-Accord]

Can't wait till there fitted too matt,just waiting on the rear forks to arrive and ill be set,ohh and brand new ek9 lip since I bought my ek9 with a genuine spoon lip (smashed it on a really tight turn)

[mattsrea]

mattsrea you going jdmst tommorow?

If your talking about the carribean then yrah im going for abit.

[mugen_ctr]

here are a few more pictures. currently both front and rears slammed

they are pretty short compared to my tein monoflexes at full slammed, might be interesting :)

also there is a valve at the bottom of each damper aswell, never seen such thing on any of the coilovers i've ever owned.

quality wise: best ever i've ever owned, period. even tho it isnt japanese made, props to the americans for such an effort.

http://img.photobucket.com/albums/v216/spoon-accord/IMG_1170_zps2ed10fb3.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1171_zps5713faa1.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1172_zpsc9555dbf.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1173_zps92a1fa1b.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1174_zpsfb28fa51.jpg

fukkn jelly! intresting how they dont use C-spanners though an use a allen key bolt to tighten up the collars


Doesnt need to be jap to be good lol.

They look nice man, keen to hear how they feel.

sorry champ has to be mugen an jdm to pass, cause apparently everything else is crap hahaha jkz


If your talking about the carribean then yrah im going for abit.

Hey man i might go this time hahahha hit me up man, keen to show u the little d series turbo banger!

[Spoon-Accord]

yeh there is a spanner!

makes it soooo easy to adjust aswell. just one and one only spanner

garanteed no slippage (unlike other branded coilovers with pair of spanners) actually split both knuckles on both hands

they come with detachable damper adjusters (when i got them, they werent installed, choose to have them on or off)
every coilover comes with their own set of nuts and spare pair
pretty descent packaging too, and equipped with all little bits and pieces :)

http://img.photobucket.com/albums/v216/spoon-accord/image_zps1c8da53e.jpg
http://img.photobucket.com/albums/v216/spoon-accord/IMG_1176_zpsd9bf1150.jpg

[mattsrea]

fukkn jelly! intresting how they dont use C-spanners though an use a allen key bolt to tighten up the collars



sorry champ has to be mugen an jdm to pass, cause apparently everything else is crap hahaha jkz



Hey man i might go this time hahahha hit me up man, keen to show u the little d series turbo banger!

Yeah waiting to see this turbo ej bro theres alot pf cars here!!

[ctx]

kenny_amr_sales_rep
Sent from my 7 Trophy using Board Express

[lolmclol]

stahlp_my_feathers_rustled

[Spoon-Accord]

Lol @eric , nooo, just telling peeps how nice they are

Sorry for the pictures and all the rubbish talk :)

[iceey]

painted my extractors with flameproof paint .. done all the step to let it dry

took it out for a spin and the thing still decided to burn -_-

[newpaddy3]

painted my extractors with flameproof paint .. done all the step to let it dry

took it out for a spin and the thing still decided to burn -_-

Inb4fencepaint

[viinnh]

http://sphotos-g.ak.fbcdn.net/hphotos-ak-ash3/526711_10200287008771435_1294520570_n.jpg

got my new wheels today. time to get some stretch going on !

15x7.5+12
15x8+11

currently 185/55/15 going to go 165/50/15 up front and 175/50/15 on the rear. relax its not my daily wheels.

[PHO]

Ud be weak if u think thats too crazy for daily.

Perfect specs :P


40profile would be crazy

[Riced_Civic]

Mounted IC, Radiator, repositioned IC pipes, new CF bonnet and aero catch pins (Still need to rivet the aero latches on).
Almost ready for nationals
http://i204.photobucket.com/albums/bb278/riced_civic/IMAG0085_zps9776b368.jpg

[mocchi]

wtb: garage space

[THE 2BSEEN]

I removed my door window sills stripped the black trim paint off. Sanded and polished, came up very nice.
Resprayed wiper and indicators

[viinnh]

Ud be weak if u think thats too crazy for daily.

Perfect specs :P


40profile would be crazy

well here it is
165/50/15 7.5" and 165/55/15 8"
http://sphotos-f.ak.fbcdn.net/hphotos-ak-ash3/562678_10200288171800510_354588279_n.jpg
http://sphotos-e.ak.fbcdn.net/hphotos-ak-ash3/5365_10200288065037841_102150482_n.jpg
****ed up thought i could run the wheels with no spacers, nek minnit running 8mm spacer up front just clears the caliper. =[
fronts are still high as shit
http://sphotos-g.ak.fbcdn.net/hphotos-ak-snc7/575964_10200288025316848_551865570_n.jpg
will lower it soon. the rears are perfect height i guess

photoshopped front end to my desire height
http://sphotos-c.ak.fbcdn.net/hphotos-ak-snc7/392867_228238577317037_300712855_n.jpg

[PHO]

Fuarkkk yes. 1" lower, camber arms. Your all sweet m8y

[mattsrea]

Looking sweet charles!

[ivseenwars]

In two minds with my EK currently. Keep and have minimal funds to build current EK or sell and build another EK/Integra with the money. Wants B series.

[carayan]

In two minds with my EK currently. Keep and have minimal funds to build current EK or sell and build another EK/Integra with the money. Wants B series.

keep it, getting another one will never feel the same. you put so much effort into this one, why let it go? just keep going, make it more awesome!

