***Official What did you do to your Integra today***

[Goku]

finally got my ozhonda sticker :) stuck that on and im lovin it.

[EKVTIR-T]

finally got my ozhonda sticker :) stuck that on and im lovin it.
pics of sticker stucked smoothly

[DCZ 18C]

Ill never understand why people wanna pay that much and go through the trouble of opening the lights up when you can just drill holes for free in 10 minutes.

Because drilling a whole
Doesn't prevent water from getting in your car.. And drilling a hole is not a preventative.. Just hides the prOblem .. Which will Most likely come Back to bite you In the ass when the cOnstant moisture behind your tail lights starts to cause rust that will
Not be visible and cause damage in the long term.

Goodluck with that Charliebrown.

[EKVTIR-T]

When my roof in my house leaks I drill a hole in the floor,then the water runs through and outside again...

[Lukey]

buy the gaskets from america, $25ea instead of $50ea here in aus

i have part numbers if needed

[eLtrix]

Tried taking our my door glass... to no avail? Any tips? I took out the bolts that was holding the glass in place, but i cant slide it out at all

[tripleuse]

When my roof in my house leaks I drill a hole in the floor,then the water runs through and outside again...

fkn LOL!

[Setanta]

Replacement radiator cap. I'd replaced the 1.3 Cusco with a 1.3 Mugen as I had a little coolant collecting on the fan shrouds under the filler - wasn't hoses. I noticed that neither was a good fit, instead of lining up parallel to the radiator when on, they twisted a little further. Bought a 1.0 genuine Honda one and noticed the grips were about 2mm longer. fingers crossed it was just dodgy non-OEM. Opened up my air-box - time for a new filter. It's ducted to the lower grille rather than using the factory resonator setup - I need to run some coarse mesh over the inlet pipe I think :)

300 bucks worth of E30 parts arrived for the BMW from the US (cheaper buying and shipping than buying in Aust) on Friday - sadly I won't have much time to play with either car for a few weeks as I have a 2 day conference coming up followed by HSC prac marking which kills my weekends.

[ricciardi80]

Went for a nice sunday drive through the hills with a friend in his GTI.
This is my first Honda. so im new to all this.
Stock standard DC4 btw, only bought it last week, been very happy with it so far.

http://i49.tinypic.com/2zjg9av.jpg

http://i49.tinypic.com/4sjtjp.jpg

[Latino CRX]

ED / DA Arm rest .. FINALLY .. pick it up in day or 2 :)

[Lukey]

put my engine in. still got alot to go. i got avid racing torque mounts, which have been fine. and i also bought avid racing 75a or whatever engine mounts and they seem to make the engine notsit as straight as the oem mounts

http://a1.sphotos.ak.fbcdn.net/hphotos-ak-prn1/546567_10152015706390696_431591013_n.jpg

[dc2r-0636]

Is that a snail ?

[Goku]

need a new paint job badly!!!!!!!!!!!!!!!!

[GSi_PSi]

put my engine in. still got alot to go. i got avid racing torque mounts, which have been fine. and i also bought avid racing 75a or whatever engine mounts and they seem to make the engine notsit as straight as the oem mounts

[IMG]http://a1.sphotos.ak.fbcdn.net/hphotos-ak-prn1/546567_10152015706390696_431591013_n.jpg[/IMG

shieeeeeeeeeeet

i see turbo manifold and a screamer pipe......i think... lol


inb4 vtec head aswell...

[Lukey]

Is that a snail ?

will be on shortly.


shieeeeeeeeeeet

i see turbo manifold and a screamer pipe......i think... lol


inb4 vtec head aswell...

that you do.

no.

[EKVTIR-T]

http://www.epa.vic.gov.au/~/media/System/EPA/Images/logo_epa_62x62.png

[Lukey]

http://www.epa.vic.gov.au/~/media/System/EPA/Images/logo_epa_62x62.png

lols.

[Vvvtec]

nice stuff lukey

lolwut finally getting some balls lol

wut

[Latino CRX]

Arm rest all fitted :)
http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0437.jpg
http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0436.jpg

[45SET]

Sold it...

Sigh...

[tripleuse]

Sold it...

Sigh...

suprised you sold it, was very clean! how much did u end up letting it go for?

[Latino CRX]

Just got the tuning and diagnostic program

[45SET]

suprised you sold it, was very clean! how much did u end up letting it go for?

So am I actually... as I didn't really want to do it... and the new owner could tell I didn't want to let it go, but had to due to my current position.

I sold the car and original engine for very close to the asking price - Which was obviously why I let it go. I'm not going to comment on exact prices, as the new owner is a member on this forum. But it'll more then likely still get about.

[tripleuse]

thats not to bad then,its a shame however!

[SHOGUNOVDDRK]

Sold it...

Sigh...

I'll remember your car as the car Sydney couldn't produce when I first layed my eyes on it.

Arm rest looks good, I'm glad it's gone to worthiness.

[Latino CRX]

Arm rest looks good, I'm glad it's gone to worthiness.