[THE 2BSEEN]

keep it, getting another one will never feel the same. you put so much effort into this one, why let it go? just keep going, make it more awesome!

Yeah agreed, I never sell
But I do have 11 car

[Alexx]

damn, a tire that short is really hard to pull off without being on the floor, and with the front bar thats going to be hard!

[mocchi]

Yeah agreed, I never sell
But I do have 11 car

none running

http://t1.gstatic.com/images?q=tbn:ANd9GcRfS4xOfbbI-tYrm-0Ubaxzv4Kf2C_D5do8wkxAyCINOiuNC7I

[viinnh]

think i might get a oem bar for daily and lower the car

i might jsut daily these wheels lolz

[PHO]

think i might get a oem bar for daily and lower the car

i might jsut daily these wheels lolz

Thats the way charles. YeahByuddy.

[THE 2BSEEN]

none running

http://t1.gstatic.com/images?q=tbn:ANd9GcRfS4xOfbbI-tYrm-0Ubaxzv4Kf2C_D5do8wkxAyCINOiuNC7I

All but one runs.

4 with rego, and a few share plates lol

[lolmclol]

All but one runs.

4 with rego, and a few share plates lol

hmmmm ...

[mocchi]

All but one runs.

4 with rego, and a few share plates lol

share plate lmao wat

2bseen crx king m8

[THE 2BSEEN]

share plate lmao wat

2bseen crx king m8

More a collector bro

My dark blue crx is registered as a black crx,
So I drive the ef7s when I need to

[Spoon-Accord]

http://img.photobucket.com/albums/v216/spoon-accord/image_zpse6e23a7f.jpg
she is back on the roads!*jump4joy*

[dorikin]

Lookin good

oem lip would be neat

[Spoon-Accord]

It's comin! :)

[carayan]

That is sick! Awesome colour

[viinnh]

http://i45.tinypic.com/2i6lzyt.jpg
http://sphotos-f.ak.fbcdn.net/hphotos-ak-ash3/601490_10200307267317886_1137873163_n.jpg

Lowered the front a bit more then went to the downshift meet.

and also got a OEM ek9 lip last night, haven't taken a photo yet.
looking for oem front bar now, condition does not matter

[pietroots]

I removed my door window sills stripped the black trim paint off. Sanded and polished, came up very nice.
Resprayed wiper and indicators

is there a thread on how to do that? because mine look pretty gross!

[Tosies]

Fresh rubber for tmr!

[THE 2BSEEN]

is there a thread on how to do that? because mine look pretty gross!

There is some where bro.

Pm me if you want any help

[integraR]

http://img.photobucket.com/albums/v216/spoon-accord/image_zpse6e23a7f.jpg
she is back on the roads!*jump4joy*

that championship whit is creamy

new respray?

[IEVAQ8]

got some track wheels and powder coated them up

http://i287.photobucket.com/albums/ll147/ievaq8/ek%20civic%20build/20130319_162052_zps6fda9cb2.jpg

[o0ultima0o]

DIY false floor and new black carpet
http://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1116.jpg
http://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1158.jpghttp://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1161.jpg

[nate92]

DIY false floor and new black carpet
http://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1116.jpg
http://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1158.jpghttp://i1267.photobucket.com/albums/jj542/ecnivecniv/CIVIC%20EK%20False%20floor%20and%20boot%20carpet/IMG_1161.jpg


Looking good!

[MYEK9]

where did you get the carpet from ?

[o0ultima0o]

where did you get the carpet from ?

bunnings. i have a lil DIY.
http://www.ozhonda.com/forum/showthread.php?173633-Replacing-false-floor-and-boot-carpet-Civic-EK1-Hatch

[dorikin]

Cleaned ready to go on

http://img.tapatalk.com/d/13/03/30/y2ymebe2.jpg

[PHO]

Shiiieeeet. I want dem rx pedals.

[Tamagochi]

That double din looks sick!, Make a DIY installation thread so i can get one aswell :D

[dorikin]

Butch to install
http://img.tapatalk.com/d/13/03/31/2ubutyra.jpg

[Spoon-Accord]

I remote started my car into my tree in front of the house. Fml got a new patch of missing paint now

[mattsrea]

LOL! Fail! Why did you remote start it? haha

[ivseenwars]

Having a lot of trouble selling the EK.. considered pulling it off sites and doing another respray + motor swap.

[EKVTIR-T]

Having a lot of trouble selling the EK.. considered pulling it off sites and doing another respray + motor swap.What are you going for next?

Something turbo?

[PHO]

d15bR

[grifty]

Having a lot of trouble selling the EK.. considered pulling it off sites and doing another respray + motor swap.

Too many lowballers?

[PHO]

Too many lowballers?

Too many high rollas.

[ivseenwars]

Too many lowballers?
"Would you sell it for $2000?"
"no"
"what about $2350"
"no"
"wtf how much do you want man"

literal conversation.


What are you going for next?

Something turbo?

Was going for a DC2. CBF with turbo

[EKVTIR-T]

Was going for a DC2. CBF with turbo
ugh.............