:) thanks again bruzz .. Will come and chill back over soons .. I just couldnt resist a good wingsuit flying day thats all ..
had another good fly this afternoon weather was perfect :)

[Latino CRX]

Just done custom job eye lids on the DA to see what it look like i got a pic i will post it up later

[Latino CRX]

it was only a 5 minute job .. for a yay or nay ...

http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0449.jpg

[89lude]

shaved and painted bay :)

http://i1110.photobucket.com/albums/h445/an-tho-mi/yellow.jpg

[tripleuse]

shaved and painted bay :)

http://i1110.photobucket.com/albums/h445/an-tho-mi/yellow.jpg

****ing 89lude always showing us up! hahaha

[89lude]

haha hardly showing anyone up bro. just trying to share the teg love! :)

[tripleuse]

haha hardly showing anyone up bro. just trying to share the teg love! :)

**** you... looking good man, i wish i had the patience to shave my bay and respray. :(

[EKVTIR-T]

why did you paint it yellow 89

[89lude]

took weeks to do, but don't be discouraged, the hard work pays off! only took us so long because along the way i decided to shave more and more things to a point where i have pretty much 98% of visible holes welded and smoothened out! my hands also fell off with the amount of grinding and sanding :P

[89lude]

and to ekvtir i went yellow because i had yellow paint that i bought for my old teg in the shed lol. must salvage every dollar! :) plus my car is really dark with everything being black wanted to give it some life

[EKVTIR-T]

ah ok,makes sense lol

what colour is the motor and shit gonna be? something to pop off the yellow aye

[89lude]

idk atm. probably something pretty subtle. the yellow bay is enough colour for my liking

[Super-DA9]

black and yellow hazard stripes on the valve cover.

do it!

[93Integra]

http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash3/s720x720/545975_10151044514522098_965658729_n.jpg

http://a1.sphotos.ak.fbcdn.net/hphotos-ak-ash3/524512_10151044513572098_490526712_n.jpg

These arrived earlier :D

[Killa From Manila]

started my wire tuck

harness before
http://i.imgur.com/YAIe6.jpg

stripped and labelled
http://i.imgur.com/uOeOd.jpg

part of the charge harness before
http://i.imgur.com/7hTdw.jpg

after sleeving
http://i.imgur.com/xNuCk.jpg

[dorikin]

hotness

[tripleuse]

started my wire tuck

harness before
http://i.imgur.com/YAIe6.jpg

stripped and labelled
http://i.imgur.com/uOeOd.jpg

part of the charge harness before
http://i.imgur.com/7hTdw.jpg

after sleeving
http://i.imgur.com/xNuCk.jpg

big job, i wish i had the patience! goodluck!

[na-118]

where can i buy the sleeving ?


thank-you





started my wire tuck

harness before
http://i.imgur.com/YAIe6.jpg

stripped and labelled
http://i.imgur.com/uOeOd.jpg

part of the charge harness before
http://i.imgur.com/7hTdw.jpg

after sleeving
http://i.imgur.com/xNuCk.jpg

[Killa From Manila]

where can i buy the sleeving ?


thank-you

browsed this guys store on ebay to choose what colour and kind of sleeving i wanted Furryletters ebay (http://stores.ebay.com.au/FURRYLETTERS/_i.html?_nkw=sleeving&submit=Search&_sid=481644496)

but emailed him to order directly. dmiller108@comcast.net

his direct prices are very cheap and shipping costs next to nothing from the US and only took 2 weeks.

bought this kit of adhesive heatshrink (http://www.ebay.com.au/itm/180837987736?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649) from ebay

and to de-pin the plugs just a $3 set of tiny screw drivers from a hardware shop

[90LAN]

looks great

[Goku]

hey guys just need a quick opinion, ive got a bit of paint fade on the bonnet, roof and boot. but the ones on the roof and boot arent that noticeable, should i go for a hood respray or just do a carbon fibre wrap? i know it might not look real but im still a student in year 12 only working 1-2 shifts. so i dont earn a lot. saving up might be an option but its going to take a long time. hahha. cheers

[Dubstein]

hey guys just need a quick opinion, ive got a bit of paint fade on the bonnet, roof and boot. but the ones on the roof and boot arent that noticeable, should i go for a hood respray or just do a carbon fibre wrap? i know it might not look real but im still a student in year 12 only working 1-2 shifts. so i dont earn a lot. saving up might be an option but its going to take a long time. hahha. cheers

How bad is it? Throw up some pictures man

[cbauto]

nice harness......

soupss ozhonda

[Goku]

How bad is it? Throw up some pictures man

sure thing. the weather is just horrible atm. once i can get a day where its a bit sunny i definately will. as long as there is no sunlight directly hitting the bonnet, u cant really tell but once u go up close u sorta can tell.

[winsto_zuki]

I installed ultra racing front strut brace as well as the c-pillar one too. And replaced my k&n pod with a new pod because my one is super dirty...was like that when i bought the car. Might try cleaning the k&n one after seeing how this one goes!
http://i103.photobucket.com/albums/m138/winsto_zuki/1346901402305.jpg

[winsto_zuki]

I was looking to DIY valve engine cover to blue
and also make that light blue intake pipe black, and if not black I would make it silver?
Any ideas/suggestions? :)

[Tuan94]

I was looking to DIY valve engine cover to blue
and also make that light blue intake pipe black, and if not black I would make it silver?
Any ideas/suggestions? :)

Hey man, I used duplicolour to get mine blue. Works wonders, just the price tag is a bit up there, but well spent IMO.
http://img844.imageshack.us/img844/267/blueds.jpg

[202690]

Hey man, I used duplicolour to get mine blue. Works wonders, just the price tag is a bit up there, but well spent IMO.
http://img844.imageshack.us/img844/267/blueds.jpg

looks good andrew!

[winsto_zuki]

Nice!

[bronson11]

Tax came today! So I wen't a little crazy.

The list of things i've purchased over the last couple of weeks looks a little like this:

- Acura Fog Lights
- SPC Camber Kit
- Ground Control Coilover for my existing koni yellows
- Decided to replace the old and worn bushes in my car, so i bought a full hardrace kit.
- Finally found a good condition set of rears to compliment my 5 stud conversion (already had the fronts).
- DC2R momo Steering wheel
- HEL Braided brake lines
- Slotted Rotors

[dorikin]

Cleaned intake manifold - can't decide whether to paint it or not

Before clean
http://img51.imageshack.us/img51/4462/img4145o.jpg

After clean
http://img407.imageshack.us/img407/2027/img4156e.jpg

[DTN]

i rckon some metal polish might get those black marks out

[eLtrix]

Hey man, I used duplicolour to get mine blue. Works wonders, just the price tag is a bit up there, but well spent IMO.
http://img844.imageshack.us/img844/267/blueds.jpg

That blue is ****ing sexy. Want something like that for mine. Where did you pick up the paint from? The color code?

[viinnh]

Its from super cheap mate

[Latino CRX]

Got some CF-48s yesterday soo just been trying to clean them up and finding a place
that does decent price on tyres ..
http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0467.jpg
http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0465.jpg
http://i1253.photobucket.com/albums/hh590/basejumper1985/Photo0466.jpg

[FoodTray]

^ needs original center caps though! they aren't 15's are they?

[Latino CRX]

na 14's and yeh i will try and find the centers .. i got them for $100 :)

[Renaissance_x]

Are those Lloyd's old ones?

[Latino CRX]

ahaha yeh mate him and dazz came up yesterday

[Tuan94]

That blue is ****ing sexy. Want something like that for mine. Where did you pick up the paint from? The color code?

As viinnh said, just pick it up from your local supercheap or autobarn. Look for the duplicolour range and make sure you grab their primer for it :)

[AlexK]

after weeks of back and fourth hassel bought my self a like showroom condtion 2001 DC2R with under 100k km's, bought from non p plater mature owner :) didi at top one did all checks on the car everything was to the dot.. no accident history what so ever.. he told me the engine is 100% exceeding what he was expecting.. in saying that was not the cheapest dc2r on the block but was exacly the year colour model condition that i wanted so i had to pay the price, and that will remain unknown :)

http://img228.imageshack.us/img228/2079/20120823142656copy.png (http://imageshack.us/photo/my-images/228/20120823142656copy.png/)

[rhys.l]

Looks really clean :)

Was it $99 999? Haha http://www.carsales.com.au/private/details/honda-integra-2001-12970679?base=1216&vertical=Car&cr=5&eapi=2&__N=1246+1247+1252+1282+4294965322+4294965105+898+ 1216&num=15&silo=Stock&Range=Year:2001,2001&sort=default

[AlexK]

hahahahaha not far off ;) but nah obviously not that much.but i.was open to.a.wide.selection of dc5rs and ep's

[DTN]

Were yu at byp on sunday?

[AlexK]

if ur talking to me then no i wasnt never been there lol

[Dubstein]

Looks mint! Plans?

[dc2r-0636]

I remember when mine looked like that 4x4 spec lol
Looks clean!

[dc2r-0636]

needs a wash
http://i1211.photobucket.com/albums/cc426/daniel_b18c7/IMG_1325.jpg

[dc2screama]

needs a wash
http://i1211.photobucket.com/albums/cc426/daniel_b18c7/IMG_1325.jpg

Keon gym?:p

[dc2r-0636]

Yes :)

[dc2screama]

Lol Cars looking nice and low, what sussy you got happening man?

[dc2r-0636]

Cheers bro! I got BC racing (br series) coilovers

[Killa From Manila]

Finally got some time to finish off my engine harness.
Now just need cable and some lugs to finish off the charge harness

http://i.imgur.com/ZSdp8.jpg

http://i.imgur.com/yvqNE.jpg

http://i.imgur.com/Uthhl.jpg

[viinnh]

OEM clutch master not even 2 months ****ed up. leaking with in 1 month, completely ****ed in less then 2. ****ing wasted money on OEM and this shit happens.
Bought a OEM clutch master was faulty from factory, swapped for another brand new one and that happens ^^^

[dorikin]

How much u spend all up to wrap that harness?

[Killa From Manila]

About $120 including buying a soldering iron and a heat gun

[mocchi]

what happened with the rubber cap for oil sensor m8
did you cut it off lol
awesome work yeah byuddy

[Killa From Manila]

Lol I put it on after I took the photo

[eLtrix]

Finally got some tein flex coil overs put on :D

[White Noise]

Done nothing to my ITR except drive her through the bends on a short detour to work this morning.

Just joined the site so hi to everyone :) Check out my DC5R in the gallery if you would like. Criticisms welcome :)

[Dubstein]

Welcome!

[White Noise]

Thanks :)

[Setanta]

Bounced off the rev limiter when I missed a change. Not happy :S

[Lukey]

got mine running

[Super-DA9]

Bounced off the rev limiter when I missed a change. Not happy :S

Well if it helps look at it this way, the rev limiter is there for a reason, to protect your engine if that happens. and it did it's job :)

[Super-DA9]

got mine running

Nice!

tuned for the snail yet?

[Lukey]

Nice!

tuned for the snail yet?

nah snail isnt on yet

couldnt get it done in time for performance car mania so ive just put stock manidold, etc. back on

started it up for first time tonight.

[Lukey]

http://www.facebook.com/photo.php?v=10152089903520696

[Dubstein]

http://www.ozhonda.com/forum/showthread.php?168170-Resprayed-white-97-GSI-Integra-with-Rego-Stock-and-Clean!

[CivicEGSI]

Nice Lukey, sounds healthy!

[Lukey]

i was suprised at how well/healthy the engine sounded

[CivicEGSI]

When's that boost going on? :P

[Lukey]

soon i hope

[CivicEGSI]

bulk pics fo sho

Also who the **** lives in inala with a teg there are like 8 in my ****ing suburb, ***** you gonn get robbed

[Super-DA9]

http://www.facebook.com/photo.php?v=10152089903520696

Congrats man!! glad to see it worked out :)


http://www.ozhonda.com/forum/showthread.php?168170-Resprayed-white-97-GSI-Integra-with-Rego-Stock-and-Clean!

Why you selling? maaan your DC4 is so clean! :O

[dc2screama]

Any one no what the plug is under the drivers seat?
Srs?
Just wanted to get all seats out and clean it all up.
Cheers

[Super-DA9]

it is for the seatbelt sensor. it throws a light and beeps if the seatbelt is not buckled in

[newpaddy3]

it is for the seatbelt sensor. it throws a light and beeps if the seatbelt is not buckled in

Yeah that. Was so ****ing annoying. Disconnected it first day I got it.