[ivseenwars]

ugh.............

lol what

[PHO]

lol what

c2 so boring

[ivseenwars]

c2 so boring

hense why i considered just swapping something into the EK

[ctx]

hense why i considered just swapping something into the EK

As a lot of people have kept saying..you've come this far, why abandon it now?

[ivseenwars]

As a lot of people have kept saying..you've come this far, why abandon it now?

yeah im keeping it lol

feel like a kid in a candy store atm though
https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash4/299120_447698005313652_838104711_n.jpg

[PHO]

AMMO some really good stuff.

[ctx]

yeah im keeping it lol

feel like a kid in a candy store atm though
https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash4/299120_447698005313652_838104711_n.jpg

Holy moly. I want everything in this picture.

[ivseenwars]

Holy moly. I want everything in this picture.

was gonna buy the wheel regimen too but it would've been over $200 lol

[ctx]

was gonna buy the wheel regimen too but it would've been over $200 lol

Must have cost a fair bit still. That's some pro compounds you got there lol.

Please post pics when you detail car with these :D

[ivseenwars]

Must have cost a fair bit still. That's some pro compounds you got there lol.

Please post pics when you detail car with these :D

$165 to my door and a three week wait, spensive and really hope its worth it haha
doing it tomorrow(today), will do haha

[ivseenwars]

After Foam, Hydrate and then skin.
http://farm9.staticflickr.com/8112/8615662068_342a3404e1_c.jpg
Next up coils?

[ekx105]

Soooo cleannnnnn!!! Pm me where you got those cleaning products from :)

[EKVTIR-T]

Soooo cleannnnnn!!! Pm me where you got those cleaning products from :)Use that money to get wing painted

[grifty]

soooo cleannnnnn!!! Pm me where you got those cleaning products from :)

x2...

[simmy]

Hey fellas, any tips on street coilovers? Bang for buck..

But I don't really want something that will knock up in a few months... Open for any opinions

[mocchi]

Hey fellas, any tips on street coilovers? Bang for buck..

But I don't really want something that will knock up in a few months... Open for any opinions

tein ss

[ekx105]

Use that money to get wing painted

Lol true. Money is going towards engine plus full re-spray

[mattsrea]

Lol true. Money is going towards engine plus full re-spray

Full respray? To what colour? Body looks clean as is asides the parts you bought and havent repainted.

[ekx105]

Full respray? To what colour? Body looks clean as is asides the parts you bought and havent repainted.

Ful respray cause got quoted only a couple of hundred $$$ difference between painting bars and wing to painting the whole car. Got mates rates too. Undecided on the colour.
Either keeping it white or something different.. Battleship grey??? Still undecided.

[mattsrea]

Picked up some free tweeters from wreckers the other day and managed to install them :) Really happy of how they sit and how good they are!
http://img96.imageshack.us/img96/8610/20130403145805.jpg

[ivseenwars]

Ful respray cause got quoted only a couple of hundred $$$ difference between painting bars and wing to painting the whole car. Got mates rates too. Undecided on the colour.
Either keeping it white or something different.. Battleship grey??? Still undecided.

Just paint the bars and wing lol. Whoever you're going to is over charging you or is doing dodgy resprays.

[grifty]

Ful respray cause got quoted only a couple of hundred $$$ difference between painting bars and wing to painting the whole car. Got mates rates too. Undecided on the colour.
Either keeping it white or something different.. Battleship grey??? Still undecided.

i would stick with a white imo unless you want to pay extra and have the bay + door jams done.

[mattsrea]

Why change colour man? So many people these days (incl myself) would love a white civic, sadly white ej8s were hard to come by back in my days ><" So yeah stick with white :) And yeah what ivseenwars said is true. Painting a bar and wing shouldn't cost more then $500 and if painting your car for $500 isn't a diy backyard job then its kinda dodgy.

[ivseenwars]

Why change colour man? So many people these days (incl myself) would love a white civic, sadly white ej8s were hard to come by back in my days ><" So yeah stick with white :) And yeah what ivseenwars said is true. Painting a bar and wing shouldn't cost more then $500 and if painting your car for $500 isn't a diy backyard job then its kinda dodgy.

Average price a decent panel shop should be charging you is $850-$1000 for EVERYTHING. (Strip car, prep/repair, paint, assemble, detail) Drive in drive out. Any more and you're getting ripped off.

[mattsrea]

really? I thought that cost would be for a front end only?

DT Panels and MJ Jap Motorsports charge approx $2.5k excl. engine bay and door jam. Dunno about assemble though.

[ivseenwars]

really? I thought that cost would be for a front end only?

DT Panels and MJ Jap Motorsports charge approx $2.5k excl. engine bay and door jam. Dunno about assemble though.

I was talking about just the bars and the wing. And it needs to be a top quality job. Full doors closed respray i'd expect like 2.5-3k. 4K + for jams+bay.

[mattsrea]

oh right fair enough that makes sense then.

[ctx]

After Foam, Hydrate and then skin.
http://farm9.staticflickr.com/8112/8615662068_342a3404e1_c.jpg
Next up coils?

Oh you got your P's. Congrats buddy. No more attending meats on foot.

Also the ammo stuff turned out ridiculously good. How does it feel?