[bronson11]

Today i sprayed my windscreen wipers... they were getting a bit faded and old!

[Dubstein]

Why you selling? maaan your DC4 is so clean! :O

I want another project haha

[CivicEGSI]

I want another project haha

+1

You must spread some Reputation around before giving it to Dubstein again.

[Dubstein]

+1

You must spread some Reputation around before giving it to Dubstein again.

Love you. I will not stop until every car has been resprayed

[CivicEGSI]

****ing lold hard

[dc2screama]

it is for the seatbelt sensor. it throws a light and beeps if the seatbelt is not buckled in

Cheers mate

[dc2screama]

Anyone know if there's any types
Of hood bra for facelifted tegs..

[Setanta]

There is - I got one with mine when I bought it. I think the PO used it once though and I've never put it on the car.

[dc2screama]

There is - I got one with mine when I bought it. I think the PO used it once though and I've never put it on the car.

Got any pics champ?

[Cartoon]

Installed new door and windows seals on my car over the weekend :)

[Lukey]

new copper spark plugs

[dc2screama]

new copper spark plugs

There better then the iridiums?

[Killa From Manila]

Took my car for a drive for the 1st time in a few months, fak its loud lol especially with a hunting idle

[viinnh]

http://sphotos-b.ak.fbcdn.net/hphotos-ak-ash4/420797_4169502609427_58196076_n.jpg

got my fitment perfect but then when i drove around it was scraping, looked under the car ...

http://sphotos-g.ak.fbcdn.net/hphotos-ak-ash3/546328_4170583636452_1257508099_n.jpg

[Vvvtec]

lolwut

[Goku]

http://www.ozhonda.com/forum/showthread.php?168170-Resprayed-white-97-GSI-Integra-with-Rego-Stock-and-Clean!

hey man, how much did the respray cost you?

[Super-DA9]

hey man, how much did the respray cost you?

He did it himself

[Dubstein]

^ Paint and everything else was about $1000

[nate92]

Got my front lip back from the painters and re installed it today, looks back to normal :)
http://i295.photobucket.com/albums/mm159/fineoner/E8553660-3E76-4348-A38D-2B8D56FBF7FD-9883-000007BDF9CB5646_zpsc21fef40.jpghttp://i295.photobucket.com/albums/mm159/fineoner/0E120AE7-0F14-49BE-853B-D936B7EFC04B-9883-000007BE059D7B00_zps7804f569.jpg

[Super-DA9]

Got my front lip back from the painters and re installed it today, looks back to normal :)
http://i295.photobucket.com/albums/mm159/fineoner/E8553660-3E76-4348-A38D-2B8D56FBF7FD-9883-000007BDF9CB5646_zpsc21fef40.jpghttp://i295.photobucket.com/albums/mm159/fineoner/0E120AE7-0F14-49BE-853B-D936B7EFC04B-9883-000007BE059D7B00_zps7804f569.jpg

Car's looking great man!

[nate92]

Car's looking great man!

Thanks man :) few more things to go! And then just the engine to do :)

[eLtrix]

I died a little inside today when i walked to my car this morning to find a beautiful dent on the rear quarter panel and bumper. ****ing hit and runs

[nate92]

farkkk shiet go man! unlucky :(

i cleaned the engine bay and installed my cusco oil catch can today
http://i295.photobucket.com/albums/mm159/fineoner/A83BBB95-1488-4766-9FA0-1E5A91C765F9-11632-000009D90A5846E1_zps36ef6cf2.jpghttp://i295.photobucket.com/albums/mm159/fineoner/A3DE86E0-D26F-4BA7-8913-9F219D77020B-11632-000009D899A71F81_zps84969508.jpg

[viinnh]

http://sphotos-e.ak.fbcdn.net/hphotos-ak-ash4/408855_4181740475366_1288367474_n.jpg

got it ready for all stars meet !

[Indie]

I died a little inside today when i walked to my car this morning to find a beautiful dent on the rear quarter panel and bumper. ****ing hit and runsSorry to hear that. Pathetic.

Celebrated 120,000kms today.

[eLtrix]

Sorry to hear that. Pathetic.

Celebrated 120,000kms today.

Be celebrating my 160,000kms soon...

Also thinking about selling my car after i fix it and get my a dc2r or dc5r, not sure which way i want to go. comfort or complete rawness of the dc2r

[Vvvtec]

dc2r isnt that raw :p

[89lude]

alexio i beg to differ :P

[Vvvtec]

alexio i beg to differ :P

Haha i know i know i just mean it as in its not like its unbearable to drive lol

[DTN]

Got my clutch cylinder fluid changed + quick wash :D

http://imageshack.us/a/img705/3185/itr02.jpg

[GSi_PSi]

Haha i know i know i just mean it as in its not like its unbearable to drive lol

For stock car it's pretty rickety lol. Not really a smooth drive.

[Super-DA9]

Got my clutch cylinder fluid changed + quick wash :D

http://imageshack.us/a/img705/3185/itr02.jpg

HNNNNGGGGG

naice!

lovin' the yellow DC2R's lately

[infurNOS]

http://i930.photobucket.com/albums/ad144/munro88/IMG_0771_zpsc466f345.jpg

Wasn't today though :P

Still tossing up whether i like black wheels better....

[dc2screama]

White rims!^

[DTN]

black ftw! :D

White jdm itr wheels is alrite if you lower it imo

http://i135.photobucket.com/albums/q153/dc2r888/31052009107edited.jpg

[rhys.l]

White looks rice with yellow. Definitely black mate.

[tripleuse]

white for sure.

[Frosty-Civic]

White looks rice with yellow. Definitely black mate.

nosureifsrs

[Dubstein]

Rice wut.