[mocchi]

Average price a decent panel shop should be charging you is $850-$1000 for EVERYTHING. (Strip car, prep/repair, paint, assemble, detail) Drive in drive out. Any more and you're getting ripped off.

lol would like to see you do this work for 850-1k.
strip car, fix/pull and dents, bog it and block sand till straight.
prime then guide coat it.
then buff and detail

shops gotta make money, its a business after all

[EKVTIR-T]

maybes thats in India

http://www.9kracing.com/wp-content/uploads/2012/01/CUUQF.gif

[ivseenwars]

Oh you got your P's. Congrats buddy. No more attending meats on foot.

Also the ammo stuff turned out ridiculously good. How does it feel?

Nah man, I wish. Still on L's for a while. Sisters friend borrowed it and I just hadn't taken the plates off.

As for ammo. I can't stop staring at it haha, its so shiney. But ofc as soon as i finished buffing the skin off it started drizzling :(


lol would like to see you do this work for 850-1k.
strip car, fix/pull and dents, bog it and block sand till straight.
prime then guide coat it.
then buff and detail

shops gotta make money, its a business after all

I do this work daily LOL. I wasn't talking about a whole respray for 850-1k i was talking JUST wing and front/rear bars.

[mocchi]

Nah man, I wish. Still on L's for a while. Sisters friend borrowed it and I just hadn't taken the plates off.

As for ammo. I can't stop staring at it haha, its so shiney. But ofc as soon as i finished buffing the skin off it started drizzling :(



I do this work daily LOL. I wasn't talking about a whole respray for 850-1k i was talking JUST wing and front/rear bars.


when u said strip car, you meant remove front/rear bar from car?
my mistake baboy


http://www.9kracing.com/wp-content/uploads/2012/01/CUUQF.gif

[EKVTIR-T]

thought he meant full strip and respray car

[ivseenwars]

when u said strip car, you meant remove front/rear bar from car?
my mistake baboy


http://www.9kracing.com/wp-content/uploads/2012/01/CUUQF.gif

lol my bad for wording it wrong but yeh meant removing bars and wing.

[mattsrea]

Installed DC2 Maplight, might grab an RD1 maplight or a later civic from wreckers this weekend, but at the moment looks good! And needa get them bright white lights :)

Sorry for dark images
http://img684.imageshack.us/img684/917/20130404164506.jpg
http://img256.imageshack.us/img256/3932/20130404164515.jpg

[EKVTIR-T]

wow good idea

nice work and detail

[PHO]

wow good idea

nice work and detail

[carayan]

Bought Ek T bracket and timing side bracket for epic b18 actionnnnn hnnnnng

[MYEK9]

Got all my new detailing kit, and have been hitting it up hard to get the best results! recently cut / polished / wax the whole car, and detailed the whole interior and trims, very happy with my results

http://i49.tinypic.com/34jdj6o.jpg

[PHO]

Got any direct sun or direct light into lens to show for swirls?

Eg,

After left, before right

http://i302.photobucket.com/albums/nn91/carcareproducts/DSC_0526_1280x850_zpse81f550d.jpg


You using a rotary or randomorbital?

[MYEK9]

No swirls or scratches, i use hand applicator pads, but also have a KEN auto buffer, (buying a meguiars g110v soon) , ive detailed probaly 15-25cars in the last 1 month, all with no swirls and scratches left behind,

I use only meguiars products, even though their expensive.. your left with showroom results, the way i see it, you pay for what you get...

I recently also did fellow friend/member p3akin integra type r , results where astonishing on how well the compound cut worked into the paint and the polish/wax @ the end to finsh of your hard work

the before and after on the pic shows it also . thats just the cut stage , not even polishing and look @ difference


http://i45.tinypic.com/2yzms76.jpg

[MYEK9]

Ive also noticed, ive been using yellow as the main hand applicator pad colour, but for cutting i believe maron/burgandy is defiently the best colour, yellow for polishing / black for waxing.

Here is another customer car, that had swirl marks that bad it was the worst car ive seen so far.

after 2:30 - 3hrs of work.. got it looking like this

http://i49.tinypic.com/29m87ma.jpg

[viinnh]

Bought Ek T bracket and timing side bracket for epic b18 actionnnnn hnnnnng

did you by any chance meet at livo kk's and bought it from a guy with a x3 and car trailer?

[carayan]

did you by any chance meet at livo kk's and bought it from a guy with a x3 and car trailer?

yeah i did actually LOL was that you that came in the mazda6?

[viinnh]

yeah asian passenger lool

[ivseenwars]

Took to the trims with some vinyl n plastic cleaner.
http://img.tapatalk.com/d/13/04/05/6yzyqese.jpg
And the mudflaps.
http://img.tapatalk.com/d/13/04/05/aduvu8em.jpg

[Niko]

Gave the car a quick wax

http://img42.imageshack.us/img42/5963/img1464vk.jpg

[MYEK9]

http://i50.tinypic.com/2dj9wsh.jpg

Detailed interior + steam cleaned and protected the recaro's came out awsome!

[atari]

Doing a B-series swap

http://farm9.staticflickr.com/8113/8626483625_df1abf9e90_c.jpg

[ctx]

Ive also noticed, ive been using yellow as the main hand applicator pad colour, but for cutting i believe maron/burgandy is defiently the best colour, yellow for polishing / black for waxing.