[rhys.l]

Riiiiiiiiiiiiiice. Haha I was serious, I think it's a terrible, way too bright combination, but that's what I think, not necessarily what you or others think. Whatever you do, much better than those hrv wheels :thumbsup:

[Vvvtec]

Looks alot nicer irl Rhys, imo alteast. Agreed with above comment though, also needs to be fairly slammed

[Cartoon]

I installed new door inner seals, hasport mounts, brake booster, peddles and rear wing today :)

[EKVTIR-T]

White looks rice with yellow.
agree




I vote gunmetal

[PHO]

White looks rice with yellow. Definitely black mate.

http://www.goldenrice.org/image/GoldenRice.jpg

[chubby steve]

after quite a long time finally got my motor together. is in the car now will update more pics later
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1780.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1777.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1778.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1775.jpg

[tripleuse]

steve youve been building this engine for 3 years atleast! hahah , how is the build going?

[chubby steve]

more like 5yrs just been very lazy. waiting on a knock sensor from the US and its all ready to go. worst part is running it in and not being able to put my foot down

[tripleuse]

more like 5yrs just been very lazy. waiting on a knock sensor from the US and its all ready to go. worst part is running it in and not being able to put my foot down

hahaha yeah true. what power are you expecting? and selling all your hondas? first the ep3 now the euro? :o

[Vvvtec]

after quite a long time finally got my motor together. is in the car now will update more pics later
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1780.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1777.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1778.jpg
http://i814.photobucket.com/albums/zz67/roach1187/IMG_1775.jpg

beautiful

[chubby steve]

hahaha yeah true. what power are you expecting? and selling all your hondas? first the ep3 now the euro? :o
hoping for around the 140kw mark. gonna keep the accord for a bit longer still miss the ep3 though might have to go kseries again in the future


beautiful

thanks alot. spent alot of time cleaning and painting

[dorikin]

What is that thing under your intake manifold? and what did you do with the breather chamber

[chubby steve]

What is that thing under your intake manifold? and what did you do with the breather chamber

black thing is like a little air box where all the vacuum hoses go to comes on the stock manifold so i just left it on. replaced chamber with sme hose fittings which will be going to a oil catch can and blocked the other hole with a welsh plug

[dorikin]

Ahhh it's a vti-r thing, thought that was a B18C7 lol nearly fooled me

[Super-DA9]

black thing is like a little air box where all the vacuum hoses go to comes on the stock manifold so i just left it on. replaced chamber with sme hose fittings which will be going to a oil catch can and blocked the other hole with a welsh plug

That black vacuum box is for IAB's only, you're supposed to remove it with the S2 manifold.

[harrytuckerr]

Hey Guys, bought my first Honda the other day, a white Integra VTI-R, so keen to get it! Completely stock from an old lady, 180*** on the clock, full service records, nothing wrong with it for a bargain price. Even still has the OEM tape player ;) shame I have to wait 2 weeks till I can get it though.

What sort of mods do you guys recommend for this model? I've already booked it in for a full exhaust system with an Xforce twin loop muffler and ordered a CAI. I was thinking of getting some king springs too, or should I just really blow the bank with some coilovers? Also, do you think this lip would look good on white? http://www.ebay.com.au/itm/Carbon-Fibre-Front-Lip-Spoiler-Integra-DC2-Type-R-/120743635766?pt=AU_Car_Parts_Accessories&hash=item1c1ce1ab36

[Super-DA9]

Hey Guys, bought my first Honda the other day, a white Integra VTI-R, so keen to get it! Completely stock from an old lady, 180*** on the clock, full service records, nothing wrong with it for a bargain price. Even still has the OEM tape player ;)

What sort of mods do you guys recommend for this model? I've already booked it in for a full exhaust system with an Xforce dual loop muffler and ordered a CAI. I was thinking of getting some king springs too, or should I just really blow the bank with some coilovers? Also, do you think this lip would look good on white? http://www.ebay.com.au/itm/Carbon-Fibre-Front-Lip-Spoiler-Integra-DC2-Type-R-/120743635766?pt=AU_Car_Parts_Accessories&hash=item1c1ce1ab36

Congrats on the great buy dude.

In terms of mods, it really depends if you're willing to open up the engine or not. if just bolt on's, then your CAI and full exhaust with headers should be quite nice. the Xforce twinloop (barrel type) cat back is actually pretty damn good for the price (I have one too), but the Xforce headers aren't really special at all..

Keep this in mind about king springs, if you put ANY significantly lowered springs on your stock shocks you will get terrible handling (worse than stock) and blow your stock shocks very quickly. for lowered springs you need to get lowered shocks to match. but then you're creeping into coilover territory ($ wise) anyway.

keep in mind even though coilovers provide superb handling some coilovers are quite stiff, even on the lowest shock setting. for daily driving (if stiff suspension bothers you) Buddyclub N+ are pretty good, they aren't too harsh at all on the lower settings.

That lip will fit fine provided your VTi-R is a 98-00 model.

[harrytuckerr]

Congrats on the great buy dude.

In terms of mods, it really depends if you're willing to open up the engine or not. if just bolt on's, then your CAI and full exhaust with headers should be quite nice. the Xforce twinloop (barrel type) cat back is actually pretty damn good for the price (I have one too), but the Xforce headers aren't really special at all..

Keep this in mind about king springs, if you put ANY significantly lowered springs on your stock shocks you will get terrible handling (worse than stock) and blow your stock shocks very quickly. for lowered springs you need to get lowered shocks to match. but then you're creeping into coilover territory ($ wise) anyway.

keep in mind even though coilovers provide superb handling some coilovers are quite stiff, even on the lowest shock setting. for daily driving (if stiff suspension bothers you) Buddyclub N+ are pretty good, they aren't too harsh at all on the lower settings.