Here is another customer car, that had swirl marks that bad it was the worst car ive seen so far.

after 2:30 - 3hrs of work.. got it looking like this

http://i49.tinypic.com/29m87ma.jpg

lolol kennys car. Probably from all the visits to car washes?


Doing a B-series swap

http://farm9.staticflickr.com/8113/8626483625_df1abf9e90_c.jpg

Original engine gave in, or just feel like swapping?

[KennyBKT]

lolol kennys car. Probably from all the visits to car washes?



Paint was already shitty from previous owner haha! I go car wash for the high pressure hose pretty much LOL

[baethos]

So I was test fitting my BBS RS'es today and noticed that the stock lug nuts don't fit properly. They don't seem to seat on the wheel properly and they stick out too much that I can't properly screw down the centre waffle cap. Anyone know what lug nuts I need to use? Thanks.

[EKVTIR-T]

You need tapered for aftermarket wheels,so they seat correctly

see the difference

http://www.f150online.com/forums/members/kingfish51-albums-truck-pics-picture266-lug-nut-types.jpg
http://s21.postimg.org/jus8vwuon/DSC00099.jpg

[hilarryous]

Ive also noticed, ive been using yellow as the main hand applicator pad colour, but for cutting i believe maron/burgandy is defiently the best colour, yellow for polishing / black for waxing.

Here is another customer car, that had swirl marks that bad it was the worst car ive seen so far.

after 2:30 - 3hrs of work.. got it looking like this

http://i49.tinypic.com/29m87ma.jpg

you havent seen my car yet

[MYEK9]

Let me see it haha no jobs to hard , unless your clear coat is peeling like glad wrap

[hilarryous]

Let me see it haha no jobs to hard , unless your clear coat is peeling like glad wrap

You guys are from vic haha. Isn't peeling or fading, but swirls and contaminants are crazy.

[ivseenwars]

Let me see it haha no jobs to hard , unless your clear coat is peeling like glad wrap

thats when the car comes to me lol

[MYEK9]

hahah to funny!

[Niko]

New Monte Carlo 350mm wheel

http://img11.imageshack.us/img11/9606/dscf1877n.jpg

http://img32.imageshack.us/img32/3909/dscf1876f.jpg

[Riced_Civic]

touch up tune ready for nationals

http://i204.photobucket.com/albums/bb278/riced_civic/th_VIDEO0002_zpse2f186cb.jpg (http://i204.photobucket.com/albums/bb278/riced_civic/VIDEO0002_zpse2f186cb.mp4)

[THE 2BSEEN]

Took to the trims with some vinyl n plastic cleaner.
http://img.tapatalk.com/d/13/04/05/6yzyqese.jpg
And the mudflaps.
http://img.tapatalk.com/d/13/04/05/aduvu8em.jpg

Buy some autoglym bumper care gel on your black plastic and rubber trims.
It makes them look spot on for a long time
Really nice stuff

[IEVAQ8]

touch up tune ready for nationals

http://i204.photobucket.com/albums/bb278/riced_civic/th_VIDEO0002_zpse2f186cb.jpg (http://i204.photobucket.com/albums/bb278/riced_civic/VIDEO0002_zpse2f186cb.mp4)

so...

who tunes ur car and how much power u pushing out???

[Alvis]

Haven't posted in a while - hit 80,000kms, washed and swissvaxed car + cleaned engine bay

[iceey]

Installed my ctr lips came alone quite good
http://s1160.photobucket.com/user/xXiceeyXx/media/image-2.jpg.html?sort=3&o=0

[mattsrea]

pics? links broken

[viinnh]

Installed my ctr lips came alone quite good
http://s1160.photobucket.com/user/xXiceeyXx/media/image-2.jpg.html?sort=3&o=0

http://i1160.photobucket.com/albums/q495/xXiceeyXx/image-2.jpg

[MYEK9]

Had a fun 3 days rewiring / neating engine loom + central locking alarm ki
Never want to see another wire again hahaht

[ivseenwars]

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn1/58846_454734877943298_1614154992_n.jpg
Not an update as such but got more AMMO stuff.. lol #imso****ingbroke

[carayan]

changed me guard so no more dented guard action

[ROM30S]

Does anyone know if the stock hatch muffler will fit straight on if the cars fitted with a whiteline rear swaybar which also has the back plate?

[dorikin]

jizz

http://img.tapatalk.com/d/13/04/20/duju2ysu.jpg

[AlexK]

No swirls or scratches, i use hand applicator pads, but also have a KEN auto buffer, (buying a meguiars g110v soon) , ive detailed probaly 15-25cars in the last 1 month, all with no swirls and scratches left behind,

I use only meguiars products, even though their expensive.. your left with showroom results, the way i see it, you pay for what you get...

I recently also did fellow friend/member p3akin integra type r , results where astonishing on how well the compound cut worked into the paint and the polish/wax @ the end to finsh of your hard work

the before and after on the pic shows it also . thats just the cut stage , not even polishing and look @ difference


http://i45.tinypic.com/2yzms76.jpg

I hope your clay baring that surface.. ..before you work..

You are doing a great job ! , How Ever, im finding it almost near impossible to believe that you are removing swirls and scratches by hand. Please dont be offended im just amazed, also you should use a SUNLIGHT when cutting and buffing becasue to the eye you will never see it.. Products like meguiars are almost like fillers, it gives the look that there gone but really there not. after a couple of washes your back to wear you started.