That lip will fit fine provided your VTi-R is a 98-00 model.

Thanks man, beyond keen to get it! :D
I'm happy to open up the engine, are upgrading my cams worth the money?
Yeah, I've heard that about the Xforce headers, so I asked for hurricane to be put on.

I don't want it significantly lower, just at the moment it's height makes it look like a hairdressers car, I was thinking only around 1-1.5" drop. My last car, the previous owner dropped it heaps but didn't change the shocks so it was the most unpleasant ride driving over anything that wasn't brand new tarmac. I'll check those buddyclubs out too :)

Mine's 97 :( what about this one? http://www.ebay.com.au/itm/Carbon-Fibre-Front-Lip-Spoiler-JDM-Integra-DC2-Type-R-/120743639991?pt=AU_Car_Parts_Accessories&hash=item1c1ce1bbb7#ht_2712wt_906

[Super-DA9]

I'm happy to open up the engine, are upgrading my cams worth the money?

Best to go check out my post here: http://www.ozhonda.com/forum/showthread.php?168481-Cams-!&p=3556728#post3556728


Yeah, I've heard that about the Xforce headers, so I asked for hurricane to be put on.

Uhh, I haven't heard great things about hurricane either.. but see how it goes anyway :)


I don't want it significantly lower, just at the moment it's height makes it look like a hairdressers car, I was thinking only around 1-1.5" drop. My last car, the previous owner dropped it heaps but didn't change the shocks so it was the most unpleasant ride driving over anything that wasn't brand new tarmac. I'll check those buddyclubs out too :)

Even with 1.5" drop you will be out of the old stock shocks operating range. also when it comes to king springs they usually come in Superlow and Ultralow. I can tell you from experience that Superlow is easily enough to kill your stock shocks. just a warning! haha


Mine's 97 :( what about this one? http://www.ebay.com.au/itm/Carbon-Fibre-Front-Lip-Spoiler-JDM-Integra-DC2-Type-R-/120743639991?pt=AU_Car_Parts_Accessories&hash=item1c1ce1bbb7#ht_2712wt_906

Well first off, that is for a JDM front integra, and second if it's for a Type R (this does not include "Type R style") it wont fit.

What you need to be looking for is fitment for 93-97 (non-JDM) integra.

Go check out JDMYard in the trader section of this forum, they sell the same lip as the first one you posted to fit your vehicle.

[harrytuckerr]

Best to go check out my post here: http://www.ozhonda.com/forum/showthread.php?168481-Cams-!&p=3556728#post3556728



Uhh, I haven't heard great things about hurricane either.. but see how it goes anyway :)



Even with 1.5" drop you will be out of the old stock shocks operating range. also when it comes to king springs they usually come in Superlow and Ultralow. I can tell you from experience that Superlow is easily enough to kill your stock shocks. just a warning! haha



Well first off, that is for a JDM front integra, and second if it's for a Type R (this does not include "Type R style") it wont fit.

What you need to be looking for is fitment for 93-97 (non-JDM) integra.

Go check out JDMYard in the trader section of this forum, they sell the same lip as the first one you posted to fit your vehicle.

Thanks for all that! I feel like such a noob asking it all haha

[Super-DA9]

Thanks for all that! I feel like such a noob asking it all haha

It's alright man lol.

thats what forums are for, but it always helps to do some searching first. 9 times out of 10 the answers are already there :thumbsup:

[harrytuckerr]

It's alright man lol.

thats what forums are for, but it always helps to do some searching first. 9 times out of 10 the answers are already there :thumbsup:

If I had a black lip, matte black rims, would a black type r wing suit?

Wanting to look like this: http://image.hondatuningmagazine.com/f/features/htup_0601_1997_acura_integra_type_r/31250427+w620/htup_0601_01_o+1997_acura_integra_type_r+front_rig ht.jpg (but with AUDM headlights and maybe the black wing)

[Super-DA9]

If I had a black lip, matte black rims, would a black type r wing suit?

Wanting to look like this: http://image.hondatuningmagazine.com/f/features/htup_0601_1997_acura_integra_type_r/31250427+w620/htup_0601_01_o+1997_acura_integra_type_r+front_rig ht.jpg (but with AUDM headlights and maybe the black wing)


Up to you dude, it's your car.

My personal opinion though, type R wings on prefacelift (93-97) bodies look a bit lame unless you fit 98-00 facelift front and rear bumpers.

[tripleuse]

Hey Guys, bought my first Honda the other day, a white Integra VTI-R, so keen to get it! Completely stock from an old lady, 180*** on the clock, full service records, nothing wrong with it for a bargain price. Even still has the OEM tape player ;) shame I have to wait 2 weeks till I can get it though.

What sort of mods do you guys recommend for this model? I've already booked it in for a full exhaust system with an Xforce twin loop muffler and ordered a CAI. I was thinking of getting some king springs too, or should I just really blow the bank with some coilovers? Also, do you think this lip would look good on white? http://www.ebay.com.au/itm/Carbon-Fibre-Front-Lip-Spoiler-Integra-DC2-Type-R-/120743635766?pt=AU_Car_Parts_Accessories&hash=item1c1ce1ab36

dont ruin such a good example of a car, put some nice wheels on, good coils, but if you want to keep it clean id stop there. Then just engine mods dont put the wing on, IMO it will look shit/fanboy.

[Indie]

A black wing on a white car is a terrible idea.

[Dubstein]

cleaned good clean

[harrytuckerr]

A black wing on a white car is a terrible idea.

I went and built it in Forza and it looked crap haha

[Super-DA9]

I went and built it in Forza and it looked crap haha

Haha! Nice! Forza is mad for test fitting wheels and stuff XD

[harrytuckerr]

Haha! Nice! Forza is mad for test fitting wheels and stuff XD

it really is, I've pretty much used it to build a model of how I want it haha.