Biggest offender of this is AUTO GLYM Super Resin Polish.

Also meguiars products are not the cream of the crop.. you can buy much much better at almost tripple the cost, but like you said you get what u pay for..

If you have never used a rotary before then maby as mentioned above use a random orbital buffer less chance of burning through, i use a paint gauge when cutting and buffing, worth the money..

Please don't take this the wrong way, u are doing a great job, but i have buffed ALOT of cars, and there is alot that goes into making a show car finish.. It took me 30 hours to cutt and rotary buff my car only, not including the time i took to wash it 3 times during that process..

How ever i can tell the diffence and it looks good :)

[PHO]

rawrrrrrrrrrrrr

I'm with this guy. Ever since I heard about that kenny dude getting a "cut and polish" from you, and to hear you were just claying and using a glaze via hand. You may be hiding a minute number of swirls. But definitely not a cut and polish. But if the paint is actually already in good condition, and you're just decontaminating it and chucking on some nuba wax for some short term protection. Good on ya.
Hence why I also asked for direct light into lens (via panel) or shots in sunlight. But if the clients are happy, good job!

I do recommend starting with a DA/RO like AlexK said (have an orbital path, very hard to heat up the paint, therefore very good for newbies so you dont burn through the paint). Get some good pads (festool/lakecountry ect), good compounds like Merzena (personal favourite). Read some guides on the net (or attend a hands on day with one of our traders, Car Care Products) and get started!

Finish of with some good quality waxes/sealants to protect your work.


edit. If you're not claying, you should punch yourself in the balls, you are effectively ruining people's paint by dragging along dirt and marring the paint.

But if you are, good on ya. I suggest some ClayMagic :]]

[CivicEGSI]

flame warrrrrrr

[PHO]

flame warrrrrrr

Mateeeee. You dont belong here.

[AlexK]

I'm with this guy. Ever since I heard about that kenny dude getting a "cut and polish" from you, and to hear you were just claying and using a glaze via hand. You may be hiding a minute number of swirls. But definitely not a cut and polish. But if the paint is actually already in good condition, and you're just decontaminating it and chucking on some nuba wax for some short term protection. Good on ya.
Hence why I also asked for direct light into lens (via panel) or shots in sunlight. But if the clients are happy, good job!

I do recommend starting with a DA/RO like AlexK said (have an orbital path, very hard to heat up the paint, therefore very good for newbies so you dont burn through the paint). Get some good pads (festool/lakecountry ect), good compounds like Merzena (personal favourite). Read some guides on the net (or attend a hands on day with one of our traders, Car Care Products) and get started!

Finish of with some good quality waxes/sealants to protect your work.


edit. If you're not claying, you should punch yourself in the balls, you are effectively ruining people's paint by dragging along dirt and marring the paint.

But if you are, good on ya. I suggest some ClayMagic :]]


flame warrrrrrr

Lol at that rawrr haha, i see u have the same process as my swelf but i got
Dodo clay, ahh the ball breaking stage of menzerna 500.......

You sir, are correct in every sentance.

And its not a war just contructive fees back

[nobbs]

Gave it a quick wash and topped up my fluids yesterday... then this morning it was raining!

http://imageshack.us/a/img32/6213/image1366600975486739.jpg

[THE 2BSEEN]

Ive been meaning to take my ek to the paint shop.

Im guna get there.......

[edmondvincent]

Got my adjustable springs in today (on a uni budget cant afford coilovers :[ ... ) and got my grille in to replace the diy one that I did about a year back, looked alright but decided to get a nicer looking one, thing didnt want to fit on so ill get the grinder out tomorrow and work it out! Also got to get that disgusting scratch buffed out of the bumper, too many things to do -.-

http://i34.tinypic.com/6oifxg.jpg

[CivicEGSI]

Mateeeee. You dont belong here.

I could say the same, mate.

[ctx]

Got my adjustable springs in today (on a uni budget cant afford coilovers :[ ... ) and got my grille in to replace the diy one that I did about a year back, looked alright but decided to get a nicer looking one, thing didnt want to fit on so ill get the grinder out tomorrow and work it out! Also got to get that disgusting scratch buffed out of the bumper, too many things to do -.-

http://i34.tinypic.com/6oifxg.jpg

Nice car, very shiny

[Rayseuro04]

Fitted a new skunk 2 intake manifold, S90 throttle body, new hondata S300 and works engineering FPR and fuel rail to my B20....
http://i1260.photobucket.com/albums/ii580/rays2701/010-3_zps2a3e9021.jpg
http://i1260.photobucket.com/albums/ii580/rays2701/009-4_zps1d1d2a8b.jpg
http://i1260.photobucket.com/albums/ii580/rays2701/008-3_zps392de476.jpg

[mattsrea]

Clean engine bay dude!

[THE 2BSEEN]

That's a nice bay bro.

You take pride and do your own thing.

It's easy to put a engine together harder to keep it like this

[MYEK9]

I'm with this guy. Ever since I heard about that kenny dude getting a "cut and polish" from you, and to hear you were just claying and using a glaze via hand. You may be hiding a minute number of swirls. But definitely not a cut and polish. But if the paint is actually already in good condition, and you're just decontaminating it and chucking on some nuba wax for some short term protection. Good on ya.
Hence why I also asked for direct light into lens (via panel) or shots in sunlight. But if the clients are happy, good job!

I do recommend starting with a DA/RO like AlexK said (have an orbital path, very hard to heat up the paint, therefore very good for newbies so you dont burn through the paint). Get some good pads (festool/lakecountry ect), good compounds like Merzena (personal favourite). Read some guides on the net (or attend a hands on day with one of our traders, Car Care Products) and get started!

Finish of with some good quality waxes/sealants to protect your work.


edit. If you're not claying, you should punch yourself in the balls, you are effectively ruining people's paint by dragging along dirt and marring the paint.

But if you are, good on ya. I suggest some ClayMagic :]]

Dude I got a very good buffer with meguiars soft buff pads , I use the buffer always but use hand also In hard to reach places, kenny car paint was not in good condition at all , we used the buffer on 90% of the cars with the scratchx also .. My results are 100% doing this , since I have done over 25-30 customer cars range from prestige to jap .. Clay bar most of the time is not needed due to the special design of pad I use which also removes most of the grime while cutting ,

[MYEK9]

And I never clay'd Kenny car also , so do not know where you heard that from

[MYEK9]

This is the latest edition of the c and p , " PHO"

[ctx]

This is the latest edition of the c and p , " PHO"

Before and after shots mate?

[KennyBKT]

http://i480.photobucket.com/albums/rr161/kenneth_tan13/DSC_1339.jpg (http://s480.photobucket.com/user/kenneth_tan13/media/DSC_1339.jpg.html)
Got my hands on an OEM access rear lip! More to come

[mattsrea]

Heard the access lip isnt a direct fit for them faceift rear bars because of that kink at the bottom, let me know how it fits!

[KennyBKT]

^will do! seen them work on facelift rear bars tho

[AlexK]

Before and after shots mate?

+1, With a SUNLIGHT ! :)

[ivseenwars]

+1, With a SUNLIGHT ! :)

+1 "A good buffer and a meguiars soft pad". Need more info than that man. What pad? Polishing pad? Cutting pad? Microfibre? Wool? Methods? How long are you spending on each panel? Before & After shots in sunlight or with a sungun would prove your results.

[MYEK9]

got to get them off my camera got a few before and afters, and in direct sunlight also.. i find that ken 7'' wool pad detiorates to quickly , so ive switched to the Meguiars 2.0 soft buff burgandy pad, works very well , smooth and does not affect the paint (burn), i also use the meguiars 2.0 7'' soft buff polisher pad ( yellow ) when polishing and the black colour basic pad when waxing, all up roughly around 2:30 -3hrs a car depending on condition even longer.

[MYEK9]

also a good product is that tech wax 2.0 , expensive as fk but works very well . im looking for a good trim cleaner though to brighten up the black trims around the car ( door frame , roof lining ? you know any

[ivseenwars]

also a good product is that tech wax 2.0 , expensive as fk but works very well . im looking for a good trim cleaner though to brighten up the black trims around the car ( door frame , roof lining ? you know any

Autoglym trim restorer, forever black, etc. just plastic/vinyl restores do well.

Seems like you've got a good setup, although I prefer hand waxing/sealing. How often do you find yourself wet sanding?

[CivicEGSI]

introducing



***Official how did you buff your EK today***

[PHO]

introducing



***Official how did you buff your EK today***

Do u even buff johnny tran?

[CivicEGSI]

Do u even buff johnny tran?

u wot m8

[THE 2BSEEN]

So my ek goes to get its front bar repainted on tuesday

[baethos]

Installed my buddy club n+ coilovers today. Anyway, I have a question for you guys. With the rear coilovers, where the shock bolts to the lower control arm...I assume I need a nut right? At the moment I just hammered the bolt through. On the oem shocks, there is a nut but it seems to be welded to the shock fork - lol? I didn't get any nuts with this suspension (bought 2nd hand). I know sounds like a dumb question, but just wanted to be sure. Thanks.

[dorikin]

Nek minnit ridin on rails

[grifty]

Installed my buddy club n+ coilovers today. Anyway, I have a question for you guys. With the rear coilovers, where the shock bolts to the lower control arm...I assume I need a nut right? At the moment I just hammered the bolt through. On the oem shocks, there is a nut but it seems to be welded to the shock fork - lol? I didn't get any nuts with this suspension (bought 2nd hand). I know sounds like a dumb question, but just wanted to be sure. Thanks.

yes you do need a nut.....

[CivicEGSI]

please use a nut or you will die lol

[baethos]

haha ok. anyway, can someone please tell me what sized nut to get? an M10 or 12mm nut does not fit. The M10 nut screws on for about 5mm, then gets stuck. The 12mm nut is too big. What sized nut and where can I find it? Thanks!

[mattsrea]

12x1.5 is the size. And where can you find it? Almost anywhere? ebay?

[baethos]

^ errr really? I have M12x1.5 lug nuts for my wheels. Just checked and these nuts are too big for the bolts (that joins lca to shock).