Also, will a JDM DC2R rear control arm fit a 97 AUDM VTI-R?

[tripleuse]

it really is, I've pretty much used it to build a model of how I want it haha.

Also, will a JDM DC2R rear control arm fit a 97 AUDM VTI-R?

yes it will, but your stock suspension wont fit into the control arm you will need to buy dc2r suspension or aftermarket.

[harrytuckerr]

yes it will, but your stock suspension wont fit into the control arm you will need to buy dc2r suspension or aftermarket.

Sweet! Yeah, I've bought type r coilovers which is why I want the LCA

[Setanta]

Got any pics champ?

I'll dig it out tomorrow and grab some pics

[Dubstein]

Someone buy my car

[viinnh]

http://sphotos-d.ak.fbcdn.net/hphotos-ak-ash3/75103_4223227272510_908488476_n.jpg
Spammed Aussie export paint on rear bar for fun. And taped up side moulds

[newpaddy3]

A black wing on a white car is a terrible idea.

http://25.media.tumblr.com/tumblr_lm7jzrrxem1qjv48ho1_500.jpg

[Indie]

http://25.media.tumblr.com/tumblr_lm7jzrrxem1qjv48ho1_500.jpgBecause that was funny the first time.

[harrytuckerr]

Ordered VTEC controller today. Can't wait to get my cams in and dyno tuned so I can use this bad boy to get me a sweet VTEC kick

[tripleuse]

Ordered VTEC controller today. Can't wait to get my cams in and dyno tuned so I can use this bad boy to get me a sweet VTEC kick

wouldnt use a vtec controller with bigger cams.Vtec controllers are terrible.

[harrytuckerr]

Why's that?

[tripleuse]

Why's that?

bigger cams= no torq, and then setting the vtec controller to a lower rpm, = no torq all noise no go.

[harrytuckerr]

bigger cams= no torq, and then setting the vtec controller to a lower rpm, = no torq all noise no go.

Oh okay. Well my intentions for the VTEC controller were to be able to change it to the optimum kick in after I get a dyno with my next exhaust, cams and intake so I can then change it to where the dyno tells me. Also to make it kick in higher when on freeways and stuff to save fuel.

[Super-DA9]

Oh okay. Well my intentions for the VTEC controller were to be able to change it to the optimum kick in after I get a dyno with my next exhaust, cams and intake so I can then change it to where the dyno tells me. Also to make it kick in higher when on freeways and stuff to save fuel.

what cams you got? when using bigger cams you would usually set the changeover to around 6000rpm.

but you cant just put in large cams + change vtec point = done. your engine will need to be tuned to get the performance othetwise itll probably be worse than stock.

[Super-DA9]

bigger cams= no torq.

not entirely true, pretty sure the torque just moves up the powerband.

[tripleuse]

not entirely true, pretty sure the torque just moves up the powerband.

this is true it does shift,but your shifting it to higher range, thus losing your low/mid range torque.

[Super-DA9]

this is true it does shift,but your shifting it to higher range, thus losing your low/mid range torque.

Yep thats better :)

it's the Low and Mid range torque you lose, depending on how much bigger the cams are. if it's only a mild increase in lift you will retain, and depending on the cam design, increase mid range but lose a little bit of low end torque.

however if you have big lift stage 3 cams you will lose a fair amount of low/mid in most cases as the power band is much higher up.

[93Integra]

Finally got my 2.25" cat-back made up by Carline Mufflers in Gawler (SA).

Used a Magnaflow muffler and resonator I bought from the forums, very happy :D

[Rayle]

Sick. How does it sound Jake? Post a clip!

Mandrel/press bent, stainless or mild steel?

[93Integra]

Surprisingly quiet in car, but a nice tone from outside.

Press bent mild steel with stainless from muffler to tip.

I recorded it with my phone but it sounded terrible, so I'll wait till I get a decent quality vid and chuck it on youtube :)

[harrytuckerr]

Definitely getting it tuned after my cams and before my controller. They're only stage one cams, just to add a little bit more of a punch up high.

[Dubstein]

Sneaky mods HAHAHHA

[Goku]

cant wait to get my car back!!!!! its been too long :(

[Tuan94]

Got my front bar resprayed along with the front lip, paint is correct colour, just newer than any of the other panels. Any way of blending it guys? :(
http://imageshack.us/a/img515/3826/photo13101251713pm.jpg

[bart2]

give the rest of the car a good wAsh / cut n ploish

[Arthsz]

well today i de badged the "type s" and "integra" off her rear, ran into a little bit of cactus though, the badge glue was the biggest c**t to get off
looks my-t-clean though :D

[Tuan94]

Nice, got any photos of it? :D

[khanguskhan]

Got my front bar resprayed along with the front lip, paint is correct colour, just newer than any of the other panels. Any way of blending it guys?

Your best chances with the paint blending would've been allowing them to paint with the car available as a whole, so they would lift the front part of your fender a few shades so that it matches up with your front bar.

[Tuan94]

Yeah, he told me to just bring the bar in (mates dad). As previously mentioned, would a cut and polish be able to match the paint? Or do I just have to live with it like that

[89lude]

Sold the daily

23167

[Goku]

Got my front bar resprayed along with the front lip, paint is correct colour, just newer than any of the other panels. Any way of blending it guys? :(
http://imageshack.us/a/img515/3826/photo13101251713pm.jpg

How much did the respray cost u bro?

[Tuan94]

Mates dad did it for $250

[SuperJDM.]

Mates dad did it for $250

for about $300-$350 you could had got it done with colour match lol. epic 50 shades of white.

getting the same colour code is easy but getting it colour matched is a different colour. Only way to make it blend is to get it sprayed again.