[baethos]

Anyway, I found this link to buy bolts + nuts.

http://www.ebay.com/itm/3-x-HONDA-REAR-LOWER-CONTROL-ARM-BOLT-LCA-CIVIC-SUSPENSION-COILOVER-EK9-VTI-ITR-/200915492484?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item2ec77f1e84

Another question. I am installing an ASR subframe brace and beaks bar. Does anyone know the specific bolt that I need to secure the beaks bar, asr subframe bar and lca together?

Thanks

[baethos]

Are these the correct bolts for the subframe brace and beaks bar?

http://www.clubcivic.com/board/showthread.php?t=219222

10x1.25 with class 10.9?

[mattsrea]

oh wait i thought you were talking about lug nut for wheel lol. My bad. Not sure on them

[CivicEGSI]

Asr comes with bolts pretty sure. Also why you want beaks bar? Do you like buying parts that only serve a purpose of getting ruined from scrape? Trying to build a hardparker? IMO most pointless thing out.

[PHO]

Asr comes with bolts pretty sure. Also why you want beaks bar? Do you like buying parts that only serve a purpose of getting ruined from scrape? Trying to build a hardparker? IMO most pointless thing out.

F7 yeeeeeeee

[ctx]

Anyway, I found this link to buy bolts + nuts.

http://www.ebay.com/itm/3-x-HONDA-REAR-LOWER-CONTROL-ARM-BOLT-LCA-CIVIC-SUSPENSION-COILOVER-EK9-VTI-ITR-/200915492484?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item2ec77f1e84

Another question. I am installing an ASR subframe brace and beaks bar. Does anyone know the specific bolt that I need to secure the beaks bar, asr subframe bar and lca together?

Thanks

http://www.jdmyard.com/image/cache/data/beaks/3760969309_503f5bf926-250x250.jpg

http://www.rodneyolsen.net/wp-content/blogger/wheelie_bin.gif

http://png-3.vector.me/files/images/1/5/158677/doctormo_put_rubbish_in_bin_signs_clip_art_thumb.j pg

http://www.derbyshirescoutclimbing.co.uk/wp-content/uploads/tick-150x150.png

[baethos]

lol. I mod the car the way I like it. Don't care what others think. Just looking for some answers...

[ctx]

lol. I mod the car the way I like it. Don't care what others think. Just looking for some answers...

you can keep beaks bar in car for hit criminal instead

http://i.imgur.com/scC3fkv.jpg

[baethos]

good idea. i think i'll buy a 2nd one for that.

[ctx]

good idea. i think i'll buy a 2nd one for that.

no

use the one you already have. because it is useless on your car

[viinnh]

why dont you just bring that bolt to the local auto shop and buy the right bolt for it? make sure its hi tensile

[CivicEGSI]

good idea. i think i'll buy a 2nd one for that.

Maybe you should buy a third one to beat off all the sluts that your car will attract cause it looks so badass with that beaks bar and all of your sw@g xD xD xD

[baethos]

haha. beaks bars seem to pinch on a lot of ppl's nerves. love it! hahaha

[mattsrea]

lol beaks bars are ok if your cars stanced haha. I'm trying to get rid of mine, scraping my driveway everytime because its hellah steep.

[ctx]

haha. beaks bars seem to pinch on a lot of ppl's nerves. love it! hahaha

no, the end of your rear appear to be in pain

[SHOGUNOVDDRK]

no, the end of your rear appear to be in pain

Like a sir.

[baethos]

no, the end of your rear appear to be in pain

u seem mad bro

[ctx]

u seem mad bro

you seem unhappy people think beaks bar is a joke mod to put on honda car

did u make sure to buy a red one for more racing style?

[baethos]

nope. i'm used to it. you must be a function > form guy I'm guessing?

[viinnh]

whats wrong with a beaks bar, i did 1:25 at wakefield with out a beaks bar. added it on got 1:15.

[ctx]

nope. i'm used to it. you must be a function > form guy I'm guessing?

the form is in the function

[viinnh]

the form is in the function

but the function is in the form

[ctx]

but the function is in the form

i dont see the function in 165 tyre on 8" wheel

[EKVTIR-T]

i dont see the function in 165 tyre on 8" wheelFuel economy

[SHOGUNOVDDRK]

Fuel economy

Leaded fuel replacement brah

[viinnh]

i dont see the function in 165 tyre on 8" wheel

makes the form of the wheel function

[Tosies]

whats wrong with a beaks bar, i did 1:25 at wakefield with out a beaks bar. added it on got 1:15.

srs? **** i should get one on asap!

[ctx]

srs? **** i should get one on asap!

it must be the aircraft grade aluminium shaving seconds off laptimes

[baethos]

^ For ctx haha...finally got the right bolts and beaks bar is on!

24665

[PHO]

Buys an ASR subframe reinforcement. Doesn't even have rear sway bar. GG.

[ctx]

^ For ctx haha...finally got the right bolts and beaks bar is on!

24665

what are you using asr subframe reinforcement for when no swaybar to reinforce? perhaps reinforcing Honda boy racer stereotype instead?

[dr1ftaX]

^ For ctx haha...finally got the right bolts and beaks bar is on!

24665

You just went full retard.

[Tosies]

You just went full retard.
Agreed.

[viinnh]

^ For ctx haha...finally got the right bolts and beaks bar is on!

24665

is that the replica one tiksie selling?