[EKVTIR-T]

At least they didnt spray the black centre vent white like other noob panelshops

[Tuan94]

I was getting quoted prices of ~450 for bar and lip to be painted :/ It's better than what it was before at least, and yeah, I asked him to spray the centre black :P

[dc2screama]

http://img.tapatalk.com/d/12/10/20/eby5usuj.jpg

Washed, Cut&polished the teggy!

[DC2-PWR]

http://img.tapatalk.com/d/12/10/20/eby5usuj.jpg

Washed, Cut&polished the teggy!

Good work thats looking great :)

[dc2screama]

Thanks mate, love your teg&colour!

[chubby steve]

http://i814.photobucket.com/albums/zz67/roach1187/IMG_1810.jpg
finally in after 5yrs runs well now for the long journey of running her in

[Dubstein]

Sexy :)

[Dubstein]

Thanks mate, love your teg&colour!

In need of a tin of b74p paint? ;) My teg was the same colour once haha

[dc2screama]

Haha nah all good man, thanks

[Killa From Manila]

installed oil press, oil temp, water temp gauges and a primary o2 sensor. fluids tomorrow then time for a tune soon

[tripleuse]

http://i814.photobucket.com/albums/zz67/roach1187/IMG_1810.jpg
finally in after 5yrs runs well now for the long journey of running her in

**** no way, hahahaha glad to see it all together now!

[Lukey]

http://sphotos-b.ak.fbcdn.net/hphotos-ak-prn1/525842_10152184977775696_954777590_n.jpg

[dc2r-0636]

Lolwut

[EKVTIR-T]

dat reflection

[Indie]

http://sphotos-b.ak.fbcdn.net/hphotos-ak-prn1/525842_10152184977775696_954777590_n.jpgBeen waiting to see this for a long time.

[Dubstein]

Finally!!

[mocchi]

lolwut

looks cool bra

[Lukey]

looks better in person than in the pics

[Dubstein]

New engine

[Goku]

new engine and clutch

[dc2screama]

http://img.tapatalk.com/d/12/10/27/y8y5yzav.jpg

Thoughts about the rims?
Dunno whether to keep them or not..

[eLtrix]

New engine

What did you put in?

new engine and clutch
What did you decide to do?


http://img.tapatalk.com/d/12/10/27/y8y5yzav.jpg

Thoughts about the rims?
Dunno whether to keep them or not..

Could be better bro. Looks okay, but i think something else could make it much more sexier

[Tai]

Theyre not even rims.

They're steelies.

[eLtrix]

Theyre not even rims.

They're steelies.

Was gonna say... didnt want to be mean... hah

[dc2screama]

Sticking to the blades then:p

[Indie]

Theyre not even rims.

They're steelies.'Rim' is just a misappropriated term, however. What makes an alloy wheel more of a 'rim' than a steelie?

[Xenox]

car wash...

[dc2r-0636]

dragged a ba fpv super pursuit ute, neck and neck till 160-170, if i had launched off the line i would of got him

*raced on private road*

[GSi_PSi]

dragged a ba fpv super pursuit ute, neck and neck till 160-170, if i had launched off the line i would of got him

*raced on private road*

thats pretty good man those taxi' utes are quite fast

[EKVTIR-T]

dragged a ba fpv super pursuit ute, neck and neck till 160-170, if i had launched off the line i would of got him

*raced on private road*
http://i41.tinypic.com/zsd8l.jpg

[infurNOS]

dragged a ba fpv super pursuit ute, neck and neck till 160-170, if i had launched off the line i would of got him

*raced on private road*

Which car?

[dc2r-0636]

In my stock dc2r lol just hav sri

[Tuan94]

DIY double din block off plate and sound deadening in the rear out, might spray over it.

http://imageshack.us/a/img820/3240/photo8111222504pm.jpg

http://imageshack.us/a/img339/3664/photo8111221928pm.jpg

[EKVTIR-T]

Imagine if it wasnt on private road and you got caught

probably end up on Today Tonight

[dc2r-0636]

Imagine if it wasnt on private road and you got caught

probably end up on Today Tonight

yeh i know right lol

[Dubstein]

Sold mine, wut do now? Might be moving over to the what did you do to your ed today thread ;)

[Dubstein]

Oh yeah were beating the eg thread and getting close to the ek thread too ;)

[dc2screama]

http://img.tapatalk.com/d/12/11/08/tejysyqa.jpg

Better then the steelies?from before^
Yeah l know, Needs moar low!

[typerdevil]

two new cosmetic things done: bolted a new cf bonnet and spoiler (OEM style ones) 3 weeks ago and never crunched a gear in the 4 years of driving my DC2R around Melbourne and Interstate SO NOW! i have booked my DC2R into Chasers, getting my hell noisy gearbox rebuilt, thankfully i can still shift into gears. :P cross my fingers it's not going to burn my wallet again.:confused:

[Goku]

got a set of new wheels and got rid off the gold blingy 18s that were on originally. looks so much better!

[eLtrix]

http://img.tapatalk.com/d/12/11/08/tejysyqa.jpg

Better then the steelies?from before^
Yeah l know, Needs moar low!

Yes it looks much better tbh. But at the end of the day buddy. It is your car, make sure YOU love it.

[DTN]

a mate gave me a set of blue rays nuts so decided to try them on (had black before) :)

http://imageshack.us/a/img822/5202/regasblue.jpg

[EKVTIR-T]

stick with the black imo

faded blue or red looks shit

[cbauto]

teg demoted to hardpark status

[Indie]

teg demoted to hardpark statusShould take it down to CB Auto and let him take a lo- oh, wait.

[infurNOS]

new rubber

[nate92]

installed my new headunit and fix my system. Cleaned the car inside out as i had nothing to do today!

http://i295.photobucket.com/albums/mm159/fineoner/IMG_0217.jpghttp://i295.photobucket.com/albums/mm159/fineoner/IMG_0212.jpghttp://i295.photobucket.com/albums/mm159/fineoner/IMG_0207.jpg